|
Electronics | Audio | NAV | Infotainment Anything related to in-car electronics, navigation, and infotainment. |
|
Thread Tools | Search this Thread |
10-24-2013, 12:50 PM | #1 |
A.K.A. Starlord
Join Date: Oct 2013
Drives: 2015 Series.Blue
Location: Illinois
Posts: 1,842
Thanks: 845
Thanked 2,099 Times in 834 Posts
Mentioned: 30 Post(s)
Tagged: 3 Thread(s)
|
Sound System Upgrade - Lots of Questions from a Relative Newbie
Hi guys. This will be my first real post on this forum, so I'll quickly introduce myself. I'm 24, and I've owned exactly ONE car my entire life: a 1998 Subaru Legacy Outback Limited with an auto trans (blah!), which currently has 276,000 miles on the odo.
If things work out the way they are supposed to work out, I will be acquiring a brand new BRZ in the next few months. I am a bit of an audiophile, and I enjoy good sound. While I'm also a car nut in general, and I've done plenty of modifications to the Legacy (sway-bars, wheels, tires, brakes, etc...) I have decided that my first project with the BRZ will be to upgrade the sound system. My experience with this sort of job is... minimal. I replaced the head unit in my Legacy, and upgraded all the speakers, and replaced the factory sub-woofer under the seat with a better amp/sub all-in-one unit. The result was some seriously great (relatively) sound, but I'm ready to take things to the next level and do a PROPER system in this BRZ. I've started doing research and things have quickly gotten completely overwhelming, so I decided to start a thread here and start asking annoying questions so I can do things right. I would GREATLY appreciate any help you guys can give me. So, to start off with, here are some [long-winded] questions: 1. Speakers. The speaker locations and sizes already have me confused. My Legacy just has four 6" speakers, four 2" tweeters, and a sub. It was pretty straightforward. Looking at the BRZ, it has all kinds of speaker sizes. Offhand it appears as though there are 4 different sizes. Tweeters and larger 4" speakers on the dash, 6" speakers in the doors, and smaller "rear fill" speakers that most people say are pointless and should be removed entirely. What are people's thoughts on that? In addition, the front dash-mount locations have me worried about sound quality. I was thinking that the sound reflecting off the windshield would likely sound odd and tinny, and some quick research shows I'm not the only person with that concern. Some people say "it's fine" whereas others go so far as to fabricate custom molds to hold the speakers and point them into the cabin. I'm not afraid to tear into the car, but I'm not particularly interested in fabricating custom speaker mounts (mostly because I don't really have enough experience or tools to do it in a manner that will satisfy my requirements as far as maintaining an OEM look, as some others have managed to accomplish.) What should I be expecting in terms of sound from these locations? 2. Wiring. In my current car, I simply re-used all of the stock wire. However, I want to do things properly this time, which means adding a dedicated amplifier. I imagine this means running new wires throughout the vehicle. Can someone explain a basic setup to me? Would I basically be running RCA cables from the head unit to the amplifier, and then regular speaker wire out of that to all the speakers in the vehicle? Could I splice into the factory wires so that I don't have to run new wires in the doors, or should I plan on yanking out ALL the old wire and just starting fresh? I have done a fair bit of dis-assembly in my current car (wires under kick panels, dAmplifier in the doors) but I haven't ever messed with running NEW wires into and out of the doors, for example. 