Wheel specs for Rocket Bunny Fenders

[megamarines]

Originally Posted by BCTV93

Why not just sell them for other reps with lower offsets?
I even thought about XXR 550s in +19 at one point.
Or be ghetto fab like what I'ma do and go real wheels in back, like 1,000$ with 0 offset or something and reps in front. And if all else fails, Varrstoen ES2 can be made in custom offset.
55mm Spacer just sounds scary for me :\ but if you could do it, it'd be a really good budget bunny build

Haha I debated it! And I'm eventually gonna grab some Works wheels, but not for a while. I really like my current setup, but was wondering how well it would transfer over with fender width extension. Also trying to stay functional, but really wondering how I can do that without jumping to 10.5+ all the way around.

[CyberAkuma]

Planning to go with Work Meister M1

18x9.5 -6 front
18x10.5 -31 rear

Any issues? Do I still need spacers? The red RB car from speedelement is running -40 in the rear so just wondering how this fitment would be compared to that one

[AznKirby]

Originally Posted by CyberAkuma

Planning to go with Work Meister M1

18x9.5 -6 front
18x10.5 -31 rear

Any issues? Do I still need spacers? The red RB car from speedelement is running -40 in the rear so just wondering how this fitment would be compared to that one

No spacers needed for sure. Depending on what size tires you run, and how low you're going, you may or may not rub

[CyberAkuma]

Originally Posted by AznKirby

No spacers needed for sure. Depending on what size tires you run, and how low you're going, you may or may not rub

Really appreciate the info Kirby, although it will not need spacers I would like to know will it poke? I'd also like some info on what tire sizes I can run for a slight stretch

[KIMOJIxSTYLE]

I'm running 18x11 and 18x13.5 lol and my offsets are double of speedelements, insta:x_mark_da_spot waiting for my v2 bodykit to arrive follow my build

[solus]

So...

will

18"
Front 9.5" Rear 10.5"
Offset Front -34 Rear -46

fit with V1 fenders, max -2 camber and 255/35/18 up front and 275s in the back?

[555]

Originally Posted by solus

So...

will

18"
Front 9.5" Rear 10.5"
Offset Front -34 Rear -46

fit with V1 fenders, max -2 camber and 255/35/18 up front and 275s in the back?

No

[solus]

Originally Posted by 555

No

Stick out, I'm guessing... seen it on a V2 and it stuck out a little

[BboyKidKoda]

Just get 18x10.5 -25 and 18x12 -40 meaty fitment


Sent from my iPhone using Tapatalk

[555]

19X10s. running 19x12 rear soon.

[wise345]

Originally Posted by BboyKidKoda

Just get 18x10.5 -25 and 18x12 -40 meaty fitment


Sent from my iPhone using Tapatalk

you have a picture of a v2 with these specs by chance?

[softgrip]

So, I don't have the car yet :\ But I've been looking at various wheels.

I basically want square 18x9.5s TE37SL. They look sick, and I believe it's plenty of grip.

What I would like to know is, is there some offset that is fine for naked BRZ, and then will still be OK later if I get a RB or Varis body kit?

I don't want to have to worry about selling/rebuying wheels. They are expensive!!

[kch]

Originally Posted by softgrip

So, I don't have the car yet :\ But I've been looking at various wheels.

I basically want square 18x9.5s TE37SL. They look sick, and I believe it's plenty of grip.

What I would like to know is, is there some offset that is fine for naked BRZ, and then will still be OK later if I get a RB or Varis body kit?

I don't want to have to worry about selling/rebuying wheels. They are expensive!!

Not without huge spacers. Seriously huge spacers.

[softgrip]

Originally Posted by kch

Not without huge spacers. Seriously huge spacers.

Is this a bad thing? How strong are these babies?