|
Cosmetic Modification (Interior/Exterior/Lighting) Discussions about cosmetic mods. |
|
Thread Tools | Search this Thread |
03-12-2020, 08:06 PM | #1 |
Senior Member
Join Date: May 2015
Drives: 2013 BRZ Limited
Location: Atlanta, GA
Posts: 123
Thanks: 115
Thanked 48 Times in 32 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Removing A-Pillar completely (green plastic retainer question)
I have a rattle from behind my passenger side A-pillar, I’d previously put weatherstripping on the bottom of it and it helped buy something behind it is causing the rattle. I tried to remove the plastic green retainer but couldn’t so I left it attached.
So I need to completely remove the a-pillar this time, remove that plastic green retainer. But I’m concerned about setting off the airbag (I’ll disconnect the battery for 30 mins first) and also not being able to get that green plastic retainer back in place. I found this post with was helpful https://www.ft86club.com/forums/showthread.php?t=54683 Has anyone ever removed the pillar before, any advice on how to deal with the green plastic retainer?
__________________
|
03-12-2020, 08:21 PM | #2 |
Rust bucket enthusiast
Join Date: Feb 2017
Drives: 2013 Turbo Firestorm FRS
Location: Vermont
Posts: 3,934
Thanks: 3,200
Thanked 4,095 Times in 2,045 Posts
Mentioned: 31 Post(s)
Tagged: 0 Thread(s)
|
Why worry about the green leash? Just swing the a-pillar plastic around with it connected until you've fixed whatever your noise is. The leash is just to prevent you getting hit by the plastic if the curtain airbag goes off.
I've removed my a-pillar and put it back without undoing the green leash |
03-12-2020, 09:15 PM | #3 |
Senior Member
Join Date: Mar 2017
Drives: Q5 + BRZ + M796
Location: Santa Rosa, CA
Posts: 7,884
Thanks: 5,668
Thanked 5,805 Times in 3,299 Posts
Mentioned: 70 Post(s)
Tagged: 0 Thread(s)
|
Agreed, and I was specifically doing this to apply foam filler to remove a rattle too.
__________________
My Build | K24 Turbo Swap | *K24T BRZ SOLD*
|
03-13-2020, 12:22 AM | #4 | |
Senior Member
Join Date: Jan 2013
Drives: Toyota 86
Location: South Korea
Posts: 267
Thanks: 127
Thanked 201 Times in 115 Posts
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
|
Quote:
__________________
/* Custom underbody panels and diffuser
Custom electric water pump and PWM controller HKS GT EL header, 17MY intake manifold */ |
|
03-13-2020, 05:23 PM | #5 |
Senior Member
Join Date: Jul 2014
Drives: 2013 Firestorm FR-S AT
Location: Smokey Mountains
Posts: 404
Thanks: 54
Thanked 261 Times in 138 Posts
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
|
I had to remove the panel completely to run my rd's power wire to the 12V socket. The green plastic retainer is a bitch to remove and replace. I used needle nose pliers to turn it 90 degrees. DO NOT remove it if you don't have to.
|
The Following User Says Thank You to RickyBobby For This Useful Post: | Suparu (03-16-2020) |
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Removing Passenger Side Pillar | Mcdj18 | Cosmetic Modification (Interior/Exterior/Lighting) | 6 | 10-29-2016 03:39 PM |
A/C completely shut off... | Scikotic | Issues | Warranty | Recalls / TSB | 6 | 08-01-2015 04:28 PM |
How To Completely Rebadge Your FR-S | tbwoodlee | Cosmetic Modification (Interior/Exterior/Lighting) | 62 | 05-07-2015 11:55 PM |