OLM Headlight issues - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

FineVisionz · 11-16-2021, 10:46 AM

Hello,

I just got my OLM headlights with HID's yesterday. I test tested them out and everything worked fine. Later that evening I go to fully install them and everything but the high and low beams work. The boomerang and turn signals work just fine.

I was thinking that maybe I blew a fuse but I plugged back in the stock headlights and they worked just fine.

Any suggestions would be greatly appreciated.

How I have my Ballast connected to the headlight;
https://imgur.com/stiINfa

Then the other two connectors just plugged into the car's headlight harnesses;
https://imgur.com/ruyvwnH

Edit: I've connected a voltmeter to the plug that comes out of the headlight and plugs into the ballast and it reads that is has power when the headlights are turned on, but for some reason the power isnt making it through the ballast. I'm kinda confused because it was working before and now it's not. Also, neither side are working. So I'm not too sure what the likely hood of BOTH ballasts being pretty much DOA is but I imagine it isn't very high, lol.

Drifter X · 11-16-2021, 10:12 PM

Flip the harness leading into the ballast.

Sent from my iPhone using Tapatalk

x808drifter · 11-17-2021, 02:13 AM

Quote:

Originally Posted by Drifter X

Flip the harness leading into the ballast.

Sent from my iPhone using Tapatalk

If not that Ballast is DOA probably

Drifter X · 11-17-2021, 11:09 AM

Quote:

Originally Posted by x808drifter

If not that Ballast is DOA probably

Chee hee

Sent from my iPhone using Tapatalk

FineVisionz · 11-18-2021, 11:16 AM

Quote:

Originally Posted by Drifter X

Flip the harness leading into the ballast.

Sent from my iPhone using Tapatalk

Holy shit, I'm so dumb. This worked, thank you so much.

To be fair, the design for the plug is also kinda dumb. It has a tab on either side for the male side to clip onto allowing you to plug it in backwards. (if that makes sense)

I first read this message and I thought, "No way this can be done"

Haha, thanks for pointing out the obvious for me, lol.

Cheers

Drifter X · 11-18-2021, 01:43 PM

No worries. The harnesses are like that on a lot of HID kits. I’ve made that mistake on both my wife’s Camry and my 86. I thought the same thing. “Could it be that the harness is flipped?… fuck me holy shit it worked!” Lol.

Sent from my iPhone using Tapatalk

11-16-2021, 10:46 AM	#1
FineVisionz Member Join Date: Aug 2018 Drives: Series.Blue Location: Arizona Posts: 46 Thanks: 4 Thanked 11 Times in 7 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	OLM Headlight issues Hello, I just got my OLM headlights with HID's yesterday. I test tested them out and everything worked fine. Later that evening I go to fully install them and everything but the high and low beams work. The boomerang and turn signals work just fine. I was thinking that maybe I blew a fuse but I plugged back in the stock headlights and they worked just fine. Any suggestions would be greatly appreciated. How I have my Ballast connected to the headlight; https://imgur.com/stiINfa Then the other two connectors just plugged into the car's headlight harnesses; https://imgur.com/ruyvwnH Edit: I've connected a voltmeter to the plug that comes out of the headlight and plugs into the ballast and it reads that is has power when the headlights are turned on, but for some reason the power isnt making it through the ballast. I'm kinda confused because it was working before and now it's not. Also, neither side are working. So I'm not too sure what the likely hood of BOTH ballasts being pretty much DOA is but I imagine it isn't very high, lol. Last edited by FineVisionz; 11-16-2021 at 12:04 PM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
BRZ headlight shroud inside FRS headlight?	S84kam	Cosmetic Modification (Interior/Exterior/Lighting)	9	04-02-2016 12:24 AM
Winjet headlight signal issues	Demotic	Cosmetic Modification (Interior/Exterior/Lighting)	0	09-21-2015 11:03 PM
Monogram headlight issues	Simon	Cosmetic Modification (Interior/Exterior/Lighting)	8	10-28-2014 10:48 AM
HID Headlight Issues	KkSc	Cosmetic Modification (Interior/Exterior/Lighting)	5	02-10-2014 04:23 PM
WTB Stock headlight projectors from retrofit OR a broken headlight	official_george	Exterior Parts (Aero, Lighting, Etc.)	3	12-02-2013 03:32 PM

11-16-2021, 10:12 PM	#2
Drifter X Senior Member Join Date: Dec 2018 Drives: 2019 Toyota 86 TRD SE Location: Honolulu Posts: 235 Thanks: 160 Thanked 86 Times in 71 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	Flip the harness leading into the ballast. Sent from my iPhone using Tapatalk

11-18-2021, 01:43 PM	#6
Drifter X Senior Member Join Date: Dec 2018 Drives: 2019 Toyota 86 TRD SE Location: Honolulu Posts: 235 Thanks: 160 Thanked 86 Times in 71 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	No worries. The harnesses are like that on a lot of HID kits. I’ve made that mistake on both my wife’s Camry and my 86. I thought the same thing. “Could it be that the harness is flipped?… fuck me holy shit it worked!” Lol. Sent from my iPhone using Tapatalk

User Name		Remember Me?
Password