TRD Rear Bumper Cutout Template - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

electrongeek · 08-27-2016, 11:54 PM

I spent the last 30min searching, but have found nothing of use.

I recently purchased a used TRD rear bumper diffuser and would like to install it myself. I understand that cutting of my stock bumper is required to fit the TRD piece.

If anyone has a template or know of where I can get one then I'd appreciate the help.

turtlefeeder · 08-28-2016, 12:38 AM

It's easy where do you live might be able to help

Sent from my SM-P600 using Tapatalk

electrongeek · 08-28-2016, 02:02 AM

I live out in Chino Hills, but I do come down to OC often. If you can help then I'd really appreciate it.

turtlefeeder · 08-28-2016, 02:06 AM

yeah definitely bring a short saw or short mechanical saw if you have if not I guess I can borrow one well cut and slap it on.
here's mines

electrongeek · 08-28-2016, 02:20 AM

Nice!! Is that a Blitz quad tip exhaust?

Also would a dremel work? I don't have a mechanical saw.

electrongeek · 08-28-2016, 02:22 AM

Also I have the whole rear TRD bumper. Would that matter? I noticed you only have the exhaust garnish.

turtlefeeder · 08-28-2016, 02:22 AM

it's mxp sp quad burnt tip with TRD cutout

turtlefeeder · 08-28-2016, 02:23 AM

wait.. you got rid rear bumper with quad cutout?

electrongeek · 08-28-2016, 02:28 AM

No. What I meant was the TRD piece I have is the jdm lower half that goes onto the rear bumper.

Would the cuts be the the same as yours?

electrongeek · 08-28-2016, 02:30 AM

Like that one.

turtlefeeder · 08-28-2016, 02:45 AM

a bit different we need to measure the outline of the diffuser exit than mark than cut a bit wider to hide cut line. after we start installing

electrongeek · 08-28-2016, 02:48 AM

Ok. Cool. I gotta order some 3m tape and some weather stripping. I'll hit you up when I'm ready. Thanks for the help.

turtlefeeder · 08-28-2016, 02:49 AM

sure

olkpour · 09-11-2016, 10:02 PM

Quote:

Originally Posted by electrongeek

I spent the last 30min searching, but have found nothing of use.

I recently purchased a used TRD rear bumper diffuser and would like to install it myself. I understand that cutting of my stock bumper is required to fit the TRD piece.

If anyone has a template or know of where I can get one then I'd appreciate the help.

Where did you purchase this if you dont mind me asking? I have been trying to look into getting a trd rear bumper.

Sent from my SM-N920V using Tapatalk

08-27-2016, 11:54 PM	#1
electrongeek Member Join Date: Jul 2016 Drives: 2016 Scion FRS Location: So Cal Posts: 47 Thanks: 8 Thanked 6 Times in 5 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	TRD Rear Bumper Cutout Template I spent the last 30min searching, but have found nothing of use. I recently purchased a used TRD rear bumper diffuser and would like to install it myself. I understand that cutting of my stock bumper is required to fit the TRD piece. If anyone has a template or know of where I can get one then I'd appreciate the help.

08-28-2016, 02:06 AM	#4
turtlefeeder Senior Member Join Date: Apr 2016 Drives: UltraMFrS Location: OC Posts: 701 Thanks: 204 Thanked 135 Times in 100 Posts Mentioned: 3 Post(s) Tagged: 0 Thread(s)	yeah definitely bring a short saw or short mechanical saw if you have if not I guess I can borrow one well cut and slap it on. here's mines Last edited by turtlefeeder; 08-28-2016 at 04:56 AM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
TRD Rear Bumper "Cutout Template"?	Dboe	Northern California	12	02-19-2016 01:24 AM
Stock bumper with vent cutout for sale!	genometuning	Exterior Parts (Aero, Lighting, Etc.)	7	12-03-2014 02:15 PM
WTB: South East PA BRZ front bumper, rear bumper.	SterlingBrz	Want-To-Buy Requests	1	06-10-2014 10:37 AM
Rear Bumper removal / bumper latch	SmartedPanda	Cosmetic Modification (Interior/Exterior/Lighting)	3	05-01-2014 01:27 PM
Free-Rear bumper cover (entire rear facia) replaced after slight rear-end collision	n7011n	Exterior Parts (Aero, Lighting, Etc.)	7	03-26-2014 04:46 AM

08-28-2016, 12:38 AM	#2
turtlefeeder Senior Member Join Date: Apr 2016 Drives: UltraMFrS Location: OC Posts: 701 Thanks: 204 Thanked 135 Times in 100 Posts Mentioned: 3 Post(s) Tagged: 0 Thread(s)	It's easy where do you live might be able to help Sent from my SM-P600 using Tapatalk

08-28-2016, 02:02 AM	#3
electrongeek Member Join Date: Jul 2016 Drives: 2016 Scion FRS Location: So Cal Posts: 47 Thanks: 8 Thanked 6 Times in 5 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	I live out in Chino Hills, but I do come down to OC often. If you can help then I'd really appreciate it.

08-28-2016, 02:20 AM	#5
electrongeek Member Join Date: Jul 2016 Drives: 2016 Scion FRS Location: So Cal Posts: 47 Thanks: 8 Thanked 6 Times in 5 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Nice!! Is that a Blitz quad tip exhaust? Also would a dremel work? I don't have a mechanical saw.

08-28-2016, 02:22 AM	#6
electrongeek Member Join Date: Jul 2016 Drives: 2016 Scion FRS Location: So Cal Posts: 47 Thanks: 8 Thanked 6 Times in 5 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Also I have the whole rear TRD bumper. Would that matter? I noticed you only have the exhaust garnish.

08-28-2016, 02:23 AM	#8
turtlefeeder Senior Member Join Date: Apr 2016 Drives: UltraMFrS Location: OC Posts: 701 Thanks: 204 Thanked 135 Times in 100 Posts Mentioned: 3 Post(s) Tagged: 0 Thread(s)	wait.. you got rid rear bumper with quad cutout?

08-28-2016, 02:28 AM	#9
electrongeek Member Join Date: Jul 2016 Drives: 2016 Scion FRS Location: So Cal Posts: 47 Thanks: 8 Thanked 6 Times in 5 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	No. What I meant was the TRD piece I have is the jdm lower half that goes onto the rear bumper. Would the cuts be the the same as yours?

08-28-2016, 02:30 AM	#10
electrongeek Member Join Date: Jul 2016 Drives: 2016 Scion FRS Location: So Cal Posts: 47 Thanks: 8 Thanked 6 Times in 5 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Like that one.

08-28-2016, 02:45 AM	#11
turtlefeeder Senior Member Join Date: Apr 2016 Drives: UltraMFrS Location: OC Posts: 701 Thanks: 204 Thanked 135 Times in 100 Posts Mentioned: 3 Post(s) Tagged: 0 Thread(s)	a bit different we need to measure the outline of the diffuser exit than mark than cut a bit wider to hide cut line. after we start installing

08-28-2016, 02:48 AM	#12
electrongeek Member Join Date: Jul 2016 Drives: 2016 Scion FRS Location: So Cal Posts: 47 Thanks: 8 Thanked 6 Times in 5 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Ok. Cool. I gotta order some 3m tape and some weather stripping. I'll hit you up when I'm ready. Thanks for the help.

08-28-2016, 02:49 AM	#13
turtlefeeder Senior Member Join Date: Apr 2016 Drives: UltraMFrS Location: OC Posts: 701 Thanks: 204 Thanked 135 Times in 100 Posts Mentioned: 3 Post(s) Tagged: 0 Thread(s)	sure

User Name		Remember Me?
Password