|
Cosmetic Modification (Interior/Exterior/Lighting) Discussions about cosmetic mods. |
|
Thread Tools | Search this Thread |
05-10-2022, 06:55 PM | #1 |
Senior Member
Join Date: Jun 2013
Drives: '13 BRZ
Location: CT
Posts: 485
Thanks: 314
Thanked 330 Times in 155 Posts
Mentioned: 6 Post(s)
Tagged: 1 Thread(s)
|
JDM armrest hinge keeps popping out?
Hello - I just bought a brand new Toyota armrest to replace my 8 year old broken one. Installation was a breeze since the holes were already drilled for the old armrest. I have noticed over the past few weeks that every time I open the arm rest, the rear "hinge" pops out of its guide slot. Am I missing a part? Is there something that is supposed to keep the rear hinge captive like the front hinge? I can push it back in place while I close it, but it pops out every single time I open it. The mounting hardware is barely snug, so I don't believe it's warped or anything.
|
05-10-2022, 09:35 PM | #2 |
ProCrastinationConsultant
Join Date: Sep 2013
Drives: '14 Ranger, '18 Tacoma 4Dr LB
Location: chicago-ish
Posts: 11,330
Thanks: 35,240
Thanked 13,673 Times in 6,781 Posts
Mentioned: 98 Post(s)
Tagged: 0 Thread(s)
|
i thought there were some screws that went through that? could be wrong though
__________________
"The time you enjoy wasting is not wasted time"
|
The Following User Says Thank You to soundman98 For This Useful Post: | tobin (05-11-2022) |
05-11-2022, 02:59 AM | #3 |
Junior Member
Join Date: Jul 2020
Drives: 2013 GT86 Limited
Location: The Netherlands
Posts: 6
Thanks: 0
Thanked 1 Time in 1 Post
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Mine did the same thing twice. Had to disassemble it the first time because the pin in the hinge got loose. The second time the hinge itself broke.
Love the armrest but the hinge seems pretty shitty. I don't have any pressure on the structure of the armrest either. |
The Following User Says Thank You to RapidEntropy For This Useful Post: | tobin (05-11-2022) |
05-11-2022, 04:29 AM | #4 |
FT86Club Vancouver
Join Date: Jun 2012
Drives: BRZ Sport-Tech; Drove: MR-S, AE86
Location: Vancouver, BC
Posts: 2,532
Thanks: 391
Thanked 1,178 Times in 633 Posts
Mentioned: 16 Post(s)
Tagged: 2 Thread(s)
|
There's supposed to be some metal studs that poke out from the plastic part that hinges the two pieces together on both ends, they may have been retracted into the plastic itself.
I had this happened to me before... The solution is to take those circular covers off and undo the torq screws and push the studs back out. I then used CRAZY Glue to glue them back in place so they will NEVER retract again.
__________________
1984 AE86 BT 20V 5MT 2007-2012
2000 MR-S 5MT 2010-2012 2013 BRZ Sport-Tech 6AT Since '12 (OEM+ STI tS Build) 2015 Lexus IS250 AWD F-Sport 2 2015-2018 2018 Lexus NX300 F-Sport 3 Since '18 |
The Following 5 Users Say Thank You to DaJo For This Useful Post: | Nails (05-11-2022), soundman98 (05-11-2022), Tcoat (05-11-2022), tobin (05-11-2022), wolffbite (05-11-2022) |
05-11-2022, 06:21 AM | #5 |
Senior Member
Join Date: Jun 2013
Drives: '13 BRZ
Location: CT
Posts: 485
Thanks: 314
Thanked 330 Times in 155 Posts
Mentioned: 6 Post(s)
Tagged: 1 Thread(s)
|
Thank you so much! I opened the top and found the loose stud unattached to anything. I put it back in place and added a few drops of super glue to keep it in place (added a few drops to the front stud too). Great solution. Thank you for your reply!
|
The Following 5 Users Say Thank You to tobin For This Useful Post: | AJ32162 (05-11-2022), soundman98 (05-11-2022), Tcoat (05-11-2022), wolffbite (05-11-2022), x808drifter (05-11-2022) |
05-11-2022, 06:13 PM | #6 |
FT86Club Vancouver
Join Date: Jun 2012
Drives: BRZ Sport-Tech; Drove: MR-S, AE86
Location: Vancouver, BC
Posts: 2,532
Thanks: 391
Thanked 1,178 Times in 633 Posts
Mentioned: 16 Post(s)
Tagged: 2 Thread(s)
|
Glad it worked out! Mine is still going strong too.
