What did you do to your 2nd gen BRZ today? - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

dragoontwo · 11-22-2021, 10:19 PM

Let's get this second gen thread going.

I installed my STI start button from my 20. I also installed my flexible v-bars. While I had the dsh apart I went ahead and removed the engine speaker that was right there.

I also found a quick and easy way to unplug the active sound control(engine noise speaker computer). Open the passenger door, remove the side panel and the plug for the unit is right there. I was able to get a couple of fingers in there and dialed the plug. See the attached photos.

FritoPendejo · 11-22-2021, 10:41 PM

How thoughtful of them to have made it so easy.

Got wheels swapped back to OEM on the FRS so I can swap my Motegis onto the BRZ when it finally arrives, got tradein value for it as well. They offered me more than carvana did so I'm happy with that.

Frost · 11-23-2021, 10:14 AM

So just unplug that lower plug on the bottom of the silver box?

dragoontwo · 11-23-2021, 10:34 AM

Quote:

Originally Posted by Frost

So just unplug that lower plug on the bottom of the silver box?

Yep.

Yoshoobaroo · 11-23-2021, 11:46 AM

Quote:

Originally Posted by dragoontwo

-my STI start button from my 20-

Do you have the part number for that switch? It looks different from the others I’ve seen. How was the install?

Quote:

I also found a quick and easy way to unplug the active sound control(engine noise speaker computer). Open the passenger door, remove the side panel and the plug for the unit is right there.

No errors/shadow codes after unplugging?

dragoontwo · 11-23-2021, 12:02 PM

Quote:

Originally Posted by Yoshoobaroo

Do you have the part number for that switch? It looks different from the others I’ve seen. How was the install?

83031CA024 $85.48 at Subaru Source. From 2018 BRZ STI.

Lots of dash removal to get to the little bugger. The HVAC control panel needs to come off, so the radio panel also needs to be slid out far enough to get it off.

Quote:

No errors/shadow codes after unplugging?

Not sure yet. I haven't scanned it to see if any codes were pending. Can do later tonight.

dragoontwo · 11-23-2021, 07:09 PM

No codes readable from my end having the ASC disconnected. Not sure what the dealer may see, but also don't care.

Re: STI push button. I'm a dumbass. It's even easier than the last model to replace. Just grab the trim around the button and pull it straight out. It can be a bit fussy lining it up to reinstall though. Should take less than a minute to change.

Yoshoobaroo · 11-23-2021, 08:16 PM

Got her home!

MikeNSX2 · 11-23-2021, 10:41 PM

Ordered a stainless steel WC Lathewerks shift knob.

Chris makes outstanding shift knobs, and I have one in my Focus ST and had one in my just sold Miata ND.

SpectreRT · 11-23-2021, 10:48 PM

Quote:

Originally Posted by Yoshoobaroo

Got her home!

Super happy for you, and 10000% jealous. The red looks amazing.

Yoshoobaroo · 11-23-2021, 11:42 PM

I tried my tomei Duracon type SS shift knob and it didn’t fit. It screwed on just fine until it had to fit over the reverse lockout, looks like that diameter is a bit bigger now.

Edit: the new shift knob has a 27.75mm diameter bore for the reverse lockout. The old shift knobs were only ~24mm. For everyone considering custom made knobs, make sure your machinist knows this dimension is different from the 1st gen cars.

fredzy · 11-24-2021, 11:26 AM

Quote:

Originally Posted by dragoontwo

No codes readable from my end having the ASC disconnected. Not sure what the dealer may see, but also don't care.

Re: STI push button. I'm a dumbass. It's even easier than the last model to replace. Just grab the trim around the button and pull it straight out. It can be a bit fussy lining it up to reinstall though. Should take less than a minute to change.

Regarding the sound generator disconnect, do you think you could take some in-car video revving it out with generator deactivated? I'm really curious to hear the car without it.

The car seems to make a not-so-nice buzzy sound that I think/hope is all coming from the generator. Reviewer comments seem to be neutral to negative about it. I guess the thing will be EV quiet without it, but that's where aftermarket can begin.

Big thanks for being probably the first person to get to the bottom of this one!

Yoshoobaroo · 11-24-2021, 11:37 AM

1st milestone

Frost · 11-24-2021, 01:19 PM

Quote:

Originally Posted by Yoshoobaroo

1st milestone

Niiiiice.

11-22-2021, 10:19 PM	#1
dragoontwo Senior Member Join Date: May 2020 Drives: 22 BRZ limited Location: Clarksville TN Posts: 1,198 Thanks: 219 Thanked 1,006 Times in 530 Posts Mentioned: 7 Post(s) Tagged: 0 Thread(s)	What did you do to your 2nd gen BRZ today? Let's get this second gen thread going. I installed my STI start button from my 20. I also installed my flexible v-bars. While I had the dsh apart I went ahead and removed the engine speaker that was right there. I also found a quick and easy way to unplug the active sound control(engine noise speaker computer). Open the passenger door, remove the side panel and the plug for the unit is right there. I was able to get a couple of fingers in there and dialed the plug. See the attached photos. Attached Images Last edited by dragoontwo; 12-06-2021 at 08:39 PM. Reason: Title change.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
WHAT DID YOU DO TO YOUR FRS TODAY?	KalbiCool88	Scion FR-S / Toyota 86 GT86 General Forum	1	11-04-2015 11:36 PM
Do you know what today is?	Yruyur	Off-Topic Lounge [WARNING: NO POLITICS]	26	01-21-2015 03:51 PM
just got my OFT today...help please!	carlitosway6891	Software Tuning	9	02-20-2014 11:05 PM
TODAY, TODAY, I GET IT TODAY!!!! :D	Trashed675	Scion FR-S / Toyota 86 GT86 General Forum	54	02-14-2013 02:16 AM
sat in a BRZ today	NESW20	BRZ First-Gen (2012+) -- General Topics	8	03-31-2012 09:53 AM

11-22-2021, 10:41 PM	#2
FritoPendejo Member Join Date: Oct 2020 Drives: FRS Location: Arkansas Posts: 23 Thanks: 2 Thanked 11 Times in 6 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	How thoughtful of them to have made it so easy. Got wheels swapped back to OEM on the FRS so I can swap my Motegis onto the BRZ when it finally arrives, got tradein value for it as well. They offered me more than carvana did so I'm happy with that.

11-23-2021, 07:09 PM	#7
dragoontwo Senior Member Join Date: May 2020 Drives: 22 BRZ limited Location: Clarksville TN Posts: 1,198 Thanks: 219 Thanked 1,006 Times in 530 Posts Mentioned: 7 Post(s) Tagged: 0 Thread(s)	No codes readable from my end having the ASC disconnected. Not sure what the dealer may see, but also don't care. Re: STI push button. I'm a dumbass. It's even easier than the last model to replace. Just grab the trim around the button and pull it straight out. It can be a bit fussy lining it up to reinstall though. Should take less than a minute to change.

11-23-2021, 10:41 PM	#9
MikeNSX2 Senior Member Join Date: Oct 2021 Drives: Ice Silver 2022 BRZ Limited Location: Tennessee Posts: 134 Thanks: 58 Thanked 86 Times in 44 Posts Mentioned: 3 Post(s) Tagged: 0 Thread(s)	Ordered a stainless steel WC Lathewerks shift knob. Chris makes outstanding shift knobs, and I have one in my Focus ST and had one in my just sold Miata ND.

User Name		Remember Me?
Password