follow ft86club on our blog, twitter or facebook.
FT86CLUB
Ft86Club
Delicious Tuning
Register Garage Members List Calendar Search Today's Posts Mark Forums Read

Go Back   Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB > Technical Topics > Tracking / Autocross / HPDE / Drifting

Tracking / Autocross / HPDE / Drifting What these cars were built for!


User Tag List

Reply
 
Thread Tools Search this Thread
Old 09-05-2024, 10:47 AM   #57
ZDan
Senior Member
 
ZDan's Avatar
 
Join Date: May 2011
Drives: '23 BRZ
Location: Providence, RI
Posts: 4,634
Thanks: 1,417
Thanked 3,963 Times in 2,071 Posts
Mentioned: 85 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by Tomyyyu View Post
I would avoid the rear bar. 949 is pretty adamant on that and he’s a knowledgeable poster.
Going from 15mm to 16mm rear bar (29% stiffer) isn't going to hurt anything and is just about the easiest/cheapest thing to do. Also not likely to help if the issue is really front bump travel and being on the outside bumpstop midcorner...
ZDan is offline   Reply With Quote
The Following User Says Thank You to ZDan For This Useful Post:
Spuds (09-05-2024)
Old 09-05-2024, 03:06 PM   #58
Tomyyyu
Member
 
Join Date: May 2023
Drives:
Posts: 79
Thanks: 19
Thanked 21 Times in 17 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)

Got it aligned and corner balanced.

7 out of 12 gallons. On RPF1 17x9 A052 245/40/17.


Sent from my iPhone using Tapatalk
Tomyyyu is offline   Reply With Quote
The Following User Says Thank You to Tomyyyu For This Useful Post:
ZDan (09-05-2024)
Old 09-05-2024, 04:41 PM   #59
ZDan
Senior Member
 
ZDan's Avatar
 
Join Date: May 2011
Drives: '23 BRZ
Location: Providence, RI
Posts: 4,634
Thanks: 1,417
Thanked 3,963 Times in 2,071 Posts
Mentioned: 85 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by Tomyyyu View Post
Got it aligned and corner balanced.
You went to the right place! Those guys are da best...

Are you in COMSCC? Come to NHMS next month!
ZDan is offline   Reply With Quote
Old 09-05-2024, 04:53 PM   #60
Tomyyyu
Member
 
Join Date: May 2023
Drives:
Posts: 79
Thanks: 19
Thanked 21 Times in 17 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by ZDan View Post
You went to the right place! Those guys are da best...

Are you in COMSCC? Come to NHMS next month!

I’m a CT person who drives two hours to and from Devens MA. Love that site too much.

Tried others, but Devens had the most competitive talent and lovely site.


Sent from my iPhone using Tapatalk
Tomyyyu is offline   Reply With Quote
The Following User Says Thank You to Tomyyyu For This Useful Post:
ZDan (09-06-2024)
Old 09-06-2024, 02:07 PM   #61
Tomyyyu
Member
 
Join Date: May 2023
Drives:
Posts: 79
Thanks: 19
Thanked 21 Times in 17 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
@ Went ahead and measured my center of wheel to fender and ended up with these heights. Are these too tall? Leading to too little droop travel?

RF - 14 2/16”
RR - 14 6/16”
LF - 14”
LR - 14 8/16”


Sent from my iPhone using Tapatalk
Tomyyyu is offline   Reply With Quote
Old 09-06-2024, 03:37 PM   #62
Racecomp Engineering
 
Join Date: Nov 2011
Drives: 2016 BRZ, 2012 Paris Di2 & 2018 STI
Location: Severn, MD
Posts: 5,461
Thanks: 3,497
Thanked 7,348 Times in 3,002 Posts
Mentioned: 305 Post(s)
Tagged: 9 Thread(s)
Send a message via AIM to Racecomp Engineering
Quote:
Originally Posted by Tomyyyu View Post
@ Went ahead and measured my center of wheel to fender and ended up with these heights. Are these too tall? Leading to too little droop travel?

