New to OFT, "file not compliant" - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

Wingnutt · 02-20-2022, 01:41 PM

So I finally got my OFT V2 tablet and went to try and get it setup.

It read the ECU fine and saved it, but afterward both the read and write buttons were greyed out.

I did a little searching and apparently that means that there are no maps on the tablet which are supported.

So I went to the openflash site, logged in and searched for maps.

I searched my calibration ID, which is is ZA1JB01C

I found a set of tunes matching this:
OTS Maps for ZA1JB01C (MY2014 US 6MT); v4.03

Downloaded the stage 2 plus map, launched openflash manager, selected upload, selected the .bin file and i get "The file selected is not compliant"

Thats where I'm at, I searched the forum for that error code and found two threads but both were quite dated and the info wasn't very relevant .

Did I miss something? am I doing something wrong?

2014 FRS MT
ECU TYPE: DENS0 GT86
Cal: ZA1JB01C

Wingnutt · 02-20-2022, 02:13 PM

I think what is going on is my car had a previous tune.

It came with an aftermarket catless header and I noticed it didn't throw any CEL, so it must have some sort of tune on it already which explains why the tablet wont generate any.

I looked this up and found the following reference:

The fix is to download the full format .bin tunes from openflash site unzip the downloaded files, DELETE the database format tunes in OFT using OFM, then load up the required full format tune .bin tune files to match your CALID of your stock ROM.

I have tried searching quit a bit but cannot locate any such "full format " file for my car on the openflash site.

02-20-2022, 01:41 PM	#1
Wingnutt Member Join Date: Apr 2021 Drives: Pearl White 2014 Location: Texas Posts: 77 Thanks: 1 Thanked 46 Times in 17 Posts Mentioned: 2 Post(s) Tagged: 0 Thread(s)	New to OFT, "file not compliant" So I finally got my OFT V2 tablet and went to try and get it setup. It read the ECU fine and saved it, but afterward both the read and write buttons were greyed out. I did a little searching and apparently that means that there are no maps on the tablet which are supported. So I went to the openflash site, logged in and searched for maps. I searched my calibration ID, which is is ZA1JB01C I found a set of tunes matching this: *OTS Maps for ZA1JB01C (MY2014 US 6MT); v4.03* Downloaded the stage 2 plus map, launched openflash manager, selected upload, selected the .bin file and i get "The file selected is not compliant" Thats where I'm at, I searched the forum for that error code and found two threads but both were quite dated and the info wasn't very relevant . Did I miss something? am I doing something wrong? 2014 FRS MT ECU TYPE: DENS0 GT86 Cal: ZA1JB01C

02-20-2022, 02:13 PM	#2
Wingnutt Member Join Date: Apr 2021 Drives: Pearl White 2014 Location: Texas Posts: 77 Thanks: 1 Thanked 46 Times in 17 Posts Mentioned: 2 Post(s) Tagged: 0 Thread(s)	I think what is going on is my car had a previous tune. It came with an aftermarket catless header and I noticed it didn't throw any CEL, so it must have some sort of tune on it already which explains why the tablet wont generate any. I looked this up and found the following reference: The fix is to download the full format .bin tunes from openflash site unzip the downloaded files, DELETE the database format tunes in OFT using OFM, then load up the required full format tune .bin tune files to match your CALID of your stock ROM. I have tried searching quit a bit but cannot locate any such "full format " file for my car on the openflash site.

User Name		Remember Me?
Password