What did you do to your 2nd gen BRZ today?

[joemysterio]

Originally Posted by diga

Cusco pedal installed, I'm not finding any slop whatsoever. The Cusco pedal sits tightly on the factory pedal, no side-to-side slop, not sure what people are referencing in previous posts. It's much easier for me to heel-toe, I guess I have narrow/small feet, sometimes I'd roll my foot over to blip and I'd completely miss and my foot would be sort caught between the two pedals. This seems to have solved that issue, very easy/reliable to roll over to the accel pedal now.

Awesome!

I never learned to heel toe and when I tried for the first time the other day, I struggled mightily and also learned that I have small feet because I would miss most of the time LOL. Maybe my technique was off... but in any case, I'm going forward with getting this pedal. Thanks!

[soundman98]

Originally Posted by joemysterio

Awesome!

I never learned to heel toe and when I tried for the first time the other day, I struggled mightily and also learned that I have small feet because I would miss most of the time LOL. Maybe my technique was off... but in any case, I'm going forward with getting this pedal. Thanks!

do what works. i toe-toe and keep my heel planted. works just fine for rev-matching.

[diga]

Originally Posted by joemysterio

Awesome!

I never learned to heel toe and when I tried for the first time the other day, I struggled mightily and also learned that I have small feet because I would miss most of the time LOL. Maybe my technique was off... but in any case, I'm going forward with getting this pedal. Thanks!

I'm not new to stick shift cars but kind of new to heel/toe, the thing I didn't get until recently is you need to lift up your whole foot, use the ball of your foot on the brake then kind of angle out your heel and roll over onto the accel pedal. At least that's what's worked for me.

[Ohio Enthusiast]

In my experience there are two main ways to heel and toe:

1. Left edge of the shoe on the right side of the brake pedal. Roll the foot to the right to catch the gas pedal with the right edge of the shoe.
2. The ball of the foot on the brake pedal, shoe angled diagonally between the gas and brake pedal. Catch the gas pedal with the bottom right of the shoe.

I find that it greatly depends on the car, shoe size and shoe dimensions as well as personal preference and kinematics (position of the seat and steering wheel, proportions of the leg, etc.).
I used method 1 in my Focus ST, but switched to method 2 in my BRZ.

[OkieSnuffBox]

Originally Posted by Ohio Enthusiast

In my experience there are two main ways to heel and toe:

1. Left edge of the shoe on the right side of the brake pedal. Roll the foot to the right to catch the gas pedal with the right edge of the shoe.
2. The ball of the foot on the brake pedal, shoe angled diagonally between the gas and brake pedal. Catch the gas pedal with the bottom right of the shoe.

I find that it greatly depends on the car, shoe size and shoe dimensions as well as personal preference and kinematics (position of the seat and steering wheel, proportions of the leg, etc.).
I used method 1 in my Focus ST, but switched to method 2 in my BRZ.

That's how I do it. I was never able to keep consistent pressure on the brake pedal doing it the other way.

It was really difficult on a sportbike before they started using slipper clutches. My bike years ago did not have one. Don't get it right and you lock up the rear going into a corner.

[LancePower]

Method #1 for me also.

[rBobby]

I installed my SRP pedal cover. I have been using their wider gas pedals in most of my cars.

[Flarpswitch]

On my first cars, heel and toe was more double-clutch shifting. Some of my cars did not have a synchro first gear and the other gears had synchronizers that were total crap and would only work if you took your time between gears or were good at heel and toe. My later cars had full synchro gearboxes with floating synchro rings and not the press-on-the gear hub type. We affectionately call our transmissions "Crash Boxes". One time I missed a shift from second to third on my Triumph and knocked a tooth off the cluster gear. I still had a first gear if I needed it, but it went thunk, thunk, thunk. Those of you that were born after the first Moon Landing won't know of those joys.

[CZ6T]

Cleaned the ole beast. I've gotten most of the stuff done and settled, that I want to do right now, so I've been driving it around town mostly.

[OkieSnuffBox]

Originally Posted by CZ6T

Cleaned the ole beast. I've gotten most of the stuff done and settled, that I want to do right now, so I've been driving it around town mostly.

You're fitment and stance look great! Details?

[diga]

Originally Posted by Ohio Enthusiast

In my experience there are two main ways to heel and toe:

1. Left edge of the shoe on the right side of the brake pedal. Roll the foot to the right to catch the gas pedal with the right edge of the shoe.
2. The ball of the foot on the brake pedal, shoe angled diagonally between the gas and brake pedal. Catch the gas pedal with the bottom right of the shoe.

I find that it greatly depends on the car, shoe size and shoe dimensions as well as personal preference and kinematics (position of the seat and steering wheel, proportions of the leg, etc.).
I used method 1 in my Focus ST, but switched to method 2 in my BRZ.

my feet aren't big enough for #1, I'm stuck with #2 as my only option and even then I have to lift my foot up and angle it almost 45 degrees to reach the accel pedal...but I'm a women's size 8.5

[Yoshoobaroo]

Originally Posted by diga

my feet aren't big enough for #1, I'm stuck with #2 as my only option and even then I have to lift my foot up and angle it almost 45 degrees to reach the accel pedal...but I'm a women's size 8.5

The Cusco pedal cover may help you:

https://www.counterspacegarage.com/c...s-toyota-gr-86

[CZ6T]

Originally Posted by OkieSnuffBox

You're fitment and stance look great! Details?

I'm on superstreet-1 coilovers, lowered about 1.5" (last I checked, it may have settled a smidge more) and about -2.5⁰ camber all around. The wheels are 17x9" apex arc 8 with 245/40R/17 sumitomo HTR PS-03 tires.

[dragoontwo]

Originally Posted by CZ6T

I'm on superstreet-1 coilovers, lowered about 1.5" (last I checked, it may have settled a smidge more) and about -2.5⁰ camber all around. The wheels are 17x9" apex arc 8 with 245/40R/17 sumitomo HTR PS-03 tires.

Do you think the rears would clear with a bit less camber? -1.7 or so?