07-13-2018, 03:51 PM | #1 |
Senior Member
Join Date: Oct 2012
Drives: 1996 ST204, Series 10 FR-S
Location: Calgary, Alberta
Posts: 247
Thanks: 88
Thanked 200 Times in 85 Posts
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
|
3D Printed Midbass Mounting Rings, OEM speaker harness pigtail
Hi,
I had these set aside for a local guy but he ended up flaking on me. Ill see if anyone on here is interested in them. They are designed to mount standard 6.5" (165mm) speakers to the OEM bolt holes. These are solid ABS so they are very rigid. I will also include the yellow EC2 connectors to make the wiring clean. -Priced at 25USD plus shipping for the pair. -I also have a extra pair of the wiring pig tails if you do not want to cut the factory speaker wiring harness for $5USD plus shipping Attached are photos of a set I used in my car. Thanks! |
07-13-2018, 11:14 PM | #2 |
First 86 Driver Baby!
Join Date: Jan 2012
Drives: FR-S, Flex
Location: Williamsburg, VA
Posts: 1,751
Thanks: 502
Thanked 512 Times in 348 Posts
Mentioned: 32 Post(s)
Tagged: 3 Thread(s)
|
How far out do these put the speakers (from the door) and what is the cutout diameter? I have a set of Audiofrog GB60s (cutout diameter of 128mm) and would like to know if they would fit.
|
07-15-2018, 02:26 AM | #3 |
Senior Member
Join Date: Oct 2012
Drives: 1996 ST204, Series 10 FR-S
Location: Calgary, Alberta
Posts: 247
Thanks: 88
Thanked 200 Times in 85 Posts
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
|
@kmbkk
Wow, those are some darn nice drivers..... you are pretty serious about car audio. Sorry, I didn't see your post till now. 19mm total thickness from the door. I found that this is pretty much the furthest you can mount the drivers without trimming your door cards. I was able to put some ~3mm foam in front of the driver so the waves from the back of the driver cannot cancel out the front waves. 142mm cutout diameter. A little large for your driver but it should seal fine especially if you use foam or 3M tape on it. If these aren't up to your standards, shoot me a private message. Thanks! |
08-07-2018, 01:36 PM | #4 |
Senior Member
Join Date: Oct 2012
Drives: 1996 ST204, Series 10 FR-S
Location: Calgary, Alberta
Posts: 247
Thanks: 88
Thanked 200 Times in 85 Posts
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
|
sold, please close!
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Rear 3D Printed 6.5" Coax Speaker Adapters | TurboBRZ | Electronics | Audio | NAV | Infotainment | 34 | 07-20-2021 11:39 PM |
3D Printed Speaker Adapters | Shankenstein | Electronics | Audio | NAV | Infotainment | 57 | 09-21-2017 07:55 PM |
3D Printed 86 BRZ slimline number plate mounting bracket | rickjames | Cosmetic Modification (Interior/Exterior/Lighting) | 3 | 03-01-2015 07:14 PM |
Door Speaker Trim Rings Now Available | zetaproducts.net | Interior Parts (Incl. Lighting) | 35 | 08-27-2013 09:52 AM |
BRZ FOG LAMP Conversion Pigtail Harness Plug n Play | JPxM0Dz | Cosmetic Modification (Interior/Exterior/Lighting) | 4 | 03-31-2013 05:07 PM |