DIY – OEM Heated Seats - Page 2 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

@Art_Mighty · 10-13-2016, 01:37 AM

Quote:

Originally Posted by Figo

thank you for your thread!

Do you have any suggestion if I only need to swap seat to base FRS but do not need the heating funciton?

Iv heard that the BRZ limited seats are not direct fit. There will be sensor issue?

At least when I did mine they were...

Figo · 10-13-2016, 11:23 AM

Quote:

Originally Posted by @Art_Mighty

At least when I did mine they were...

Hah, that's why I pmed you.

You are probably the only one in the forum who install the BRZ limited seats without any issue. Everyone else has the issue. So I am wondering that did you do anything special? haha.

3ndagor · 07-22-2018, 06:19 PM

I did the swap of seats too ... ( as of all interior as well for fact ) but anyways

got the pressure sensor going off and on ( like it works when someone is seated but I get the code when I'm alone in the car )

any way to clear that code?

thanks for the DYI... I'm heading on to doing this before the winter

Twitchy313 · 03-28-2019, 07:13 PM

Quote:

Originally Posted by RojerLockless

*opens the thread* Oh sweet I'd love heated seats! *sees all the pictures of wires* Well.. screw that

lol

Ghostcloak · 08-05-2020, 03:43 PM

Quote:

Originally Posted by lbroskee

@@Art_Mighty what do you recommend if i can't get the connectors? or would you know the part numbers for them? I'm looking into this but since won't b able to source easily i need to improvise

So. Just in case anyone is trying to find this information still.

The blue male connector attached to the heated seat is a 4 position (090 type) TS series with OEM Toyota part number 90980-11765. The wire harness female white connector side is OEM Toyota part number 90980-11766. It is discontinued. I haven't confirmed with my own experience yet, however I believe the correct female terminal is going to be a 2.3 II (series 090 II) female terminal.

There is also a strong similarity with the Sumutomo TS series part number Conn-100800 and housing Conn-100325. Yazaki 7116-4026 looks to be the same female terminal.

There is a . PDF here that gives some technical info on the two connectors: toyota-tech.eu/wire_harness_rm/RM06H0E.pdf

Ghostcloak · 09-09-2020, 05:21 PM

Parts worked! Confirmed that the heated seats are the same as the rear tail light 4pin connector.

Use:
Sumutomo TS series part number Conn-100800 and housing Conn-100325

Cridland · 10-28-2020, 09:54 PM

Sorry to revive this thread, long time member lol and got some BRZ seats for my tacoma and installing those here shortly and using this wiring schematic. Thanks a ton!!

Quick question, you are not using a relay are you? Just 12v from the fuse panel to the switch, and then from the switch to either the hi or lo heater wire. You are letting all 10A (max) run through the switch eh?

Ghostcloak · 11-25-2020, 10:42 AM

That is correct Cridland. I am using the oem switches, so they are rated for this current load. If you are using an aftermarket switch, I recommend getting a 15amp rated single pole double throw switch (safety factor) or going to relay route.

Twitchy313 · 12-30-2020, 05:38 AM

Super late to the party, but awesome job!

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
heated seats	debs0712	Cosmetic Modification (Interior/Exterior/Lighting)	47	04-08-2018 09:06 PM
brz limited heated seats	abutterman	Issues \| Warranty \| Recalls / TSB	15	04-15-2013 11:18 AM
heated seats installation	abutterman	Electronics \| Audio \| NAV \| Infotainment	10	02-15-2013 04:19 PM
Heated seats: Switches backlit?	Augora	Issues \| Warranty \| Recalls / TSB	3	01-15-2013 02:51 AM
Retrofit heated seats to Premium?	blalor	BRZ First-Gen (2012+) -- General Topics	4	05-31-2012 07:50 AM

09-09-2020, 05:21 PM	#20
Ghostcloak Junior Member Join Date: Aug 2020 Drives: 2019 86 TRD SE Location: USA Posts: 3 Thanks: 0 Thanked 1 Time in 1 Post Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Parts worked! Confirmed that the heated seats are the same as the rear tail light 4pin connector. Use: Sumutomo TS series part number Conn-100800 and housing Conn-100325

10-28-2020, 09:54 PM	#21
Cridland Senior Member Join Date: Mar 2013 Drives: 2013 Whiteout FRS Location: Alberta, Canada Posts: 123 Thanks: 39 Thanked 31 Times in 27 Posts Mentioned: 4 Post(s) Tagged: 0 Thread(s)	Sorry to revive this thread, long time member lol and got some BRZ seats for my tacoma and installing those here shortly and using this wiring schematic. Thanks a ton!! Quick question, you are not using a relay are you? Just 12v from the fuse panel to the switch, and then from the switch to either the hi or lo heater wire. You are letting all 10A (max) run through the switch eh?

11-25-2020, 10:42 AM	#22
Ghostcloak Junior Member Join Date: Aug 2020 Drives: 2019 86 TRD SE Location: USA Posts: 3 Thanks: 0 Thanked 1 Time in 1 Post Mentioned: 0 Post(s) Tagged: 0 Thread(s)	That is correct Cridland. I am using the oem switches, so they are rated for this current load. If you are using an aftermarket switch, I recommend getting a 15amp rated single pole double throw switch (safety factor) or going to relay route.

12-30-2020, 05:38 AM	#23
Twitchy313 Senior Member Join Date: Apr 2017 Drives: 2014 Scion FR-S Location: Los Angeles, California Posts: 103 Thanks: 76 Thanked 15 Times in 14 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	Super late to the party, but awesome job!

User Name		Remember Me?
Password