Jackson Racing Supercharger Owners Thread

[dkstylezz]

Seems like people are not receiving the full kit they should be getting. For the people missing their oil cooler, are you also missing the ecutek? Thanks.

[Jmonty]

Originally Posted by dkstylezz

Seems like people are not receiving the full kit they should be getting. For the people missing their oil cooler, are you also missing the ecutek? Thanks.

Mine was the tuner kit

[2ndgenhachi]

I ordered the CARB kit and got my ecutek. The sc kit was complete there just no oil cooler. I'm guessing it was simply an oversight.

[lastexile1987]

Oil cooler is an optional add on and does not come with the carb kit automatically

I believe it is an additional $695

[Germanjap]

Is there something I'm missing for placing the front bumper back on after installing the supercharger? I spent the last three hours trying to fit it back on and it will not go. Have to get some sleep before work tomorrow and was hoping there were some suggestions if others had problems with the bumper before I tackle it after work tomorrow. Thanks in advance.

[CSG Mike]

Originally Posted by Germanjap

Is there something I'm missing for placing the front bumper back on after installing the supercharger? I spent the last three hours trying to fit it back on and it will not go. Have to get some sleep before work tomorrow and was hoping there were some suggestions if others had problems with the bumper before I tackle it after work tomorrow. Thanks in advance.

Did you take the air guides off of the front bumper? 3 screws each for 2 guides, on either side of the front bumper opening.

[2ndgenhachi]

For all those that installed this kit themselves. How did you prime the sc? I know the rotrex guide says supply pressurized air no more than 15 psi. But how did u gauge the psi of your air gun? Trying to get any tips before I tackle my install.

[The_Understated]

Originally Posted by 2ndgenhachi

For all those that installed this kit themselves. How did you prime the sc? I know the rotrex guide says supply pressurized air no more than 15 psi. But how did u gauge the psi of your air gun? Trying to get any tips before I tackle my install.

Depending on the plumbing of your compressor setup, just install a ball valve and a gauage after it to a quick disconnect at both ends:

[::]======(O)=======//========[::]>-------- [::]========...

^female.........^guage........^ball valve......^male........ ^your original
connector......................................... ........connector.....line

The valve will let you "regulate" the air and the guage to measure the pressure you get. At least that's the cheap way to do it. Unless your compressor already has an adjustable regulator built in.

[uRBAN_Metal]

Originally Posted by Germanjap

Is there something I'm missing for placing the front bumper back on after installing the supercharger? I spent the last three hours trying to fit it back on and it will not go. Have to get some sleep before work tomorrow and was hoping there were some suggestions if others had problems with the bumper before I tackle it after work tomorrow. Thanks in advance.

The bumper is a bitch. I found that when I had problems, the holes on the underside weren't lining up right. Once I got the bottom lined up, the top and sides popped right in perfectly.

Originally Posted by 2ndgenhachi

For all those that installed this kit themselves. How did you prime the sc? I know the rotrex guide says supply pressurized air no more than 15 psi. But how did u gauge the psi of your air gun? Trying to get any tips before I tackle my install.

You either need a air pressure regulator on the output of your compressor, or only fill your compressor to 15psi.

[enivid]

Originally Posted by Germanjap

Is there something I'm missing for placing the front bumper back on after installing the supercharger? I spent the last three hours trying to fit it back on and it will not go. Have to get some sleep before work tomorrow and was hoping there were some suggestions if others had problems with the bumper before I tackle it after work tomorrow. Thanks in advance.

If you have fog lights, you have to make sure the drivers side intercooler pipe is not touching it. You can leave the under body panels off when putting the bumper on. Then you can look underneath the car to see if anything is touching the bumper.

[enivid]

Originally Posted by 2ndgenhachi

For all those that installed this kit themselves. How did you prime the sc? I know the rotrex guide says supply pressurized air no more than 15 psi. But how did u gauge the psi of your air gun? Trying to get any tips before I tackle my install.

I used gravity.

[Jackson Racing]

Originally Posted by dkstylezz

Seems like people are not receiving the full kit they should be getting. For the people missing their oil cooler, are you also missing the ecutek? Thanks.

Originally Posted by 2ndgenhachi

I ordered the CARB kit and got my ecutek. The sc kit was complete there just no oil cooler. I'm guessing it was simply an oversight.

Not an oversight.

EcuTek ProECU Programming Kits have been on backorder for a few weeks. We could not wait any longer for them to come back in stock, so we shipped systems with a note letting customers know we will ship their ProECU Programming Kits to them once they are in our hands this week.

Oil Cooler kits ship in separate boxes. In this case, your supercharger system probably came up ready to ship and shipped before your oil cooler.

Congrats on your new systems!

-Oscar Jr.

[dkstylezz]

Got mine today ECUTEK Backorder note and Oil Cooler unfortunately did not come with my kit too. Hope it comes with the ECUTEK.

Oil Cooler came in today 6/9

[Jmonty]

Originally Posted by Jackson Racing

Not an oversight.

EcuTek ProECU Programming Kits have been on backorder for a few weeks. We could not wait any longer for them to come back in stock, so we shipped systems with a note letting customers know we will ship their ProECU Programming Kits to them once they are in our hands this week.

Oil Cooler kits ship in separate boxes. In this case, your supercharger system probably came up ready to ship and shipped before your oil cooler.

Congrats on your new systems!

-Oscar Jr.

My oil cooler is scheduled to be delivered Wednesday