|
Cosmetic Modification (Interior/Exterior/Lighting) Discussions about cosmetic mods. |
![]() |
|
Thread Tools | Search this Thread |
![]() |
#589 |
Senior Member
Join Date: Aug 2019
Drives: BRZ
Location: Connecticut
Posts: 198
Thanks: 47
Thanked 26 Times in 24 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
I can take some pictures with the measurements later, but I'd highly recommend just finding a trunk that's already got the holes in it and swapping it on. Seems there's always someone with a spoiler who doesn't want one or there's a recently totaled car being parted out (check car-part.com too).
|
![]() |
![]() |
The Following User Says Thank You to ThatYeti For This Useful Post: | FR-S2GT86 (10-21-2021) |
![]() |
#590 | |
Member
Join Date: Apr 2020
Drives: 2019 Toyota 86
Location: Arlington, VA
Posts: 25
Thanks: 6
Thanked 8 Times in 8 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Sent from my ONEPLUS A6003 using Tapatalk |
|
![]() |
![]() |
The Following User Says Thank You to markubiak For This Useful Post: | FR-S2GT86 (10-21-2021) |
![]() |
#591 | |
Master Collaborator
Join Date: Nov 2019
Drives: Was '15 FR-S, 6MT, Now '15 GT86
Location: West Virginia, USA
Posts: 1,415
Thanks: 211
Thanked 999 Times in 605 Posts
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
|
Quote:
|
|
![]() |
![]() |
![]() |
#592 | |
Master Collaborator
Join Date: Nov 2019
Drives: Was '15 FR-S, 6MT, Now '15 GT86
Location: West Virginia, USA
Posts: 1,415
Thanks: 211
Thanked 999 Times in 605 Posts
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Understood. Break them off, remove the center section from each end and get a special piece 3D printed and painted to reinstall. Shouldn't be too difficult. Thanks. |
|
![]() |
![]() |
![]() |
#593 |
Senior Member
Join Date: Aug 2019
Drives: BRZ
Location: Connecticut
Posts: 198
Thanks: 47
Thanked 26 Times in 24 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
Not sure how helpful these will be but here you go:
|
![]() |
![]() |
![]() |
#594 |
Master Collaborator
Join Date: Nov 2019
Drives: Was '15 FR-S, 6MT, Now '15 GT86
Location: West Virginia, USA
Posts: 1,415
Thanks: 211
Thanked 999 Times in 605 Posts
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
|
I'll try and make that work. I'm going to measure where I have them sitting right now using a dial caliper which will be more accurate, and I'll post those measurements later. Thanks. |
![]() |
![]() |
![]() |
#595 |
Senior Member
Join Date: Aug 2019
Drives: BRZ
Location: Connecticut
Posts: 198
Thanks: 47
Thanked 26 Times in 24 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
Might be better off trying to find a cad drawing for the stock trunk since they're meant to use stock holes
|
![]() |
![]() |
![]() |
#596 |
Master Collaborator
Join Date: Nov 2019
Drives: Was '15 FR-S, 6MT, Now '15 GT86
Location: West Virginia, USA
Posts: 1,415
Thanks: 211
Thanked 999 Times in 605 Posts
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
|
@ThatYeti
Alright, as I compare your tape measure pictures to mine at just about the same angle that you snapped your pictures, it would appear as if I need to begin grinding out the forward stud hole towards the passenger side a little bit to result in about a half inch of movement from the forward "point" of the risor base in the direction of the trunk lid edge. The rearward stud hole looks to be in the perfect position. Here are the measurements that I took with my dial caliper, I measure 2-19/64" from the forward "point" of the risor base to the edge of the trunk lid at a right angle, and 55/64" from the rear "corner" of the risor base to the edge of the trunk lid right where the downward slope begins. If you or anyone else can take the same measurements that I did using a dial caliper and post those measurements, I would really appreciate it. Thanks for helping me get this far. |
![]() |
![]() |
![]() |
#597 |
Senior Member
Join Date: Aug 2019
Drives: BRZ
Location: Connecticut
Posts: 198
Thanks: 47
Thanked 26 Times in 24 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
Not sure it's the same angle but did the best I could
|
![]() |
![]() |
![]() |
#598 |
Master Collaborator
Join Date: Nov 2019
Drives: Was '15 FR-S, 6MT, Now '15 GT86
Location: West Virginia, USA
Posts: 1,415
Thanks: 211
Thanked 999 Times in 605 Posts
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
|
Looks like a 7/16" difference between your forward measurement and mine, which I estimated pretty close using the tape measure at 1/2". Thanks for your help. |
![]() |
![]() |
|
|
![]() |
Tags |
removal, spoiler, trunk, wing |
Thread Tools | Search this Thread |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Remove trunk spoiler clips? | Drambeenie | Member's Car Journals | 0 | 05-10-2017 12:31 AM |
2017 BRZ Limited Spoiler | Chayce808 | Cosmetic Modification (Interior/Exterior/Lighting) | 6 | 01-04-2017 01:49 AM |
2017 BRZ without spoiler? | vroomvroom1 | BRZ First-Gen (2012+) -- General Topics | 9 | 07-18-2016 11:46 AM |
Remove spoiler for Rocket Bunny one? | xrinnenganx | Cosmetic Modification (Interior/Exterior/Lighting) | 7 | 10-21-2014 11:28 AM |
Is there a way to remove the spoiler? | rapier7 | BRZ First-Gen (2012+) -- General Topics | 15 | 08-21-2013 11:58 PM |