2013 frs Turbo/built motor/flexfuel - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

Kurd · 01-14-2021, 04:03 PM

Hello,

Thinking about parting ways with my FRS that I've owned for 6 years. Car is in excellent condition and meticulously kept inside and out. Only reason I am considering selling it is because I have picked up another project car and this car stays in the garage. I have driven the car 1k miles in the last year and a half.

2013 frs 52k miles/2nd owner/no accidents

Engine & Transmission:
Sbd500x Cerakoted hot parts in Tungsten color- installed @ 47k miles ~ 5k miles since install
Motor built at 45k miles
Cp pistons 10:1
Skunk2 Pro Connecting Rods
ARP Head Studs
King XP Performance Rod Bearing Set
GSC Beehive Performance Valve Springs
upgraded fuel pump/injectors
Zeitronix Flex fuel kit
Bluemoon baffle plate
KillerBee pick up tube
DSS carbon driveshaft
Perrin over pipe
Tanabe front pipe
Borla type s catback
Spec upgraded clutch
MAPerformance 19 row setrab cooler
mounted behind pass. fog cutout
Carbon fiber Catch can
futomoto drain valve
Dei and fire protective sleeve on coolant/oil lines

Exterior:
18x8.5 18x9.5 rota mx-r wheels wrapped in Pilot Super Sport 255/40 square
Front/side and rear lip
tinted rear taillight
smoked lower third light

Interior:
Custom carbon fiber and alcantara steering wheel
P3 vent gauge
Flexfuel gauge
manual boost gauge
In dash headunit with bluetooth/phone capability
Flossy weighted shift knob

Suspension:
Fortune auto 500 coilovers
SPC Lower rear control arms
performance alignment from agile performance in MD

I am probably forgetting a bunch of stuff, feel free to message me with any questions.

The car needs nothing. I repeat the car needs absolutely nothing. It is mint inside and out. Zero issues. No rubbing, creaking, clicking etc.

Motor was built and tuned on ecutek by Brady @ pure automotive perf. in Millersville, MD
Car made 300 whp on pump gas and 405 whp / 335wtq on full ethanol.
I usually run the car on a mixture which should be around 325-350 whp and it's plenty fast.

Asking price is $22k. NEW PRICE: $20k FIRM!!

Please keep your opinions to yourself if you do not like the price. I do not care. I will hold on to the car if I have to.. it is paid off!

If anyone is genuinely interested, please message me at 301-312-7535 as I do not visit this site very often.

Location: Laurel, MD

TheGimster · 01-14-2021, 11:30 PM

Not that bad of a price IMO given the low miles and forged internals - GLWS!

p1l0t · 01-19-2021, 11:01 PM

Why would you sell that? :confused:

Sent from my SM-G975U using Tapatalk

jflogerzi · 01-24-2021, 11:12 AM

GLWS. Super clean car.

Sent from my GM1915 using Tapatalk

Kurd · 02-01-2021, 12:17 PM

Thank you guys for the kind words.

I was recently offered $20k from an out of state person for the car which I eventually accepted but then the dude went no contact without even seeing the vehicle.
So, I figured I'd update the post with the new sale price I am willing to let the car go for.

The vehicle is currently only listed on ft86. I will eventually post it elsewhere for more exposure. Thank you.

Kurd · 02-22-2021, 10:48 PM

Sale Pending

Kurd · 03-03-2021, 05:29 PM

SOLD!

Mods please remove. Thank you for letting me post.

