ECUFlash - Getting close!

[steve99]

Originally Posted by Td-d

Someone want to do some tests for me? Trying to check an address for Fueling Mode (PI, DI, Both).

for A01C, can you log 0xFFF8BD33 as an 8bit, and see if it correlates to what would likely be fueling mode (1,2, or 3).

I would but I'm on G rom.

[regal]

Originally Posted by Td-d

Someone want to do some tests for me? Trying to check an address for Fueling Mode (PI, DI, Both).

for A01C, can you log 0xFFF8BD33 as an 8bit, and see if it correlates to what would likely be fueling mode (1,2, or 3).

I won't have time to figure out logging for about a month. I will say going from A00C to B01C is a huge upgrade, if you believe the torque app much less knock. The engine just feels healthier and doesn't stumble and ping at all. Cold starts and idling in general are a huge improvement.

[Td-d]

Originally Posted by steve99

I would but I'm on G rom.

Then you can try FFF8BC2F

[steve99]

Originally Posted by Td-d

Then you can try FFF8BC2F

put this in logcfg.txt

;DI PI Both 1 2 3
paramname = Fuel_mode
paramid = 0xFFF8BC2F
databits = 8
scalingrpn = x


always logged "0" unfortunatly.

[Td-d]

Whilst driving, or in idle?

[Td-d]

Also - can you try unk_FFF8F5A0 for me?

[vgi]

Originally Posted by Td-d

Someone want to do some tests for me? Trying to check an address for Fueling Mode (PI, DI, Both).

for A01C, can you log 0xFFF8BD33 as an 8bit, and see if it correlates to what would likely be fueling mode (1,2, or 3).

tune A01C defined as:
paramname = Injectors_Mode
paramid = 0xFFF8BD33
databits = 8

always 0

http://www.datazap.me/u/vgi/vishnu-s...=0&data=4-9-16

Td-d, could you pls also look at this param, the values don't make sense to me.

paramname = Manifold_Relative_Pressure
paramid = 0xFFF88F78
isfloat = 1

Could we get Manifold_Absolute_Pressure ?

[Td-d]

MAP is defined? FFF88F74, or FFF8DB7C.

Can you send me a log of MRP, so I can see what the issue is?

Have you got it correctly scaled?

<conversion units="psi relative" storagetype="float" expr="x*0.01933677" format="0.00" />
<conversion units="bar relative" storagetype="float" expr="x*0.001333224" format="0.000" />
<conversion units="mmHg relative" storagetype="float" expr="x" format="0" />
<conversion units="kPa relative" storagetype="float" expr="x*0.1333224" format="0.000" />
<conversion units="inHg relative" storagetype="float" expr="x*0.03937" format="0.00" />

EDIT: I see you logged it above - I've had a look, you're logging the raw value which is mmHG. When I convert to PSI, looks right.

[vgi]

duh. thanks for pointing out, i didn't look at the RR def file.

and i really gotta clean up my file as I can't find anything in it due to all commented out test and ram params

[steve99]

Originally Posted by Td-d

Whilst driving, or in idle?

was while driving for about 5 min bit of wot as well always zero

[steve99]

Originally Posted by Td-d

Also - can you try unk_FFF8F5A0 for me?

Will try it, is it 8bit any scaling needed ? or is it another address for fuel mode ?

G rom

[steve99]

Originally Posted by Td-d

Also - can you try unk_FFF8F5A0 for me?

Tried that address on G rom

8 bit no scaling

always returned 35 in log on a 30 min drive

[vgi]

for those self tuning, willing to share and participate in open source software there is an updated MafScaling tool proggie:
http://www.romraider.com/forum/viewt...p?f=32&t=10481

[Td-d]

Sigh... ok, back to the drawing board.