04-16-2023, 01:58 PM | #113 |
Senior Member
Join Date: Jun 2014
Drives: frs
Location: Gunsai
Posts: 4,901
Thanks: 7,281
Thanked 2,940 Times in 1,782 Posts
Mentioned: 23 Post(s)
Tagged: 2 Thread(s)
|
|
04-16-2023, 08:15 PM | #114 |
Senior Member
Join Date: Mar 2018
Drives: 17 Asphalt 86
Location: Ottawa
Posts: 2,232
Thanks: 1,767
Thanked 2,326 Times in 1,174 Posts
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
|
There's a post buried somewhere with a good right up.
Pull the two bolts holding the slave on-top of the transmission and move it a little, the rubber boot comes off to show the fork going to the clutch. Take a finger worth of grease and reach down and Dab around around the pivot joint. Should only take about 15 minutes. Last edited by RToyo86; 04-16-2023 at 09:51 PM. |
The Following User Says Thank You to RToyo86 For This Useful Post: | Teseo (04-16-2023) |
04-22-2023, 11:10 AM | #115 |
Senior Member
Join Date: Mar 2018
Drives: 17 Asphalt 86
Location: Ottawa
Posts: 2,232
Thanks: 1,767
Thanked 2,326 Times in 1,174 Posts
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
|
Did pads and rotors all around; took a minute to properly clean up the wheels.
Car got a bath, helped a friend prep a car for a ceramic coating then out for drinks. |
04-22-2023, 08:28 PM | #116 | |
Proud of BOXER
Join Date: Dec 2012
Drives: Subaru Boxer
Location: Bay Area
Posts: 8,151
Thanks: 7,083
Thanked 6,853 Times in 3,677 Posts
Mentioned: 199 Post(s)
Tagged: 0 Thread(s)
|
Wow those wheels really POP now! Looks stunning.
__________________
Quote:
|
|
The Following User Says Thank You to Clipdat For This Useful Post: | RToyo86 (04-23-2023) |
04-24-2023, 12:58 AM | #117 |
Senior Member
Join Date: Mar 2018
Drives: 17 Asphalt 86
Location: Ottawa
Posts: 2,232
Thanks: 1,767
Thanked 2,326 Times in 1,174 Posts
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
|
Ordered some odds and ends for the drivetrain. Exedy OEM clutch+flywheel, OEM flywheel bolts and battle garage TOB kit with versus fork and pivot.
Car has 125,000km which is in TOB goes boom territory.. |
The Following 3 Users Say Thank You to RToyo86 For This Useful Post: |
04-25-2023, 06:50 PM | #118 |
Senior Member
Join Date: Mar 2018
Drives: 17 Asphalt 86
Location: Ottawa
Posts: 2,232
Thanks: 1,767
Thanked 2,326 Times in 1,174 Posts
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
|
These shipped blazingly fast or they forgot to send me the tracking info. Got a notification yesterday a shipping label was created in Japan; today they're on my doorstep.
Took some detailed photos for anyone Curious. Also confirms these are likely the same STi mounts based on the stamped Subaru badging on the rubber. I want mugen tape |
The Following User Says Thank You to RToyo86 For This Useful Post: | villainous_frx (04-25-2023) |
04-25-2023, 08:23 PM | #119 |
Off to the track!
Join Date: Mar 2020
Drives: '14 Lava 86, '13 WRB BRZ
Location: Canada
Posts: 715
Thanks: 1,638
Thanked 1,191 Times in 478 Posts
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
|
Curious to hear your impression between the current bushing inserts you have and the full replacement.
|
The Following User Says Thank You to villainous_frx For This Useful Post: | RToyo86 (04-26-2023) |
04-27-2023, 09:54 PM | #120 |
Senior Member
Join Date: Mar 2018
Drives: 17 Asphalt 86
Location: Ottawa
Posts: 2,232
Thanks: 1,767
Thanked 2,326 Times in 1,174 Posts
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
|
Not a great picture.. but
Installed TRD engine and trans mounts. Was fortunate a friend lent me his lift; took me around 2 hours to do everything. Driverside mount was the most PITA but I did it kevinvo method without removing the header. Only immediate intial impressions but I am quite pleased with lessened slop and NVH actually dropped after pulling out the OEM trans mount with whiteline insert. I was getting weird IAM drops with my tune around 3000RPM under harder throttle in 5-6th gear with the whiteline insert. Need to do further logging/monitoring but that issue seems to be gone now. Gentle driving is less jerky with changes to throttle Inputs, the shifter also doesn't wooble around as much. |
The Following 6 Users Say Thank You to RToyo86 For This Useful Post: | Clipdat (04-28-2023), Racecomp Engineering (04-28-2023), RedReplicant (05-06-2023), Teseo (04-28-2023), tomm.brz (04-28-2023), villainous_frx (04-27-2023) |
04-30-2023, 11:23 PM | #121 |
Senior Member
Join Date: Mar 2018
Drives: 17 Asphalt 86
Location: Ottawa
Posts: 2,232
Thanks: 1,767
Thanked 2,326 Times in 1,174 Posts
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
|
Impressions update. Put a couple hundred kilometers on the car already since mounts were installed. Highly recommend the full combo together; very OEM+. I wish I did this one sooner. These killed 95% of the NVH I was noticing.
