Bell housing dowel pins in transmission - Page 2 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

Grady · 11-06-2022, 09:50 AM

Take it back apart and inspect the pilot bearing. Never put a bolt in it to help line it up or pull it together. I would reset the clutch with your alignment tool. If you are using the plastic one it will flex down with the weight of the clutch. Support it and then eyeball it to make sure it looks straight. Once everything is lined up right it will push together all the way. As stated above if you do not support the front of the engine it will rock down and make it more difficult to install.

blsfrs · 11-07-2022, 08:55 AM

Quote:

Originally Posted by Grady

Take it back apart and inspect the pilot bearing. Never put a bolt in it to help line it up or pull it together. I would reset the clutch with your alignment tool. If you are using the plastic one it will flex down with the weight of the clutch. Support it and then eyeball it to make sure it looks straight. Once everything is lined up right it will push together all the way. As stated above if you do not support the front of the engine it will rock down and make it more difficult to install.

Completely agree with @Grady. I've always used the cheap plastic alignment tools and never have had a problem. They will droop, so hold a little upward pressure until 2-3 of the pressure plate bolts are snug. Once torqued, make sure the tool will easy slide in and out a couple of times. Then cuddle.

carson.frs · 11-08-2022, 06:55 PM

Alright everyone. Here's a little update on everything. I had the car towed to a friends shop so I could use a lift and that definitely helps. What I ended up doing was removing the two bottom bolts that the trans sits on and instead aligned the dowels straight in and then I just screwed those 2 bolts back in. I think those bolts might have been a little bent but either way, that made the trans going on MUCH easier. One of those bottom bolts was already loose anyways so I decided to try it out and everything seems to have lined up just fine. I'll be testing it all tomorrow after I get everything back together so hopefully everything works but the engine and trans are flush and the transmission is engaged.

And by the way we used bolts for the last maybe 1/5 of an inch to just pull them together which helped a lot.

carson.frs · 11-30-2022, 11:59 AM

Ok sorry for no update. Took it to a friends shop and got it on a lift and I ended up taking off the bolts that the transmission actually slides onto because one was already loose and seemed to be bent. I then got it to the dowels and after some pushing, then pulled it in with the rest of the bell housing bolts very carefully. I screwed those bolts back in using the 2 nuts stacked method and it drives great. Also I’m not sure how much it helped but we did spin the crankshaft while pushing it in to make things easier.

Thanks everyone for the help!

Ultramaroon · 11-30-2022, 01:27 PM

Great to hear! Thanks for the closure.

villainous_frx · 11-30-2022, 10:49 PM

Quote:

Originally Posted by Ultramaroon

Great to hear! Thanks for the closure.

Super satisfying when people actually post that they resolved an issue, especially on an open forum.

NoHaveMSG · 11-30-2022, 11:02 PM

Quote:

Originally Posted by villainous_frx

Super satisfying when people actually post that they resolved an issue, especially on an open forum.

Reminds me of this meme.

11-30-2022, 01:27 PM	#19
Ultramaroon 義理チョコ Join Date: Sep 2014 Drives: a 13 e8h frs Location: vantucky, wa Posts: 31,865 Thanks: 52,120 Thanked 36,513 Times in 18,917 Posts Mentioned: 1106 Post(s) Tagged: 9 Thread(s)	Great to hear! Thanks for the closure. __________________ service manuals

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Messed Up Bell Housing Bolts	tobsadness	Engine, Exhaust, Transmission	4	09-25-2022 01:07 AM
How bad did I screw up my bell housing?	DigitalVeil92	Engine, Exhaust, Transmission	33	08-12-2022 12:06 AM
Rubber Cover Fell Into Transmission Bell Housing	trinidadj	Engine, Exhaust, Transmission	15	06-30-2021 11:58 AM
FS: Verus Bell Housing Cover	skylinekin	Engine, Exhaust, Bolt-Ons	2	09-07-2018 10:21 PM
Clutch squeak inside bell housing?	hukdizzle	Issues \| Warranty \| Recalls / TSB	18	07-18-2015 11:54 AM

11-08-2022, 06:55 PM	#17
carson.frs Member Join Date: Nov 2022 Drives: 2014 FRS Location: Utah Posts: 11 Thanks: 0 Thanked 12 Times in 3 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Alright everyone. Here's a little update on everything. I had the car towed to a friends shop so I could use a lift and that definitely helps. What I ended up doing was removing the two bottom bolts that the trans sits on and instead aligned the dowels straight in and then I just screwed those 2 bolts back in. I think those bolts might have been a little bent but either way, that made the trans going on MUCH easier. One of those bottom bolts was already loose anyways so I decided to try it out and everything seems to have lined up just fine. I'll be testing it all tomorrow after I get everything back together so hopefully everything works but the engine and trans are flush and the transmission is engaged. And by the way we used bolts for the last maybe 1/5 of an inch to just pull them together which helped a lot.

11-30-2022, 11:59 AM	#18
carson.frs Member Join Date: Nov 2022 Drives: 2014 FRS Location: Utah Posts: 11 Thanks: 0 Thanked 12 Times in 3 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Ok sorry for no update. Took it to a friends shop and got it on a lift and I ended up taking off the bolts that the transmission actually slides onto because one was already loose and seemed to be bent. I then got it to the dowels and after some pushing, then pulled it in with the rest of the bell housing bolts very carefully. I screwed those bolts back in using the 2 nuts stacked method and it drives great. Also I’m not sure how much it helped but we did spin the crankshaft while pushing it in to make things easier. Thanks everyone for the help!

User Name		Remember Me?
Password