RF - 14 2/16”
RR - 14 6/16”
LF - 14”
LR - 14 8/16”


Sent from my iPhone using Tapatalk
That's almost stock height in the rear, which I would say yes is too tall!

- Andrew
Racecomp Engineering is offline   Reply With Quote
The Following User Says Thank You to Racecomp Engineering For This Useful Post:
Spuds (09-07-2024)
Old 09-06-2024, 03:43 PM   #63
Tomyyyu
Member
 
Join Date: May 2023
Drives:
Posts: 79
Thanks: 19
Thanked 21 Times in 17 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by Racecomp Engineering View Post
That's almost stock height in the rear, which I would say yes is too tall!

- Andrew

Gotcha. So I got it corner balanced to follow my heights of 140mm front and around 145-155mm rear. That’s from floor to pinch weld.

Wondering if it makes sense to just leave it as is for now, what would you recommend? Corner balanced weights attached. Since the rear was raised to get my cross weights correct.


Sent from my iPhone using Tapatalk
Tomyyyu is offline   Reply With Quote
Old 09-06-2024, 04:24 PM   #64
cmiovino
Senior Member
 
cmiovino's Avatar
 
Join Date: Aug 2020
Drives: 2017 BRZ PP, 2004 WRX
Location: Pittsburgh
Posts: 407
Thanks: 33
Thanked 303 Times in 186 Posts
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by Tomyyyu View Post
@ Went ahead and measured my center of wheel to fender and ended up with these heights. Are these too tall? Leading to too little droop travel?

RF - 14 2/16”
RR - 14 6/16”
LF - 14”
LR - 14 8/16”

Sent from my iPhone using Tapatalk
You'll have the same issue I had earlier this year doing the same thing. it'll ride "ok" on the street, but at speed, like autocross or track, you'll be lifting the year tires up constantly. Your RPMs will be shooting up to redline putting any power down out of turns. The rear will also hop around a lot.

My height with issues (center hub to fender):

Front 13 1/4"
Rear 14 1/4"

My height after lowering and allowing more droop travel (drives great now):

Front 12 3/4" ("one finger gap")

Rear 13 1/4" ("two finger gap")

It sounds like you're literally 2" too high in the front and at least an 1" in the rear.
__________________
2017 BRZ Limited Performance Pack - Steel Cities Region SCCA / North Hills Sports Car Club
cmiovino is offline   Reply With Quote
Old 09-06-2024, 04:26 PM   #65
ZDan
Senior Member
 
ZDan's Avatar
 
Join Date: May 2011
Drives: '23 BRZ
Location: Providence, RI
Posts: 4,634
Thanks: 1,417
Thanked 3,963 Times in 2,071 Posts
Mentioned: 85 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by Tomyyyu View Post
@ Went ahead and measured my center of wheel to fender and ended up with these heights. Are these too tall? Leading to too little droop travel?

RF - 14 2/16”
RR - 14 6/16”
LF - 14”
LR - 14 8/16”
A bit on the high side, I'm about 1" lower all around. That said, *if* you are bottoming the outside front you might need to run higher...

You might run it as it is and assess the handling situation, then lower all four corners about 12mm or 1/2" and see what that does to handling and balance, and go from there.
ZDan is offline   Reply With Quote
Old 09-06-2024, 04:27 PM   #66
Tomyyyu
Member
 
Join Date: May 2023
Drives:
Posts: 79
Thanks: 19
Thanked 21 Times in 17 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by ZDan View Post
A bit on the high side, I'm about 1" lower all around. That said, *if* you are bottoming the outside front you might need to run higher...

You might run it as it is and assess the handling situation, then lower all four corners about 12mm or 1/2" and see what that does to handling and balance, and go from there.

Yeah, my plan is probably to run it as is. Then make adjustments. Since technically I still haven’t ran it yet.


