|
Tracking / Autocross / HPDE / Drifting What these cars were built for! |
|
Thread Tools | Search this Thread |
08-29-2024, 12:57 AM | #43 |
Senior Member
Join Date: May 2011
Drives: '23 BRZ
Location: Providence, RI
Posts: 4,634
Thanks: 1,418
Thanked 3,964 Times in 2,071 Posts
Mentioned: 85 Post(s)
Tagged: 0 Thread(s)
|
FWIW the few times I've installed coilovers, measuring to ensure same left/right free lengths (i.e. same amount of thread showing) while setting ride height, I've wound up within 1% of 50/50 corner-weights right off the bat.
If they have scales at the track perhaps you could check corner weights there and adjust if necessary. |
The Following 3 Users Say Thank You to ZDan For This Useful Post: |
08-29-2024, 09:28 AM | #44 | |
Member
Join Date: May 2023
Drives:
Posts: 79
Thanks: 19
Thanked 21 Times in 17 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Yep. The 949 article mentions that too. But for sanity check and just to get #s too, I’ll just do both alignment and corner balance. Now I’m working on trying to figure out my dampening settings. Which has been tough, before i even go race. On the street been following this process: ———————————————————————————— So I started with everything at the softest position. Start by driving around, feel out the car a little bit. Then come back to your garage/driveway to do a change. 1. Start by increasing front compression 2 clicks at a time, then go drive after each time you increase the damping. When the front start feeling harsh over bumps (skipping through bumps or jolting the chassis upward - trust me you will feel this), decrease it by 1 or 2 clicks. 2. Rear compression next, follow the same procedure. 3. Front rebound 3rd, increase this 1 click at a time until you feel like the front is oscillating in between 1 or 2 cycles. Then back off 1 click. 4. Lastly rear rebound. Follow the front rebound procedure but back off one additional click than front rebound (this is usually a rotation like rebound setting) This usually come out to be running most amount of compression damping and least amount of rebound. When you're on track/auto cross, drive the first session with your street set damping profile. If the car feels really wallowy and lazy, increase all 4 corners' compression by a few clicks (let's say 3 clicks). Then drive the next session with the increase. ———————————————————————————— So I tried working on compression today, I ended up with -4 from full stiff (12 clicks total) for front and rear with 7/9k springs. I must say I did find it hard to feel when the compression was too much, especially in the rear. It was notable the car would get more bouncy and even a little more sensitive over bumps. But it wasn’t as clear as I hoped to find that point where it got too harsh or skipping bumps. I think it’s close to where it should be though, just shocked to see it’s almost full stiff on front and rear for compression. Tomorrow I’ll try rebound and see if that’s easier to feel out. Sent from my iPhone using Tapatalk |
|
The Following User Says Thank You to Tomyyyu For This Useful Post: | ZDan (09-05-2024) |
08-29-2024, 10:12 AM | #45 | |
Member
Join Date: May 2023
Drives:
Posts: 79
Thanks: 19
Thanked 21 Times in 17 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
GR86 - Understeer Alleviation - RCE Tarmac 2 (7k square setup)
Quote:
Interesting. I’m on 7/9k so close to yours, mine is 400/500. I did end up also increasing my ride height as I definitely was bottoming out the front on bumps. First thing I noticed on the street was much less rear weight shifting upon acceleration, that the rear seems to follow the front a lot closer, I actually get feeling from what’s happening in the rear, and the ride isn’t “crashing” anymore. Instead it’s stiff, but doesn’t crash. Will have to see how the 7/9k holds up in autocross. For compression, from my own street test and tune and capabilities I ended up about the same, 4 clicks from full stiff for compression on all four corners. I’ll be playing with rebound next using my steps (one of the posts on this thread). Sent from my iPhone using Tapatalk Last edited by Tomyyyu; 09-03-2024 at 09:53 PM. |
|
08-29-2024, 05:21 PM | #46 |
Senior Member
Join Date: Apr 2016
Drives: 23 BRZ 15 Impreza
Location: NY
Posts: 163
Thanks: 64
Thanked 78 Times in 52 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Is that Devens? The talent pool out there is deep... Have someone take a run or two in your car, see if Evan is still out there. Drives a dark blue frs, crazy fast!