__________________
1984 AE86 BT 20V 5MT 2007-2012
2000 MR-S 5MT 2010-2012 2013 BRZ Sport-Tech 6AT Since '12 (OEM+ STI tS Build) 2015 Lexus IS250 AWD F-Sport 2 2015-2018 2018 Lexus NX300 F-Sport 3 Since '18 |
The Following 2 Users Say Thank You to DaJo For This Useful Post: | soundman98 (05-11-2022), tobin (05-11-2022) |
05-11-2022, 07:26 PM | #7 |
Just the tip
Join Date: Mar 2017
Drives: 2017 DGM BRZ
Location: BC, CANADA
Posts: 630
Thanks: 912
Thanked 875 Times in 376 Posts
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
|
Ha! I had the exact same issues when I first installed mine.
Pin was loose, but mine was actually caused by the plastic sleeve around it cracking. I ended up using a liberal amount of JB Weld plastic bonder from the inside to repair it. The other side was fine, but I added the plastic bonder there to beef it up just in case. Been solid ever since. |
The Following 2 Users Say Thank You to wolffbite For This Useful Post: | soundman98 (05-11-2022), tobin (05-11-2022) |
05-11-2022, 07:33 PM | #8 | |
FT86Club Vancouver
Join Date: Jun 2012
Drives: BRZ Sport-Tech; Drove: MR-S, AE86
Location: Vancouver, BC
Posts: 2,532
Thanks: 391
Thanked 1,178 Times in 633 Posts
Mentioned: 16 Post(s)
Tagged: 2 Thread(s)
|
Quote:
__________________
1984 AE86 BT 20V 5MT 2007-2012
2000 MR-S 5MT 2010-2012 2013 BRZ Sport-Tech 6AT Since '12 (OEM+ STI tS Build) 2015 Lexus IS250 AWD F-Sport 2 2015-2018 2018 Lexus NX300 F-Sport 3 Since '18 |
|
The Following User Says Thank You to DaJo For This Useful Post: | tobin (05-13-2022) |
05-13-2022, 03:32 PM | #9 |
Senior Member
Join Date: Feb 2014
Drives: Corolla GT
Location: Sunny place.
Posts: 208
Thanks: 371
Thanked 118 Times in 90 Posts
Mentioned: 6 Post(s)
Tagged: 2 Thread(s)
|
Looks like its a common issue with this armrest.
A bit of glue helps secure things. Had same problem and sorted out like everyone mentioned above. |
The Following 2 Users Say Thank You to Thefalls For This Useful Post: | soundman98 (05-13-2022), tobin (05-13-2022) |
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Door Hinge and Bolt Covers | jelder9 | Interior Parts (Incl. Lighting) | 2 | 01-08-2022 03:36 PM |
GCS Black Door Hinge Covers - NEW - 2013+ FR-S / BRZ / 86 | burgeralert | Exterior Parts (Aero, Lighting, Etc.) | 9 | 01-05-2021 11:13 PM |
DWL Front splitter fastener / hinge - replacement part? | 1Cor10:23 | Tracking / Autocross / HPDE / Drifting | 0 | 07-04-2016 12:28 PM |
WTB: OEM armrest or Sutty's custom armrest | J.C. | Want-To-Buy Requests | 0 | 10-20-2014 06:07 PM |
Ideal armrest hinge | TIE Pilot | Cosmetic Modification (Interior/Exterior/Lighting) | 4 | 02-24-2013 12:44 PM |