10-23-2019, 11:09 AM | #211 |
Senior Member
Join Date: Aug 2014
Drives: 2013 FR-S
Location: Northwest Iowa
Posts: 7,354
Thanks: 454
Thanked 4,542 Times in 2,947 Posts
Mentioned: 59 Post(s)
Tagged: 5 Thread(s)
|
I actually have a computer and harness. It's the canbus module cost and what I'll lose on the Hydra but at this point I guess I don't really care about that if it fixes my problem. I assuming it's tune related, then someone familiar with LS tuning should be able to figure it out pretty quick. It's not like the Hydra uses a different language. It seems it's out of my league though. Maybe I should call some local shops. I know one shop 2 hours away advertises a "complete tuning service" including idle and cranking
|
10-23-2019, 11:35 AM | #212 | |
Senior Member
Join Date: Apr 2019
Drives: 86, 981S, RX8, 2500HD, GenesisV8
Location: Palmer Motorsports
Posts: 119
Thanks: 82
Thanked 70 Times in 43 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
Quote:
The tuning is similar, but requires their own proprietary software. Borrowing somebody else's tune is a good test to point you in the right direction. |
|
10-23-2019, 11:51 AM | #213 |
Senior Member
Join Date: Aug 2014
Drives: 2013 FR-S
Location: Northwest Iowa
Posts: 7,354
Thanks: 454
Thanked 4,542 Times in 2,947 Posts
Mentioned: 59 Post(s)
Tagged: 5 Thread(s)
|
What's the MRS module run at now? I don't want to figure out programming
|
10-23-2019, 01:56 PM | #214 |
Senior Member
Join Date: Apr 2014
Drives: 2013 Ultramarine FR-S
Location: Springfield, MO
Posts: 1,944
Thanks: 2,534
Thanked 1,392 Times in 800 Posts
Mentioned: 31 Post(s)
Tagged: 3 Thread(s)
|
No longer available. The guy that was working on the project is no longer with the company. They have taken everything for it off their website.
__________________
|
10-23-2019, 02:01 PM | #215 |
Senior Member
Join Date: Aug 2014
Drives: 2013 FR-S
Location: Northwest Iowa
Posts: 7,354
Thanks: 454
Thanked 4,542 Times in 2,947 Posts
Mentioned: 59 Post(s)
Tagged: 5 Thread(s)
|
|
10-23-2019, 02:52 PM | #216 | |
I Love custom Turbo kits
Join Date: Mar 2012
Drives: Limited BRZ
Location: Miami
Posts: 10,770
Thanks: 20,004
Thanked 8,343 Times in 4,361 Posts
Mentioned: 441 Post(s)
Tagged: 12 Thread(s)
|
Quote:
__________________
|
|
10-23-2019, 03:02 PM | #217 |
Senior Member
Join Date: Aug 2014
Drives: 2013 FR-S
Location: Northwest Iowa
Posts: 7,354
Thanks: 454
Thanked 4,542 Times in 2,947 Posts
Mentioned: 59 Post(s)
Tagged: 5 Thread(s)
|
|
10-23-2019, 08:04 PM | #218 |
Senior Member
Join Date: Jul 2014
Drives: 14 BSP Edelbrock BRZ
Location: Lon Gisland
Posts: 806
Thanks: 113
Thanked 450 Times in 256 Posts
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
|
I can't see how a tuning issue gives you a random result of 1 of 4 outcomes when you try to start it. That screams intermittent electrical issue to me.
|
10-23-2019, 08:09 PM | #219 |
Senior Member
Join Date: Aug 2014
Drives: 2013 FR-S
Location: Northwest Iowa
Posts: 7,354
Thanks: 454
Thanked 4,542 Times in 2,947 Posts
Mentioned: 59 Post(s)
Tagged: 5 Thread(s)
|
|
12-01-2019, 12:51 PM | #220 |
Senior Member
Join Date: Aug 2014
Drives: 2013 FR-S
Location: Northwest Iowa
Posts: 7,354
Thanks: 454
Thanked 4,542 Times in 2,947 Posts
Mentioned: 59 Post(s)
Tagged: 5 Thread(s)
|
Confirmed you can drop the transmission with the motor "in" the car, if you drop the subframe.
Flywheel is coming out for ring gear service since the starter broke off half the teeth on it. Hydra EMS is going in for service too since the MAP reads higher than it should. Also on the list is wiring the cam sensor for more accurate crank position information. I'm replacing the crank sensor too just in case |
06-18-2020, 08:42 AM | #221 |
Senior Member
Join Date: Aug 2014
Drives: 2013 FR-S
Location: Northwest Iowa
Posts: 7,354
Thanks: 454
Thanked 4,542 Times in 2,947 Posts
Mentioned: 59 Post(s)
Tagged: 5 Thread(s)
|
Been a while but I'll give a short update.
Had a problem with the shifter bit going into gear from a stop. Also getting locked out of gears at high RPM. Appears to have been caused by a misadjusted clutch pedal. So if you're having shifting problems check that first! I've almost got all the bugs worked out. Synced up the cam sensor so now it starts every time I turn the key! So excited to have that fixed. However, according to my timing light, my timing is right at idle but gets way way off at any other rpm. This may just be because I'm not familiar with how the timing light should look with the Wasted Spark firing system (cylinders fire in opposing pairs). So cylinder 1 fires once for ignition and again when #5 or whichever ignites. The timing light will then flash again at who knows what angle. We will be rewiring the ignition for sequential firing soon. This is the last hurdle to pass before this swap is "done". I am leaning towards adding a turbo in the future but who knows when that will be. Air conditioning does work, I'll be posting about that soon Sent from my ONEPLUS A5010 using Tapatalk |
06-18-2020, 09:14 AM | #222 | |
Member
Join Date: Aug 2017
Drives: Red BRZ
Location: North Carolina
Posts: 66
Thanks: 1
Thanked 16 Times in 10 Posts
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Sent from my SM-G950U using Tapatalk |
|
06-18-2020, 09:21 AM | #223 | |
Senior Member
Join Date: Aug 2014
Drives: 2013 FR-S
Location: Northwest Iowa
Posts: 7,354
Thanks: 454
Thanked 4,542 Times in 2,947 Posts
Mentioned: 59 Post(s)
Tagged: 5 Thread(s)
|
Quote:
Sent from my ONEPLUS A5010 using Tapatalk |
|
07-27-2020, 08:49 PM | #224 |
Senior Member
Join Date: Aug 2014
Drives: 2013 FR-S
Location: Northwest Iowa
Posts: 7,354
Thanks: 454
Thanked 4,542 Times in 2,947 Posts
Mentioned: 59 Post(s)
Tagged: 5 Thread(s)
|
My pilot bearing failed so I'm replacing it and my slave. Got a heavy duty Ram slave unit.
FYI. If you are using a T56 you need the smaller needle bearing style pilot bearing. If you are using a TR6060 you need the much larger sealed ball bearing unit. BEWARE! There are 2 sizes of the larger pilot. One for aftermarket cranks and one for stock cranks. Of course I got the wrong one from Summit. That's how I found out about the multiple sizes. Also, there is an extended needle bearing unit if you feel you need that Sent from my ONEPLUS A5010 using Tapatalk |
|
|
Thread Tools | Search this Thread |
|
|