3. Parts. What basic parts am I looking for? Again, I am NOT looking for a system that will rattle my trunk. I listen to all sorts of music, but my family was raised classical, so I am looking for something that I can turn up the volume, close my eyes, and sound like I'm in the MIDDLE of a full orchestra, and then just as easily play crappy dubstep without distortion, or blast Queen. So offhand, the parts I am thinking I will need are: - Crapload of wire - 2 tweeters - 2 mid-range? full range? speakers for the dash - 2 woofers in the door - (nothing, in the rear speakers?) - 1 10" or so woofer in the trunk off to the side - 1 amplifier (multi-channel? how many channels do I need?) - Do I need crossover stuff, or is that taken care of in the amplifier? I don't even know what a "good" brand is. I can't afford to spend $500 for each individual speaker, but I'm willing to spend more than $70 as I did for a pair of Pioneers with tweeters in my current car. Are Pioneer/Kenwood/etc... "good" brands in the same way that Black and Decker is a "good brand?" (In other words, the best of the cheap brands?) 4. Electrical upgrades. I've heard a lot of talk about a "big three" upgrade - I am aware of what that means. Is that necessary since I'm not putting together an earth-pounding 5,000W sound system? Thanks once again to anyone who might have actually had the patience to read this thread and offer some initial tips and insight to help me get started on this research. I think my biggest issue is that every time I find some "guide" that I hope will answer all of my questions, it tends to be a guide on how to install a sound system for competition, which means 40 subs, and 3 amps, and taking up the entire trunk with equipment, and that turns me off. I still plan on daily-driving and tracking this BRZ, and I am not about to add 300 lbs of equipment to the car, nor do I want to compromise the trunk in any way other than with a custom-fitted sub-woofer enclosure off to one side. In fact, other than that sub, I don't want anyone to be able to TELL that the sound system is modified. The only weight I intend to add to the vehicle is that of a sub-woofer, an amplifier hidden away somewhere and some sound insulation in the doors. I also don't intend on removing the spare tire. Last edited by Stang70Fastback; 10-24-2013 at 01:41 PM. |
The Following User Says Thank You to Stang70Fastback For This Useful Post: | Prog (10-25-2013) |
10-24-2013, 01:15 PM | #2 |
Member
Join Date: Dec 2012
Drives: Toyota GT86
Location: Germany
Posts: 94
Thanks: 6
Thanked 17 Times in 15 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
Take a look at this thread click especially into the gallery that is linked.
Just to give you some ideas on it. It is a 1,25 inch tweeter, 4inch midrange, 6,5 inch midsub and 10inch subwoofer in the back. Amplifiers are a 5 Channel amp (4x80Watt plus 1x300Watt) and a 2 channel amp (2x150Watt) Cables: Tweeter and Midrange with 2,5qmm, MidSub and Sub with 4qmm. all cables in sleeves I run the system active since I have a DSP with active crossover. If you do not want to invest that much money, you can work with passive crossover. |
10-24-2013, 02:59 PM | #3 |
Member
Join Date: Jan 2010
Drives: Toyota GT86
Location: Europe, Belgium
Posts: 71
Thanks: 20
Thanked 12 Times in 11 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
related to the location of the tweeters.
They are specifically positioned so the reflection on the windscreen gives the same effect as tweeters that are directly pointed in to the cabin. I know toyota has specific requirements for tweeter location to make sure that the soundwaves are always go inwards the cabin and prefferably to the driver. So i don't think it nessecary to make custom molds for them. Upgrading them should do the trick. And for the wiring , i would replace all the wires because the more connections you have the more chance you have on a bad connection and 1 bad connection can mess up the sound quality due to a change in resistance. Also All audio units from OEM's are tuned to have the best possible sound with the OEM's installed system. So if you go to a complete new setup make sure you have an equalizer in the system so you can tune it to your liking. |
10-25-2013, 06:02 AM | #4 |
Member
Join Date: May 2013
Drives: 2013 Subaru BRZ WRB AT
Location: Columbus Ohio
Posts: 78
Thanks: 1
Thanked 23 Times in 20 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
First off, Welcome to the forum and congrats on picking an 86!