The throttle feels more refined and responsive; engine pulls nice and strong to redline. Shift quality and feel is best it's ever been; with both carrier bushings + mtec springs I think this about as good as the OEM shifter can get. This type of driving I notice the change the most in town. Throttle/clutch engagement is smoother letting me shift quick and smooth while short shifting under load. Last edited by RToyo86; 05-01-2023 at 12:03 AM. |
The Following 4 Users Say Thank You to RToyo86 For This Useful Post: | autoracer86 (05-01-2023), DarkSunrise (05-01-2023), KMA KiCKz (04-30-2023), villainous_frx (04-30-2023) |
05-01-2023, 11:07 AM | #122 | ||
Senior Member
Join Date: Apr 2015
Drives: Subaru BRZ
Location: UK
Posts: 6,075
Thanks: 7,718
Thanked 6,264 Times in 3,515 Posts
Mentioned: 26 Post(s)
Tagged: 2 Thread(s)
|
Quote:
Quote:
Best mod, as it took out the sloppiness in the drive. Engine/drive and the body all feeling as one.. I haven't noted any new NVH that is normally associated with such upgrades. |
||
The Following 2 Users Say Thank You to JD001 For This Useful Post: | RToyo86 (05-20-2023), villainous_frx (05-01-2023) |
05-06-2023, 02:03 PM | #123 |
Senior Member
Join Date: Mar 2018
Drives: 17 Asphalt 86
Location: Ottawa
Posts: 2,232
Thanks: 1,767
Thanked 2,326 Times in 1,174 Posts
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
|
First nice day after a week of rain.
Tossed on the new mirror, I will need to readjust to wide-angle, my brain warps everytime I look at it. Start the day with a morning detail. Did a coating decontamination wash to freshen up hydrophobics and remove mineral deposits/water spotting. Before/after photo testing carpro spotless. I went over the entire car after this to get rid of smaller spots you can only see when the paint was wet(which grab water and ruin the hydrophobics ) Water test after panels decontaminated. Last edited by RToyo86; 05-07-2023 at 09:06 AM. |
The Following User Says Thank You to RToyo86 For This Useful Post: | tomm.brz (05-16-2023) |
05-11-2023, 09:40 PM | #124 |
Senior Member
Join Date: Mar 2018
Drives: 17 Asphalt 86
Location: Ottawa
Posts: 2,232
Thanks: 1,767
Thanked 2,326 Times in 1,174 Posts
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
|
I did a parts run today and completed the Buy once cry once; clutch edition.
• Exedy clutch/flywheel • OEM flywheel bolts • BG TOB • Front bearing cover • 1281 sealant/blue loctite • OEM TOB clips • Verus fork and pivot |
The Following 2 Users Say Thank You to RToyo86 For This Useful Post: | Clipdat (05-16-2023), villainous_frx (05-12-2023) |
05-16-2023, 12:55 AM | #125 |
Senior Member
Join Date: Mar 2018
Drives: 17 Asphalt 86
Location: Ottawa
Posts: 2,232
Thanks: 1,767
Thanked 2,326 Times in 1,174 Posts
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
|
CSG touring arrived and installed. Pretty mellow overall, need to wait for breakin for final impressions but makes a nice noise in cabin.
I will try to get outside rollers whenever I have some time. Last edited by RToyo86; 05-17-2023 at 09:25 AM. |
The Following User Says Thank You to RToyo86 For This Useful Post: | JBezugs (05-17-2023) |
05-18-2023, 08:27 AM | #126 |
Senior Member
Join Date: Mar 2018
Drives: 17 Asphalt 86
Location: Ottawa
Posts: 2,232
Thanks: 1,767
Thanked 2,326 Times in 1,174 Posts
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
|
A little on ramp acceleration fun, Used my dashcam and my phone as audio for the second clip since I think it provides better audio.
Don't mind the banging noise.. had the rear seats down and a full load of detailing junk in the back flying around that I was trying not to send through the windshield |
The Following User Says Thank You to RToyo86 For This Useful Post: | Racecomp Engineering (05-18-2023) |
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Drift shoot with Ryan's 2jz FRS | Amillionoh7 | Scion FR-S / Toyota 86 GT86 General Forum | 0 | 07-28-2016 10:11 AM |
Ryan Tuerck shift knob | ChrisP | Cosmetic Modification (Interior/Exterior/Lighting) | 12 | 01-22-2016 08:38 PM |
Ryan Tuerck’s Street FRS | Sideways&Smiling | Scion FR-S / Toyota 86 GT86 General Forum | 1 | 10-01-2014 11:07 AM |
Ryan Higa owns an FRS? | tekkenman | Off-Topic Lounge [WARNING: NO POLITICS] | 13 | 06-21-2013 06:48 PM |
FAO Ryan | GeeTee86 | AFRICA | 4 | 05-31-2013 10:46 AM |