|
||||||
| Software Tuning Discuss all software tuning topics. |
 |
|
|
Thread Tools | Search this Thread |
12-06-2017, 11:03 PM
|
#1 |
|
Member
Join Date: Mar 2017
Drives: 2014 BRZ
Location: Pittsburgh
Posts: 21
Thanks: 14
Thanked 14 Times in 5 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
AVCS logging on OFT question
I'm trying to experiment a bit with the AVCS system (at lower RPMs), intending to use it with the MAF Scaling Tool's VVT tool, and have run into a puzzle with my Open Flash Tablet: "vvt intake" seems to be super noisy, though "vvt int at" seems to be fine. In contrast, "vvt exhaust" seems to be fine.
Any suggestions? Should I just use "vvt int at" as the current intake angle and ignore whatever "vvt intake" is trying to present? https://datazap.me/u/baront/log-1512...4&zoom=510-731 |
|
|
|
12-07-2017, 05:31 AM
|
#2 |
|
Senior Member
Join Date: Jan 2013
Drives: Toyota 86
Location: South Korea
Posts: 267
Thanks: 127
Thanked 200 Times in 115 Posts
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
|
Did you compare it with VASC tables?
__________________
/* Custom underbody panels and diffuser
Custom electric water pump and PWM controller HKS GT EL header, 17MY intake manifold */ |
|
|
|
|
12-07-2017, 08:59 AM
|
#3 | |
|
Member
Join Date: Mar 2017
Drives: 2014 BRZ
Location: Pittsburgh
Posts: 21
Thanks: 14
Thanked 14 Times in 5 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Quote:
I'm mostly just curious about "vvt intake" because "vvt exhaust" seems to be fine. So is "vvt intake" just logging some junk value, or is my cam angle sensor messed up? |
|
|
|
|
|
12-07-2017, 04:03 PM
|
#4 |
|
Banned
Join Date: Dec 2013
Drives: FT86
Location: Australia
Posts: 7,998
Thanks: 1,035
Thanked 4,987 Times in 2,981 Posts
Mentioned: 598 Post(s)
Tagged: 2 Thread(s)
|
Looks like that vvt intake log parameter is logging rubbish
If your 2012-2016 you need to go to a bo1c or d rom to get correct logging in mamy cases |
|
|
|
|
09-03-2021, 08:18 AM
|
#5 |
|
Member
Join Date: Jul 2020
Drives: Subaru BRZ 2016
Location: Québec
Posts: 33
Thanks: 4
Thanked 11 Times in 9 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
I have the same Intake AVCS logging issue. @steve99, in your links it is stated that ZA1JA700C ,900C, A00C ,A01C , B00C are all compatible with ZA1JB01C. However I am using ZA1JF00C... do you think it is also compatible with B01C? I just want to check before I start porting all my maps to a ZA1JB01C rom.
|
|
|
|
|
09-03-2021, 10:58 PM
|
#6 | |
|
Banned
Join Date: Dec 2013
Drives: FT86
Location: Australia
Posts: 7,998
Thanks: 1,035
Thanked 4,987 Times in 2,981 Posts
Mentioned: 598 Post(s)
Tagged: 2 Thread(s)
|
Quote:
Yes any USA 2012-2016 manual car is compatible with ZA1JB01C firmware also make sure oft is updated and you manually update the Template File from oft support site |
|
|
|
|
| The Following User Says Thank You to steve99 For This Useful Post: | NicFromTheNorth (09-06-2021) |
|
09-10-2021, 04:50 PM
|
#7 |
|
Member
Join Date: Jul 2020
Drives: Subaru BRZ 2016
Location: Québec
Posts: 33
Thanks: 4
Thanked 11 Times in 9 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
One last question: to make a B01C rom appear as a F00C rom, can I just modify the bits corresponding to the ASCII representation of ZA1JB01C? Or is there more to be modified?
|
|
|
|
|
|
|
|
|
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| AVCS IDLE PATCHED | aagun | Software Tuning | 52 | 03-09-2023 01:32 PM |
| AVCS Explained | Rennmeister | Engine, Exhaust, Transmission | 3 | 03-15-2016 03:12 AM |
| AVCS tuning | Turdinator | Software Tuning | 9 | 11-24-2015 01:31 PM |
| Turbo AVCS/VVT settings | ztan | Forced Induction | 8 | 05-10-2015 04:17 AM |
| AVCS failures? | hmong337 | Forced Induction | 26 | 02-12-2015 03:01 PM |
