my interior re-design - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

Jive Turkey · 07-17-2013, 11:37 AM

i changed it up a bit.

all wrapping and stitching was done by Overland Designs (www.overland-designs.com). fabrication and etc done by me.

first of all, i hated not having an armrest so the OEM armrest was a must. then i was really not happy with the fact that there isn't enough cubby room/holes in the car, nowhere to put my phone, etc etc. so i decided to change it up and make this interior more to what I like and would want.

i unded up relocating a few things. here is so far what is done:

1) push start went where heated seats were. (Sti pushbutton/AUS black buttons)
2) Heated seat went infront of shifter by each seat
3) cut out the limited din thats next to push start button, cut and molded it to fit center console.
4) Add genuine leather kneed pads and speaker pads.
5) since push start was moved, the bigger Premium brz din was added for more room.
6) Mold center trim into one piece, genuine Alcantara wrapped by Overland Designs (www.overland-designs.com)
7) Alcantara hvac surrouns
8) Alcantara vent rings
9) Alcantara and Red stitched Center Vent trim
10) Alcantara and Red stitched e brake boot
11) Red Alcantara with black stitching Shift boot
12) "Black Jack" powder coated @Anarchy Motive knob with aluminum reverse lockout.
13) Perforated Alcantara door cards where em plastic perforated is
14) red GT3 pullstraps (door lever delete) with perforated alcantara block off plates
15) Alcantara and Red stitched cluster hood
16) dual clsuter 52mm gauge pod made by me.
17) Alcantara re-wrapped OEM wheel (pending)
18) E90 cupholders molded into passenger dash (pending)

here is where it started, and what it turned out like. i molder glued and did the relocating. Its wrapped by Overland04 (nasioc name) and the fabric is genuine blakc alcantara from JPM.

i will update once everything is in the car, let me know what you think.

https://www.facebook.com/OverlandDesigns

and here are the photos:

final results:

PART 2 of my over haul

replacing door handles with GT2 RS style pull straps, added perforated alcantara to door cards, wrapped/stirched hood/ebrake/center vent

[ame]http://youtu.be/9RrUtvuFIGs[/ame]

part 3:

starting to clean it up. went with the STi blue edition button, picked it up at the local dealership and then painted the ring gloss black. now i need to figure out what to do with the shift knob, copper is no longer appealing to me.

interior before:

Button:

Before/After

i'm leaning towards some sort of shade of black, but honestly i don't know for sure, but the copper has to go.

Decided to go with a red boot.

-ivan

TheBatman · 07-17-2013, 11:45 AM

Looks sweet!

DIM · 07-17-2013, 11:52 AM

This looks awesome, can't wait to see everything done.

SkAsphalt · 07-17-2013, 12:36 PM

Um...wow.

Baldoak · 07-17-2013, 12:46 PM

I've been considering doing Alcantara wraps myself as well. Can you comment on the process or difficulty of doing so?

Norkoastal · 07-17-2013, 12:50 PM

Looking Mighty Schwing!

Diode Dynamics · 07-17-2013, 12:52 PM

Very impressive, can't wait to see the final installed pics and everything

-Nick C.

jadewbj · 07-17-2013, 12:54 PM

This makes me for sure that I will be wrapping my speaker pads, knee pads, center console and gauge hood. It should do well with the new Carbon stuff going in soon.

qoncept · 07-17-2013, 12:58 PM

Whoa whoa whoa.. your VSC/TC buttons.. Did you paint them?

Chase86 · 07-17-2013, 01:18 PM

Wow!! Impressed

RallySport Direct · 07-17-2013, 01:18 PM

Quote:

Originally Posted by qoncept

Whoa whoa whoa.. your VSC/TC buttons.. Did you paint them?

Those should be the OEM Australian Black buttons. I want some quite badly

Ivan, that looks amazing, great work!

Thanks,
Rick

Jive Turkey · 07-17-2013, 02:51 PM

Quote:

Originally Posted by RallySport Direct

Those should be the OEM Australian Black buttons. I want some quite badly

Ivan, that looks amazing, great work!

Thanks,
Rick

i told you to stock up on them...i think that should be the next item you unvail, because sourcing them and waiting months is not fun.

btw rick, how hard was it to rewire the toms tails...DO WANT.

RallySport Direct · 07-17-2013, 03:16 PM

Quote:

Originally Posted by Jive Turkey

i told you to stock up on them...i think that should be the next item you unvail, because sourcing them and waiting months is not fun.

btw rick, how hard was it to rewire the toms tails...DO WANT.

Yeah I know we are looking into it, not too sure how far we have got with them yet.

And the Tails were super easy to re-pin, I think it took me about 15 minutes total and that included the testing to make sure I had the pins correct lol. Let me know if you have any questions on them

Thanks,
Rick

suaveflooder · 07-17-2013, 03:36 PM

Interesting....interested to see how it all turns out installed.

