|
Software Tuning Discuss all software tuning topics. |
|
Thread Tools | Search this Thread |
08-28-2020, 02:08 AM | #1 |
Junior Member
Join Date: Jul 2020
Drives: 2014 Scion FRS
Location: Ca
Posts: 3
Thanks: 0
Thanked 1 Time in 1 Post
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Need Help OFT ERROR CODE
Hey so I already had a tune installed for a while but was trying to change tunes. During installing the new tune it erased my ecu file like normal but then failed , So now I I have no ecu tune at all and can’t start my car. I’ve tried installing the same tune I was on and each time I do I get an error code 10010. I can’t even go back to the original file. I’ve been trying for the past 3 hours. And I’m in a parking garage where my car can get towed so I can’t leave my car.
This is the error An error accused while writing the ECU. Check Cable connections, ignition switch positions, then try again later. OFTCODE: 10010 I’ve tried disconnecting the battery Installing new tune files Making sure all windows are up and doors closed Checked cable connections |
The Following User Says Thank You to BayArea_FRS For This Useful Post: | Lav (09-13-2022) |
08-28-2020, 07:03 AM | #2 | |
Banned
Join Date: Dec 2013
Drives: FT86
Location: Australia
Posts: 7,998
Thanks: 1,035
Thanked 4,987 Times in 2,981 Posts
Mentioned: 598 Post(s)
Tagged: 2 Thread(s)
|
Quote:
make sure barry volts above avout 12 v also try writing the stock ie original tune file to car |
|
08-28-2020, 08:36 AM | #3 | |
Senior Member
Join Date: May 2017
Drives: Hot lava FRS Monogram Charizard
Location: Sacramento Ca
Posts: 329
Thanks: 22
Thanked 85 Times in 63 Posts
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Sent from my GM1915 using Tapatalk |
|
08-30-2020, 06:53 PM | #4 |
Junior Member
Join Date: Jul 2020
Drives: 2014 Scion FRS
Location: Ca
Posts: 3
Thanks: 0
Thanked 1 Time in 1 Post
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
The battery comes on
|
08-30-2020, 07:38 PM | #5 |
Member
Join Date: Sep 2019
Drives: Scion FRS 10 series
Location: Santa Rosa CA
Posts: 39
Thanks: 6
Thanked 25 Times in 17 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
When you turn your car to the "on" position , 2 clicks on push to start/key position 2, do you hear the fuel pump energize? Also do you have the latest updates on the open flash tablet? You might have bricked your ecu if you powered off the car after the failed flash instead of trying to reflash the car again after failure.
|
09-13-2022, 01:11 AM | #6 | |
Senior Member
Join Date: Jan 2019
Drives: Frs
Location: CA
Posts: 118
Thanks: 173
Thanked 23 Times in 20 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
Quote:
DId you ever figure this out? Its kind of frustrating that after all the work Open Flash did on making these tunes + making them flashable by the end user, they went with the cheapest shittiest tablets possible. I'd have gladly paid an extra 100$ to not have to pray to god every time I switch off E85 |
|
09-13-2022, 02:35 AM | #7 |
Junior Member
Join Date: Apr 2017
Drives: Toyota GT86 MY2017
Location: Italy
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
I've got the same issue and i fixed it by program back the ECU using Tactrix.
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Error Code B2779 | Chris14a | Issues | Warranty | Recalls / TSB | 2 | 10-14-2018 03:58 PM |
B1692 ERROR CODE | NIKDENG | Engine, Exhaust, Transmission | 3 | 08-05-2016 11:37 PM |
Help Error code C1241 | acro | Issues | Warranty | Recalls / TSB | 3 | 04-18-2016 11:51 PM |
Error code B14A1... wth is it? | SirBrass | Software Tuning | 4 | 04-24-2014 05:37 PM |
Unichip Error Code | Ingeberger | Engine, Exhaust, Transmission | 5 | 12-29-2013 01:09 PM |