Sent from my iPhone using Tapatalk
Tomyyyu is offline   Reply With Quote
The Following User Says Thank You to Tomyyyu For This Useful Post:
ZDan (09-06-2024)
Old 09-06-2024, 04:27 PM   #67
Tomyyyu
Member
 
Join Date: May 2023
Drives:
Posts: 79
Thanks: 19
Thanked 21 Times in 17 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by cmiovino View Post
You'll have the same issue I had earlier this year doing the same thing. it'll ride "ok" on the street, but at speed, like autocross or track, you'll be lifting the year tires up constantly. Your RPMs will be shooting up to redline putting any power down out of turns. The rear will also hop around a lot.

My height with issues (center hub to fender):

Front 13 1/4"
Rear 14 1/4"

My height after lowering and allowing more droop travel (drives great now):

Front 12 3/4" ("one finger gap")

Rear 13 1/4" ("two finger gap")

It sounds like you're literally 2" too high in the front and at least an 1" in the rear.

What is your setup? That will help paint a better picture.


Sent from my iPhone using Tapatalk
Tomyyyu is offline   Reply With Quote
Old 09-06-2024, 06:22 PM   #68
cmiovino
Senior Member
 
cmiovino's Avatar
 
Join Date: Aug 2020
Drives: 2017 BRZ PP, 2004 WRX
Location: Pittsburgh
Posts: 407
Thanks: 33
Thanked 303 Times in 186 Posts
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by Tomyyyu View Post
What is your setup? That will help paint a better picture.


Sent from my iPhone using Tapatalk
RCE SS-1's (6k springs, even), with their camber plates up front, OEM ones in the rear.

Vorshlag vs RCE/KW camber plates won't make a huge difference in height between the two, comparing the two setups in terms of height should be very much the same.
__________________
2017 BRZ Limited Performance Pack - Steel Cities Region SCCA / North Hills Sports Car Club
cmiovino is offline   Reply With Quote
Old 09-06-2024, 06:40 PM   #69
Tomyyyu
Member
 
Join Date: May 2023
Drives:
Posts: 79
Thanks: 19
Thanked 21 Times in 17 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by cmiovino View Post
RCE SS-1's (6k springs, even), with their camber plates up front, OEM ones in the rear.

Vorshlag vs RCE/KW camber plates won't make a huge difference in height between the two, comparing the two setups in terms of height should be very much the same.

Yeah comparing two different things. So I’ll just have to see how it works out, lol.


Sent from my iPhone using Tapatalk
Tomyyyu is offline   Reply With Quote
Old 09-07-2024, 03:55 AM   #70
strat61caster
-
 
strat61caster's Avatar
 
Join Date: Nov 2012
Drives: '13 FRS - STX
Location: SF Bay Area
Posts: 10,381
Thanks: 13,780
Thanked 9,499 Times in 5,011 Posts
Mentioned: 94 Post(s)
Tagged: 3 Thread(s)
949’s ride height suggestions have a lot to do with their damper design droop/bump lengths, it shouldn’t be gospel, but I think it’s a great starting point.

@Spuds do you have the big oem tapered bolt in the upper hole of your strut? You have to use some level of camber bolt, even just the smaller oe bottom bolt to get past -4 degrees of camber even when the struts are slotted.
__________________
Quote:
Originally Posted by Guff View Post
ineedyourdiddly
strat61caster is offline   Reply With Quote
The Following User Says Thank You to strat61caster For This Useful Post:
Spuds (09-07-2024)
 
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Understeer on '22 BRZ Fletch Tracking / Autocross / HPDE / Drifting 29 12-20-2022 10:09 PM
oversteer and understeer orc BRZ Second-Gen (2022+) -- General Topics 76 10-05-2021 04:08 PM
Why does car understeer when going downhill? hpde_addict Tracking / Autocross / HPDE / Drifting 20 01-15-2018 10:42 AM
Understeer after new wheels carsebuco Wheels | Tires | Spacers | Hub -- Sponsored by The Tire Rack 16 12-04-2017 06:49 PM
understeer on 17 brz alex.s Suspension | Chassis | Brakes -- Sponsored by 949 Racing 37 09-11-2017 05:05 AM


All times are GMT -4. The time now is 07:23 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
User Alert System provided by Advanced User Tagging v3.3.0 (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.

Garage vBulletin Plugins by Drive Thru Online, Inc.