01-14-2021, 04:03 PM	#1
Kurd Member Join Date: Nov 2018 Drives: 2013 FR-S Location: Savage, MD Posts: 17 Thanks: 3 Thanked 1 Time in 1 Post Mentioned: 0 Post(s) Tagged: 0 Thread(s)	2013 frs Turbo/built motor/flexfuel Hello, Thinking about parting ways with my FRS that I've owned for 6 years. Car is in excellent condition and meticulously kept inside and out. Only reason I am considering selling it is because I have picked up another project car and this car stays in the garage. I have driven the car 1k miles in the last year and a half. 2013 frs 52k miles/2nd owner/no accidents Engine & Transmission: Sbd500x Cerakoted hot parts in Tungsten color- installed @ 47k miles ~ 5k miles since install Motor built at 45k miles Cp pistons 10:1 Skunk2 Pro Connecting Rods ARP Head Studs King XP Performance Rod Bearing Set GSC Beehive Performance Valve Springs upgraded fuel pump/injectors Zeitronix Flex fuel kit Bluemoon baffle plate KillerBee pick up tube DSS carbon driveshaft Perrin over pipe Tanabe front pipe Borla type s catback Spec upgraded clutch MAPerformance 19 row setrab cooler mounted behind pass. fog cutout Carbon fiber Catch can futomoto drain valve Dei and fire protective sleeve on coolant/oil lines Exterior: 18x8.5 18x9.5 rota mx-r wheels wrapped in Pilot Super Sport 255/40 square Front/side and rear lip tinted rear taillight smoked lower third light Interior: Custom carbon fiber and alcantara steering wheel P3 vent gauge Flexfuel gauge manual boost gauge In dash headunit with bluetooth/phone capability Flossy weighted shift knob Suspension: Fortune auto 500 coilovers SPC Lower rear control arms performance alignment from agile performance in MD I am probably forgetting a bunch of stuff, feel free to message me with any questions. The car needs nothing. I repeat the car needs absolutely nothing. It is mint inside and out. Zero issues. No rubbing, creaking, clicking etc. Motor was built and tuned on ecutek by Brady @ pure automotive perf. in Millersville, MD Car made 300 whp on pump gas and 405 whp / 335wtq on full ethanol. I usually run the car on a mixture which should be around 325-350 whp and it's plenty fast. Asking price is $22k. NEW PRICE: $20k FIRM!! Please keep your opinions to yourself if you do not like the price. I do not care. I will hold on to the car if I have to.. it is paid off! If anyone is genuinely interested, please message me at 301-312-7535 as I do not visit this site very often. Location: Laurel, MD Attached Images Last edited by Kurd; 02-01-2021 at 12:21 PM.

02-22-2021, 10:48 PM	#6
Kurd Member Join Date: Nov 2018 Drives: 2013 FR-S Location: Savage, MD Posts: 17 Thanks: 3 Thanked 1 Time in 1 Post Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Sale pending Sale Pending

03-03-2021, 05:29 PM	#7
Kurd Member Join Date: Nov 2018 Drives: 2013 FR-S Location: Savage, MD Posts: 17 Thanks: 3 Thanked 1 Time in 1 Post Mentioned: 0 Post(s) Tagged: 0 Thread(s)	SOLD! SOLD! Mods please remove. Thank you for letting me post.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
FS-2013 Built Motor High HP Turbo Setup-Finishing up at the shop	FT86RGV	Cars for Sale/Trade	10	03-24-2017 05:53 PM
JDL's Shop Fr-s build Built motor V-mount Turbo	JDLAutoDesign	Member's Car Journals	12	10-11-2016 11:54 AM
IN: 05 GTO (built motor and rearmount turbo)	Subi-Subi-Ruu	Cars for Sale/Trade	4	12-14-2014 08:59 PM
Crawford Limited Turbo BRZ - built motor	Mrqb22	Forced Induction	8	11-11-2013 01:34 PM

01-14-2021, 11:30 PM	#2
TheGimster Member Join Date: Jun 2019 Drives: 11 STI 650whp(sold); 19 WRX 402whp Location: Alabama Posts: 19 Thanks: 0 Thanked 8 Times in 7 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Not that bad of a price IMO given the low miles and forged internals - GLWS!

01-19-2021, 11:01 PM	#3
p1l0t Senior Member Join Date: Jan 2016 Drives: 2016 Subaru BRZ Hyperblue Location: West Hartford, CT Posts: 8,416 Thanks: 22,575 Thanked 9,371 Times in 4,813 Posts Mentioned: 58 Post(s) Tagged: 1 Thread(s)	Why would you sell that? :confused: Sent from my SM-G975U using Tapatalk

02-01-2021, 12:17 PM	#5
Kurd Member Join Date: Nov 2018 Drives: 2013 FR-S Location: Savage, MD Posts: 17 Thanks: 3 Thanked 1 Time in 1 Post Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Thank you guys for the kind words. I was recently offered $20k from an out of state person for the car which I eventually accepted but then the dude went no contact without even seeing the vehicle. So, I figured I'd update the post with the new sale price I am willing to let the car go for. The vehicle is currently only listed on ft86. I will eventually post it elsewhere for more exposure. Thank you.

User Name		Remember Me?
Password