As a recommendation, you may want to read posts at http://www.diymobileaudio.com/forum/ The entire site is dedicated to upgrading your car stereo yourself and has a lot of good people with experience doing what you are setting out to. There are several 86 owners that post there as well. On to the questions: 1. Speakers: On the dash we have a 1" tweeter and a 4" mid range, in the doors are a 6.5" mid bass, and as rear fill we have a 4" in a cavity. Most people say do not bother with the rear fill for simplicity. It's a lot easier to tune just a front stage. On the flip side, rear speakers allow for tuning options that will improve the front sound stage greatly. I have rear fill in my BRZ. As to the dash speaker, they are put there on purpose. They will sound wonderful there. One thing you will want to start with is sound deadening and sealing up the doors. The is a lot of rattle to the doors on the 86's. As to what brand of speakers to look at, on diyma there are a lot of people that really like dayton audio speakers. http://www.parts-express.com/brand/dayton-audio/301 They are fairly inexpensive and sound good. I have not heard them myself, just sharing what I have heard from others. 2. Wiring: Factory speaker wire tends to be really thin. You can improve a factory stereo by just replacing the wiring. There is a noticeable difference. You will want to get wire and run your own. Take a look at the build logs stickied at the beginning of this sub-forum. Several have routing paths laid out for speaker wires. 3. Parts: 1 pair 1" tweeter in dash 3-4" mid range in dash(3" can be easier to fit in) 6.5" mid bass for the doors Rear fill can be added later if you feel there is something missing Sub, go with a prebuilt like a JL Stealthbox and a sub that fits your budget amps(I'd recommend two 4 channel amps, you can bridge 2 channels for the sub) headunit(Stock BRZ does not have RCA output) sound deadener(inexpensive and easy to DIY with big bang to sound quality) DSP(I would recommend getting one with auto-tuning as a good starting point) The DSP will act as a crossover for each speaker. It will allow you to time align each speaker for the best sound imaging and clarity. This may be the most expensive part listed. I recommend looking for a used one with auto tuning and 8 channel output. I can't stress enough the importance of sound deadener. Removing the rattles from areas of the car that are prone to. Also you may want to look into something like hushmat wave breakers which breaks up sound waves directed at it for right behind the 6.5" in the doors. This will prevent the sound waves in the door from reflecting back into the speaker that they originated from causing a little distortion. 4. Electrical upgrades: Not needed. You can replace the factory amp in the trunk with one of the new amps and place the second one at the other inside corner by cutting some foam out. You will not have touched your spare tire or have blocked access to it. I hope this helps. Don't be afraid to ask questions. The only stupid question is the one not asked. Last edited by Zippy; 10-25-2013 at 06:35 AM. |
10-25-2013, 12:30 PM | #5 |
A.K.A. Starlord
Join Date: Oct 2013
Drives: 2015 Series.Blue
Location: Illinois
Posts: 1,842
Thanks: 845
Thanked 2,099 Times in 834 Posts
Mentioned: 30 Post(s)
Tagged: 3 Thread(s)
|
Thanks very much for the information. It seems every question I get answered leaves me with ten more questions though.
