BRZ Ts parts

[weederr33]

Originally Posted by kuczynskika

They got a ball joint for some flex... yay...


Sent from my iPhone using Tapatalk

Hmmmmm. They could have at least made the rubber stick out a little more :/

[norcalpb]

Originally Posted by weederr33

Those black STI v bars look like stock braces with a simple rubber sleeve on them. Is there anything actually different?

I think these are the same as the 2015 V bars but black so the rubber sleeve doesn’t look it pooped it’s pants.

[kuczynskika]

Originally Posted by weederr33

Hmmmmm. They could have at least made the rubber stick out a little more :/

yeah they're meh overall... the subaru people say they do things but... eh...

[weederr33]

Originally Posted by kuczynskika

yeah they're meh overall... the subaru people say they do things but... eh...

Good think I bought the strut tower brace instead.



whoops... that's supposed to be a secret...

[johan]

Originally Posted by kuczynskika

yeah they're meh overall... the subaru people say they do things but... eh...

I think they only have the intended result when combined with the flexible draw stiffeners. It's meant to be a complete set.

[JeremyR]

Originally Posted by spike021

I want.. but.. so expensive just for those lol.

i'm thinking of doing it.. someone has to check and see if it fits on 2013-2016 models right?!

[spike021]

Originally Posted by JeremyR

i'm thinking of doing it.. someone has to check and see if it fits on 2013-2016 models right?!

Haha if they don't fit I know someone who'd take them off your hands

[switchlanez]

As of this morning there was only 1 complete set of those cherry blossom front/rear pieces unspoken for, then it'll go on backorder from Japan.

I ended up ordering from this site because shipping was slightly cheaper (for me). They accidentally ordered an extra set in case someone wants it without being on backorder:

https://www.subaruwarehousedirect.co...ing-j1210ca301
https://www.subaruwarehousedirect.co...ing-j1210ca401

Call Drew at 806-798-4000 ext. 361 to ensure you get it.

[JonRZ]

Originally Posted by switchlanez

As of this morning there was only 1 complete set of those cherry blossom front/rear pieces unspoken for, then it'll go on backorder from Japan.

I ended up ordering from this site because shipping was slightly cheaper (for me). They accidentally ordered an extra set in case someone wants it without being on backorder:

https://www.subaruwarehousedirect.co...ing-j1210ca301
https://www.subaruwarehousedirect.co...ing-j1210ca401

Call Drew at 806-798-4000 ext. 361 to ensure you get it.

I’d grab this up if you’re looking for it. My order went trough at Subarugenuineparts and apparently there was only a few stateside.

[norcalpb]

Does anyone know when the ‘18 v bars and draw stiffeners are going to be released?

[Jfheisenberg]

Originally Posted by switchlanez

Got part numbers for the front/rear cherry blossom red accents.

Front Bumper Molding: J1210CA301
Rear Bumper Stripe: J1210CA401

Cheapest prices I found were $195.05 for front, $118.83 for rear:
https://www.subarugenuineparts.com/o...ing-j1210ca301
https://www.subarugenuineparts.com/o...per-j1210ca401

$550.71 for the two parts shipped to NY

[switchlanez]

Originally Posted by Jfheisenberg

$550.71 for the two parts shipped to NY

The 1st set of links I posted (shipping from WA) that you clicked cost slightly more to ship to me than the 2nd set of links I posted (shipping from TX):

https://www.subaruwarehousedirect.co...ing-j1210ca301
https://www.subaruwarehousedirect.co...per-j1210ca401

That still may be expensive for you to ship from TX to NY. I'd look for parts websites based near your area. The parts may cost a little more than the two sites I posted (and definitely cheaper than dealerships) but shipping should be a lot less.

[weederr33]

Originally Posted by norcalpb

Does anyone know when the ‘18 v bars and draw stiffeners are going to be released?

You can already find the draw stiffeners on Japan Parts. I don't see why they'd be different from the '18 model.

[norcalpb]

Originally Posted by weederr33

You can already find the draw stiffeners on Japan Parts. I don't see why they'd be different from the '18 model.

Because shipping is $50 for each item and it’ll take like 2 weeks to get. If there’s a USDM version I bet I could save some money. And the new versions are black with a black sti logo. I want as few visible sti logos on my car as possible.