Tein Flex Z Help - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

BRZSteve · 04-29-2017, 07:00 PM

Hey everyone, I recently installed my Tein Flex Z coilovers and noticed the rears were still pretty high up even when fully maxed out. I'm pretty sure these were supposed to drop 3 inches in the back and I don't think I'm near that. There is still a lot of thread left, but it wont lower anymore. I took the bottom cups out and threaded them as much as they went just to be sure. I've been searching for an answer but couldn't find anything. Has anyone else had this problem?

FR-Sky · 04-30-2017, 03:20 AM

I don't have this problem. My setup before is drop 1.3 front and 1.3 rear, and i barely put one finger between my wheel gap. Even I use Tein recommended setup now is still smaller gap than yours. (0.8 front and 0.7 rear).

BRZSteve · 04-30-2017, 10:31 AM

Quote:

Originally Posted by FR-Sky

I don't have this problem. My setup before is drop 1.3 front and 1.3 rear, and i barely put one finger between my wheel gap. Even I use Tein recommended setup now is still smaller gap than yours. (0.8 front and 0.7 rear).

That's weird. What's your wheel/tire setup?

Mackizzle86 · 04-30-2017, 11:53 AM

Are you trying to lower it? Your perches are set higher up.

BRZSteve · 04-30-2017, 11:59 AM

Quote:

Originally Posted by Mackizzle86

Are you trying to lower it? Your perches are set higher up.

Yes I'm trying to lower it a lot more. I never touched the spring perches I just left it factory spec. Wouldn't altering the perches increase/decrease preload?

Trust86 · 04-30-2017, 12:10 PM

If the threads are maxed out, next thing would be rear LCAs. The slight tire stretch makes the gap more noticeable as well.

BRZSteve · 04-30-2017, 12:26 PM

Quote:

Originally Posted by Trust86

If the threads are maxed out, next thing would be rear LCAs. The slight tire stretch makes the gap more noticeable as well.

So it's normal to be this high even when maxed out? I was under the impression that maxed out would be when all the perches were touching, since I have so much thread left.

FR-Sky · 04-30-2017, 03:26 PM

Quote:

Originally Posted by BRZSteve

That's weird. What's your wheel/tire setup?

Its a 255/40/17 with -3 camber, so it wouldn't matter much.
I can put 1 finger front, and about 2 fingers rear.

BRZSteve · 04-30-2017, 03:59 PM

Quote:

Originally Posted by FR-Sky

Its a 255/40/17 with -3 camber, so it wouldn't matter much.
I can put 1 finger front, and about 2 fingers rear.

Yeah my rears are about a 2 finger as well. Just wondering, how much lower are you able to go?

FR-Sky · 04-30-2017, 04:25 PM

Quote:

Originally Posted by BRZSteve

Yeah my rears are about a 2 finger as well. Just wondering, how much lower are you able to go?

I think I can still drop 1 inches more, but I didn't do that due to 255, it will rub.

Kaotic Lazagna · 05-01-2017, 12:36 AM

Maxed out the front (removed the locking rings), and maxed out the rear plus using some pre-load adjustment.

sIowbrz · 05-01-2017, 02:43 PM

Something is wrong my flex z didnt even max out on 18x9.5 +38 is only .5 inch gap i can tuck the tires my rear is -2.3

BRZSteve · 05-01-2017, 05:25 PM

Quote:

Originally Posted by sIowbrz

Something is wrong my flex z didnt even max out on 18x9.5 +38 is only .5 inch gap i can tuck the tires my rear is -2.3

Yeah thats pretty much the same set up as me so idk what went wrong. Here's some more photo's because that angle and ground not being even might of made things look worse. Rears are completely maxed out and fronts are perfect because they have some more room to go lower. Only looking for another 1/2 for the rears.

mav1178 · 05-01-2017, 07:47 PM

Have you considered contacting Tein USA about this?

If the shock body is bottoming out in the lower bracket, they made a design change in production that has obviously impacted the advertised specs.

My Ohlins from 2013 were a similar situation, I suspect they used parts from another platform to reduce some manufacturing costs.

-alex

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Tein Flex A	DeaconRoc	Suspension \| Chassis \| Brakes -- Sponsored by 949 Racing	138	04-12-2018 05:23 AM
Tein Flex A and Z!!!	breadcrumbz	Suspension \| Chassis \| Brakes -- Sponsored by 949 Racing	25	05-24-2016 03:44 PM
Help wanted: Tein Street Flex for $950 or Flex Z or $820?	chezzy79	Suspension \| Chassis \| Brakes -- Sponsored by 949 Racing	5	09-01-2015 09:33 PM
Tein Flex Z	Bigmaxy	Suspension \| Chassis \| Brakes -- Sponsored by 949 Racing	0	01-27-2015 03:22 AM
FS: (SOLD) Tein SRC / Tein Flex / Cusco F&R Sway / Cusco F&R Strut	kvnchu	Brakes, Suspension, Chassis	26	12-09-2013 01:10 PM

04-30-2017, 03:20 AM	#2
FR-Sky Senior Member Join Date: Dec 2015 Drives: 2013 FR-S 10 series [755] Location: Bay Area, CA Posts: 1,189 Thanks: 385 Thanked 390 Times in 264 Posts Mentioned: 7 Post(s) Tagged: 2 Thread(s)	I don't have this problem. My setup before is drop 1.3 front and 1.3 rear, and i barely put one finger between my wheel gap. Even I use Tein recommended setup now is still smaller gap than yours. (0.8 front and 0.7 rear).

04-30-2017, 11:53 AM	#4
Mackizzle86 Member Join Date: Feb 2017 Drives: FR-S Location: Florida Posts: 53 Thanks: 10 Thanked 36 Times in 23 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Are you trying to lower it? Your perches are set higher up.

04-30-2017, 12:10 PM	#6
Trust86 Senior Member Join Date: Sep 2015 Drives: 2016 Halo FRS Location: US Posts: 414 Thanks: 290 Thanked 162 Times in 106 Posts Mentioned: 8 Post(s) Tagged: 0 Thread(s)	If the threads are maxed out, next thing would be rear LCAs. The slight tire stretch makes the gap more noticeable as well.

05-01-2017, 12:36 AM	#11
Kaotic Lazagna Senior Member Join Date: Apr 2014 Drives: GR Corolla Location: Lathrop, CA Posts: 4,943 Thanks: 3,096 Thanked 3,025 Times in 1,865 Posts Mentioned: 40 Post(s) Tagged: 2 Thread(s)	Maxed out the front (removed the locking rings), and maxed out the rear plus using some pre-load adjustment.

05-01-2017, 02:43 PM	#12
sIowbrz Member Join Date: Mar 2015 Drives: 2015 brz Location: markham Posts: 68 Thanks: 0 Thanked 11 Times in 7 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Something is wrong my flex z didnt even max out on 18x9.5 +38 is only .5 inch gap i can tuck the tires my rear is -2.3

05-01-2017, 07:47 PM	#14
mav1178 Senior Member Join Date: Apr 2013 Drives: 2005 Toyota Camry Location: 91745 Posts: 6,562 Thanks: 493 Thanked 6,093 Times in 3,029 Posts Mentioned: 95 Post(s) Tagged: 3 Thread(s)	Have you considered contacting Tein USA about this? If the shock body is bottoming out in the lower bracket, they made a design change in production that has obviously impacted the advertised specs. My Ohlins from 2013 were a similar situation, I suspect they used parts from another platform to reduce some manufacturing costs. -alex

User Name		Remember Me?
Password