|
Software Tuning Discuss all software tuning topics. |
|
Thread Tools | Search this Thread |
04-30-2016, 05:00 PM | #1 |
Senior Member
Join Date: Feb 2016
Drives: 2013 Subaru BRZ Limited
Location: Silver City, NM
Posts: 258
Thanks: 12
Thanked 11 Times in 11 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
Omni 3bar map sensor values for ecutek
Wondering if anyone can provide the values I need to install the Omni 3bar sensor with an ecutek. I've been searching for days with no luck. Thanks for the help!
Sent from my D6708 using Tapatalk |
04-30-2016, 05:44 PM | #2 | |
Banned
Join Date: Dec 2013
Drives: FT86
Location: Australia
Posts: 7,998
Thanks: 1,035
Thanked 4,987 Times in 2,981 Posts
Mentioned: 598 Post(s)
Tagged: 2 Thread(s)
|
Quote:
Use at own risk :-) MAP Scalings for Alternative MAP sensors for Boosted cars (Manifold Pressure Sensors) Omni 2.5 Bar MAP The OFT300 (Vortex supercharger) map uses the 2.5 BAR Omni and has CEL-P0068 disabled in the map ok for 2.5 Bar OMNI MAP sensor ECUTEK scaling in BAR Manifold Pressure Sensor multiplier in bar per volt. = 0.500 Manifold pressure sensor offset. Value is measured in bar. = 0.100 MAP Sensor voltage max = 5.0v MAP sensor Voltage min = 0.0v Omni 3 Bar MAP Sensor (Metric in Bar) 0.617 - MULTIPLIER 0.03 - OFFSET scaling limits 0 - 4.75v Omni 4 Bar MAP Sensor Manifold Pressure Sensor Scaling - (imperial PSI) Multiplier - 12.087 Offset - 0.168 Metric/Bar bar/volt .833 offset (bar) .012 Manifold Pressure Sensor Limits - (CEL still comes on ) High Input CEL Above - 5.00v Low Input CEL Below - 0.00v Disable CEL P0103 and P0068 |
|
04-30-2016, 05:52 PM | #3 |
Senior Member
Join Date: Feb 2016
Drives: 2013 Subaru BRZ Limited
Location: Silver City, NM
Posts: 258
Thanks: 12
Thanked 11 Times in 11 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
Thank you!
Sent from my D6708 using Tapatalk |
05-30-2017, 04:23 PM | #4 | |
Member
Join Date: May 2016
Drives: 2016 FRS
Location: Michigan
Posts: 51
Thanks: 2
Thanked 28 Times in 14 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
Quote:
The offset for the Omni bar4 is supposed to be 31 |
|
05-30-2017, 06:25 PM | #5 |
Banned
Join Date: Dec 2013
Drives: FT86
Location: Australia
Posts: 7,998
Thanks: 1,035
Thanked 4,987 Times in 2,981 Posts
Mentioned: 598 Post(s)
Tagged: 2 Thread(s)
|
|
05-30-2017, 07:57 PM | #6 | |
Road-hole
Join Date: Jul 2014
Drives: 2013 Whiteout FR-S
Location: Gilbert, Arizona
Posts: 1,112
Thanks: 272
Thanked 479 Times in 292 Posts
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
|
I haven't had to disable the CEL...
Quote:
I've been running the omni 3bar and haven't had to disable any CELs so far. I've ran it for a couple of months. Jaden |
|
06-11-2017, 10:25 AM | #7 |
Member
Join Date: Aug 2014
Drives: 2013 Scion FR-S
Location: South Carolina
Posts: 66
Thanks: 7
Thanked 15 Times in 8 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
|
07-13-2017, 07:45 PM | #8 |
Member
Join Date: May 2016
Drives: 2016 FRS
Location: Michigan
Posts: 51
Thanks: 2
Thanked 28 Times in 14 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
|
07-13-2017, 07:47 PM | #9 |
Member
Join Date: May 2016
Drives: 2016 FRS
Location: Michigan
Posts: 51
Thanks: 2
Thanked 28 Times in 14 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
|
|
|
Thread Tools | Search this Thread |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
WTB: 3-Bar OMNI Map Sensor | FR-S Matt | Want-To-Buy Requests | 0 | 06-18-2014 12:14 PM |
Front Oxygen Sensor Scaling - How do we make it read richer values? | D-VO | Software Tuning | 7 | 05-08-2014 04:48 AM |
Omni 4 Bar Map Sensor New | Cross | Engine, Exhaust, Bolt-Ons | 3 | 04-06-2014 02:31 PM |
FS: NIB OMNI 4 BAR MAP Sensor | woode | Engine, Exhaust, Bolt-Ons | 3 | 04-04-2014 11:19 AM |
FS: NY - Omni 3 Bar Map Sensor | xxscaxx | Engine, Exhaust, Bolt-Ons | 7 | 03-11-2014 11:41 AM |