|
The Following User Says Thank You to cueball89 For This Useful Post: | Tomyyyu (08-29-2024) |
09-03-2024, 07:23 PM | #47 |
The Dictater
Join Date: Apr 2017
Drives: '13 Red Scion FRS
Location: MD, USA
Posts: 9,544
Thanks: 26,450
Thanked 12,574 Times in 6,229 Posts
Mentioned: 87 Post(s)
Tagged: 0 Thread(s)
|
Hope OP doesn't mind me piggy backing on this. I have the exact same issue with my '13 FRS and this has been helpful. Also another data point for the interested.
My current stx setup T2s + camber plates, 7k f/r, Perrin 19mm front on stiff, stock (15mm?) rear, re71rs Value: front/Rear Hot pressures: 32/30 Caster: 7.5/- Camber: 3.6(FL-limited)/2.3 Toe: 0/0 Bump: 11/7 from stiff Rebound: 9/13 from stiff Ride height: 335/340 wheel center to top of well So in terms of things I have the time to try before the season ends, I can play with damper settings, ride height, and possibly sway bars. I could try eccentric bolts for more front camber but I would prefer not to use those. Thinking of upping rake to about 10mm from 5mm. Possibly also getting a 16mm rear sway bar and working on damping from there?
__________________
If a picture is worth a thousand words, a model is worth ten thousand pictures.
Also: "Build Thread" Last edited by Spuds; 09-05-2024 at 02:47 AM. Reason: Corrected ride height measurements |
09-03-2024, 09:51 PM | #48 | |
Member
Join Date: May 2023
Drives:
Posts: 79
Thanks: 19
Thanked 21 Times in 17 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
GR86 - Understeer Alleviation - RCE Tarmac 2 (7k square setup)
Quote:
What does FL Limited mean? But yeah, this is pretty easy off the bat. 7k square doesn’t work. Especially with the bar you have. You could either try the OEM front bar or try 9k rear springs due to the motion ratio of 0.95 front and 0.78 rear for the second generation (which is similar in the 1st gen). The more rake you have the less rear grip, and vice versa. We would need your pinch weld heights to give you a better reference. Sent from my iPhone using Tapatalk |
|
The Following User Says Thank You to Tomyyyu For This Useful Post: | Spuds (09-03-2024) |
09-03-2024, 10:37 PM | #49 | |
The Dictater
Join Date: Apr 2017
Drives: '13 Red Scion FRS
Location: MD, USA
Posts: 9,544
Thanks: 26,450
Thanked 12,574 Times in 6,229 Posts
Mentioned: 87 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Floor to pinch welds jack points is ~130/136mm. I'm not sure allowing more overall roll is the answer though because that's how you lose camber?
__________________
If a picture is worth a thousand words, a model is worth ten thousand pictures.
Also: "Build Thread" |
|
09-05-2024, 02:05 AM | #50 | |
Senior Member
Join Date: May 2020
Drives: 2017 BRZ series.yellow
Location: Idaho
Posts: 249
Thanks: 127
Thanked 187 Times in 107 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Quote:
In any case. Too me it looks like you need more front camber, then a bit more rake and either more rear bar, or less front bar. Not talking swapping to oem FSB, but perhaps moving to the soft setting. I think that ideally you'd stiffing up the rear some instead of softening the front. But without changing hardware, your only option is rear dampening settings and/or front sway bar setting. What camber plates are you running? I'm surprised you can't get more. I'm on T2's and Vorshlag plates. No special hardware in the strut to knuckle connection, just pushed in as much as the slots will allow then camber plates at max. Sitting at -4.3 camber. |
|
The Following User Says Thank You to Breezio For This Useful Post: | Spuds (09-05-2024) |
09-05-2024, 02:44 AM | #51 | |
The Dictater
Join Date: Apr 2017
Drives: '13 Red Scion FRS
Location: MD, USA
Posts: 9,544
Thanks: 26,450
Thanked 12,574 Times in 6,229 Posts
Mentioned: 87 Post(s)
Tagged: 0 Thread(s)
|
Quote:
I think I'll get at 16mm rear bar, those are somewhat easy to swap out. Was looking at rake earlier today. If I could swing some more drop up front that would help with both rake and camber...