I certainly don't mind adding rear fill speakers if it doesn't add too much complexity. However, I'm trying to understand how all the wiring will be run, and it's really this that has me most curious. I'm running through the layout in my mind and this is what I've come up with: I will be running one or two large gauge wires from the battery into the trunk which will power the two amplifiers. Then I have audio from the head unit which will also run into the trunk. This goes to the DSP, and then to the amps. From there it's a simple case of running wires from the amps to the speakers. Now, when you suggested two four channel amps, and bridging two channels for the sub, this is where I start getting confused. Q1: I assume a four channel amplifier can drive four sets of speakers, so when you suggest two four channel amps, that means I have 8 channels. If I use all of the factory speaker locations and add a sub-woofer, I end up with a need for 9 channels. Do the tweeters not use their own channels? Q2: I'm also having trouble understanding how the DSP works. I know the goal of the DSP is to time each speaker so that they are all "shifted" to be equidistant from the listener in order to help clarify the sound. However, since this is only feeding audio to the amp, the only way I can see this functioning is for it to delay various frequencies in the audio stream. How does this pan out with aligning sound to individual speakers? Of course, some people tell me this time correction isn't necessary anyway, so now I don't know who to believe! Q3: Dayton Audio seems to have a crap-load of speakers, and if they sound good, I suppose I could use those. However, are there speakers that are better suited to automotive applications? For example, I have noticed in a lot of builds that nobody uses those cups (baffles?) that go behind the speaker to protect it from water that drips into the door. At least I haven't noticed that in any of the builds I have looked at. I'm guessing it's a sound quality thing, but it makes me wonder whether or not I need to get speakers that are designed for cars, and therefore designed to get wet. I couldn't see any "application specific" speakers on their site. Just tons of sizes and specifications! Q4: One issue I am always worried about when running my own wires is electrical interference. I see a lot of people bundling the power wires right along-side all of their audio cables. If you buy shielded cable, which is what I assume everyone is using, then do you pretty much not have to worry at all about where you run the wire? Last edited by Stang70Fastback; 10-25-2013 at 12:59 PM. |
10-25-2013, 02:17 PM | #6 | |
KCCO From Canada
Join Date: Oct 2012
Drives: Asphalt FRS
Location: The Great White North
Posts: 424
Thanks: 160
Thanked 72 Times in 61 Posts
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
|
my answers are in bold under your questions
Quote:
|
|
10-25-2013, 02:29 PM | #7 |
Member
Join Date: May 2013
Drives: 2013 Subaru BRZ WRB AT
Location: Columbus Ohio
Posts: 78
Thanks: 1
Thanked 23 Times in 20 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
Q1: Each speaker is a channel. Left and right. 2 channels for the tweeters, 2 channels for the mid range, 2 channels for the mid bass, and the last channel you will have is sub. When you bridge an amplifier you are combining output of 2 channels to increase the power output. So a left 150 watt channel and a right 150 watt channel bridged will combine power output. The reason to do this is a sub generally will require more power than any other speaker. Also, a sub does not require stereo separation.
Q2: You've got part of what a DSP does. What you are describing is time alignment. Time alignment is a delay of the signal to the speakers. Normally this is measured in milliseconds. The other thing a DSP does is frequency equalization. This allows you to turn down frequency bright spots and add the frequency ranges where your speakers are lacking. This is something that can wait till later if you chose a head unit with a good EQ and time alignment and a set of components with passive crossovers. Those head units tend to be pricy and not offer a lot of other features you may want. Also component speaker can get up there in price. Q3: I brought Dayton Audio up as an example of inexpensive speakers that sound good. There are plenty of brands out there. Go into some car audio stores and listen around. Post on the other forum I mentioned and get some input from there. You may be able to find some near you willing to let you hear their system and chat with you about car audio. That's where you can learn the most at the quickest pace. Q4: I prefer to run power cables down the opposite side of the RCA cables and run insulated speaker wire down both sides. The RCA cables are not amplified so interference there will be most noticeable from my experience. |
10-25-2013, 02:38 PM | #8 | |
A.K.A. Starlord
Join Date: Oct 2013
Drives: 2015 Series.Blue
Location: Illinois
Posts: 1,842
Thanks: 845
Thanked 2,099 Times in 834 Posts
Mentioned: 30 Post(s)
Tagged: 3 Thread(s)
|
My replies are in bold as well.
Quote:
|
|
10-25-2013, 02:46 PM | #9 | |
A.K.A. Starlord
Join Date: Oct 2013
Drives: 2015 Series.Blue
Location: Illinois
Posts: 1,842
Thanks: 845
Thanked 2,099 Times in 834 Posts
Mentioned: 30 Post(s)
Tagged: 3 Thread(s)
|
Replying to Zippy.
Quote:
|
|
10-25-2013, 07:36 PM | #10 |
Member
Join Date: May 2013
Drives: 2013 Subaru BRZ WRB AT
Location: Columbus Ohio
Posts: 78
Thanks: 1
Thanked 23 Times in 20 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
As for the rear fill, correct. Try it out without first. Most people do not notice that the rear fill is missing.