07-17-2013, 11:37 AM	#1
Jive Turkey the tuna, no crust. Join Date: Oct 2012 Drives: 2014 Hachiroku of the year Location: jersey Posts: 2,298 Thanks: 874 Thanked 1,770 Times in 761 Posts Mentioned: 78 Post(s) Tagged: 0 Thread(s)	my interior re-design i changed it up a bit. all wrapping and stitching was done by Overland Designs (www.overland-designs.com). fabrication and etc done by me. first of all, i hated not having an armrest so the OEM armrest was a must. then i was really not happy with the fact that there isn't enough cubby room/holes in the car, nowhere to put my phone, etc etc. so i decided to change it up and make this interior more to what I like and would want. i unded up relocating a few things. here is so far what is done: 1) push start went where heated seats were. (Sti pushbutton/AUS black buttons) 2) Heated seat went infront of shifter by each seat 3) cut out the limited din thats next to push start button, cut and molded it to fit center console. 4) Add genuine leather kneed pads and speaker pads. 5) since push start was moved, the bigger Premium brz din was added for more room. 6) Mold center trim into one piece, genuine Alcantara wrapped by Overland Designs (www.overland-designs.com) 7) Alcantara hvac surrouns 8) Alcantara vent rings 9) Alcantara and Red stitched Center Vent trim 10) Alcantara and Red stitched e brake boot 11) Red Alcantara with black stitching Shift boot 12) "Black Jack" powder coated @Anarchy Motive knob with aluminum reverse lockout. 13) Perforated Alcantara door cards where em plastic perforated is 14) red GT3 pullstraps (door lever delete) with perforated alcantara block off plates 15) Alcantara and Red stitched cluster hood 16) dual clsuter 52mm gauge pod made by me. 17) Alcantara re-wrapped OEM wheel (pending) 18) E90 cupholders molded into passenger dash (pending) here is where it started, and what it turned out like. i molder glued and did the relocating. Its wrapped by Overland04 (nasioc name) and the fabric is genuine blakc alcantara from JPM. i will update once everything is in the car, let me know what you think. https://www.facebook.com/OverlandDesigns and here are the photos: final results: PART 2 of my over haul replacing door handles with GT2 RS style pull straps, added perforated alcantara to door cards, wrapped/stirched hood/ebrake/center vent [ame]http://youtu.be/9RrUtvuFIGs[/ame] part 3: starting to clean it up. went with the STi blue edition button, picked it up at the local dealership and then painted the ring gloss black. now i need to figure out what to do with the shift knob, copper is no longer appealing to me. interior before: Button: Before/After i'm leaning towards some sort of shade of black, but honestly i don't know for sure, but the copper has to go. Decided to go with a red boot. -ivan Last edited by Jive Turkey; 01-31-2015 at 12:17 AM.

07-17-2013, 11:52 AM	#3
DIM Senior Member Join Date: Sep 2012 Drives: 2013 Scion FR-S Location: San Antonio TX / Dyess AFB Posts: 948 Thanks: 26 Thanked 451 Times in 242 Posts Mentioned: 11 Post(s) Tagged: 1 Thread(s)	This looks awesome, can't wait to see everything done. __________________

07-17-2013, 12:52 PM	#7
Diode Dynamics Join Date: Aug 2012 Drives: 2013 Scion FR-S Location: St. Louis, Missouri Posts: 2,770 Thanks: 1,503 Thanked 1,761 Times in 877 Posts Mentioned: 197 Post(s) Tagged: 5 Thread(s)	Very impressive, can't wait to see the final installed pics and everything -Nick C. __________________ John C. Diode Dynamics Follow Us: FB // IG // YT // TikTok

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DCW Carbon Fiber interior items! Center console Plaques / Interior panels	doggy	Interior Parts (Incl. Lighting)	143	10-11-2013 11:17 AM
LED interior conversion kits (interior), USA stock & warranty	WTF	Interior Parts (Incl. Lighting)	0	05-22-2013 10:17 PM
Video: Toyota FT-86 II Concept Design Explained by "Dezi" Nagaya (Design Manager)	Hachiroku	Scion FR-S / Toyota 86 GT86 General Forum	58	04-11-2011 09:03 PM

07-17-2013, 12:46 PM	#5
Baldoak BRZ N02 Join Date: Mar 2013 Drives: 2013 A/T Subaru BRZ Limited, SWP Location: Oregon Posts: 82 Thanks: 87 Thanked 45 Times in 30 Posts Mentioned: 8 Post(s) Tagged: 2 Thread(s)	I've been considering doing Alcantara wraps myself as well. Can you comment on the process or difficulty of doing so?

07-17-2013, 01:18 PM	#10
Chase86 Member Join Date: May 2013 Drives: Ultramarine FRS Location: Phoenix, AZ Posts: 60 Thanks: 14 Thanked 7 Times in 7 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Wow!! Impressed

07-17-2013, 03:36 PM	#14
suaveflooder Senior Member Join Date: Feb 2013 Drives: 2013 FR-S Location: San Diego Posts: 2,295 Thanks: 2,708 Thanked 1,052 Times in 664 Posts Mentioned: 29 Post(s) Tagged: 0 Thread(s)	Interesting....interested to see how it all turns out installed.

User Name		Remember Me?
Password