__________________
If a picture is worth a thousand words, a model is worth ten thousand pictures.
Also: "Build Thread" |
|
09-05-2024, 09:40 AM | #52 | |
Member
Join Date: May 2023
Drives:
Posts: 79
Thanks: 19
Thanked 21 Times in 17 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Quote:
I would avoid the rear bar. 949 is pretty adamant on that and he’s a knowledgeable poster. https://www.949racing.com/supermiata...lignment-info/ Sent from my iPhone using Tapatalk |
|
The Following User Says Thank You to Tomyyyu For This Useful Post: | Spuds (09-05-2024) |
09-05-2024, 10:08 AM | #53 |
Senior Member
Join Date: May 2011
Drives: '23 BRZ
Location: Providence, RI
Posts: 4,634
Thanks: 1,418
Thanked 3,964 Times in 2,071 Posts
Mentioned: 85 Post(s)
Tagged: 0 Thread(s)
|
If you've been bottoming out the front, IMO that is most of your understeer problem. I'm guessing the Tarmac 2s might have less front bump travel than RCE SS-2 I'm running. I'm at 330F/335R ride heights. Was amazed at how much less mid-corner understeer vs. my old '17, which had less front bump travel...
Last edited by ZDan; 09-05-2024 at 10:37 AM. |
The Following 2 Users Say Thank You to ZDan For This Useful Post: | Spuds (09-05-2024) |
09-05-2024, 10:20 AM | #54 | |
Senior Member
Join Date: May 2020
Drives: 2017 BRZ series.yellow
Location: Idaho
Posts: 249
Thanks: 127
Thanked 187 Times in 107 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Quote:
|
|
The Following User Says Thank You to Breezio For This Useful Post: | Spuds (09-05-2024) |
09-05-2024, 10:33 AM | #55 |
The Dictater
Join Date: Apr 2017
Drives: '13 Red Scion FRS
Location: MD, USA
Posts: 9,544
Thanks: 26,450
Thanked 12,574 Times in 6,229 Posts
Mentioned: 87 Post(s)
Tagged: 0 Thread(s)
|
Yeah, the plates are pushed all the way inboard, even started looking around for warping/damage but couldn't find any reason outside of manufacturing tolerances.
__________________
If a picture is worth a thousand words, a model is worth ten thousand pictures.
Also: "Build Thread" |
09-05-2024, 10:46 AM | #56 | |
The Dictater
Join Date: Apr 2017
Drives: '13 Red Scion FRS
Location: MD, USA
Posts: 9,544
Thanks: 26,450
Thanked 12,574 Times in 6,229 Posts
Mentioned: 87 Post(s)
Tagged: 0 Thread(s)
|
Quote:
It also says to stay above 140mm ride height... Maybe I went lower than I thought I did...
__________________
If a picture is worth a thousand words, a model is worth ten thousand pictures.
Also: "Build Thread" |
|
|
|
Thread Tools | Search this Thread |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Understeer on '22 BRZ | Fletch | Tracking / Autocross / HPDE / Drifting | 29 | 12-20-2022 10:09 PM |
oversteer and understeer | orc | BRZ Second-Gen (2022+) -- General Topics | 76 | 10-05-2021 04:08 PM |
Why does car understeer when going downhill? | hpde_addict | Tracking / Autocross / HPDE / Drifting | 20 | 01-15-2018 10:42 AM |
Understeer after new wheels | carsebuco | Wheels | Tires | Spacers | Hub -- Sponsored by The Tire Rack | 16 | 12-04-2017 06:49 PM |
understeer on 17 brz | alex.s | Suspension | Chassis | Brakes -- Sponsored by 949 Racing | 37 | 09-11-2017 05:05 AM |