The reason for going active is not that it is simpler. The reason for going active is that you have more control. You can adjust around the physical restrictions of what the speakers produce for sound and end up with an all around better sounding system. Also, what you learn in the car can be applied to the home. For your first DSP, my suggestion is that you get one that allows you to auto tune. That way you can poke around for yourself and see what different adjustments at certain frequencies have on the sound imaging of your system. If you hose something up you can auto tune it back. My BRZ was my first car audio system with a DSP and I will never have another car audio system without a DSP. |
10-25-2013, 07:42 PM | #11 |
A.K.A. Starlord
Join Date: Oct 2013
Drives: 2015 Series.Blue
Location: Illinois
Posts: 1,842
Thanks: 845
Thanked 2,099 Times in 834 Posts
Mentioned: 30 Post(s)
Tagged: 3 Thread(s)
|
Thanks for all the insight Zippy. One last question. Can I ask what your specific setup is, and what equipment you are running? Just as some kind of starting point.
|
10-26-2013, 12:20 AM | #12 |
Member
Join Date: May 2013
Drives: 2013 Subaru BRZ WRB AT
Location: Columbus Ohio
Posts: 78
Thanks: 1
Thanked 23 Times in 20 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
Sure thing, I kinda went overboard on my BRZs stereo. It is pricey. Front stage is Hertz Mille MLK 3 PA, rear fill is Audison Voce 1.1 and 3.0. I have passive crossovers that came with each of the 3" & tweeter sets Audison & Hertz in use. I have an Arc Audio PS8 DSP. There is an Audison Voce AV12 sub. Two Hertz HDP4 amps providing power. For the head unit I'm using a few things, Pioneer AVH-X8500BHS running RCA cables to the DSP and a Pure i20 running toslink fibre optic cable to the DSP. Also there is an item that I want the mentioned in the video only.
I have a build log I've been intending to post, but have not had time to film the last piece. I may post it in the next day or two without the video and add the video at a later time. |
10-26-2013, 12:52 AM | #13 |
A.K.A. Starlord
Join Date: Oct 2013
Drives: 2015 Series.Blue
Location: Illinois
Posts: 1,842
Thanks: 845
Thanked 2,099 Times in 834 Posts
Mentioned: 30 Post(s)
Tagged: 3 Thread(s)
|
*Googles various parts*
|
10-26-2013, 01:49 PM | #14 |
Senior Member
Join Date: May 2013
Drives: FR-S 10 #103 AT
Location: NC
Posts: 1,519
Thanks: 101
Thanked 599 Times in 347 Posts
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
|
Keep in mind that because bass requires far more power than the higher frequencies, you will not need two identical amps. For example, depending on the speaker power handling, you might get a four channel 50 watt/channel amp for the dash and one that is 100 watts/ channel for the bass. One each for the doors and the others bridged for a sub.
__________________
Necessity may be the mother of Invention but Desperation is quite often the father.
“Sex is like Bridge. If you don't have a good partner, you'd better have a good hand.” - Mae West Papa said, "son there's a lot of evil temptations out there. Best to try 'em all so you know which ones to avoid." |
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
I have so many questions about the BRZ Limited sound system | TouchMyHonda | Electronics | Audio | NAV | Infotainment | 26 | 02-20-2014 11:49 AM |
Cost effective way to upgrade sound? | l0aded | Electronics | Audio | NAV | Infotainment | 6 | 02-22-2013 07:50 PM |
Radio and Sound Upgrade Cape Town | Brandon__ | AFRICA | 21 | 01-26-2013 01:42 PM |
A couple of Mods & Sound Upgrade | ravenMTgirl | Electronics | Audio | NAV | Infotainment | 23 | 09-02-2012 01:52 PM |
Newbie detailing questions | Aetyrno | Northwest | 10 | 07-26-2012 11:51 PM |