Visconti EBC - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

Silverdub · 07-04-2013, 10:29 PM

I received my electronic boost controller today. I know how to rig up my hoses but where do i plug it in? I know i need to disconect something but what?

Edit: i believe i dont need to hook up the intake pipe but just the wastegate and compressor, am i wrong?

edit:
,
here is a picture installed.. I did not want to drill any holes in the car just like the rest of the setup, everything is reversible fairly easily.. I will also add a video pretty soon

Sportsguy83 · 07-04-2013, 10:36 PM

Quote:

Originally Posted by Silverdub

I received my electronic boost controller today. I know how to rig up my hoses but where do i plug it in? I know i need to disconect something but what?

Need to disconnect the purge valve solenoid, start reading from this post down.

http://www.ft86club.com/forums/showp...0&postcount=49

Silverdub · 07-04-2013, 10:39 PM

Damn i was wondering where u were! What took you so long to reply??

thanks brahhhh

Sportsguy83 · 07-04-2013, 10:43 PM

Quote:

Originally Posted by Silverdub

Damn i was wondering where u were! What took you so long to reply??

thanks brahhhh

LOL!! You welcome!!

Sportsguy83 · 07-04-2013, 10:57 PM

Quote:

Originally Posted by Silverdub

Edit: i believe i dont need to hook up the intake pipe but just the wastegate and compressor, am i wrong?

After going through the thread I linked, I have the same question. IMHO, the intake port should be plugged. LMK when you find out.

Silverdub · 07-04-2013, 11:00 PM

I asked the wife to blow in that port, cuz i aint blowin nothin, but its sealed and compressor and wastegate are open!

Sportsguy83 · 07-04-2013, 11:02 PM

Quote:

Originally Posted by Silverdub

I asked the wife to blow in that port, cuz i aint blowin nothin, but its sealed and compressor and wastegate are open!

LMAO fuc*ing funny!

GREAT to know!! I am almost set on getting this, EBC FTW!

Silverdub · 07-04-2013, 11:02 PM

Quote:

Originally Posted by Sportsguy83

After going through the thread I linked, I have the same question. IMHO, the intake port should be plugged. LMK when you find out.

Yeah well it did not answer everything but so far it was the most usefull tread. I ll edit my original post here when done eith diy, perhaps install vid

Frs300 · 07-04-2013, 11:05 PM

same ebc i have. how much was it?

Silverdub · 07-04-2013, 11:09 PM

Where did u get yours, and wont ask you how its hooked up u dont even have an engine!

Frs300 · 07-04-2013, 11:10 PM

Quote:

Originally Posted by Silverdub

Where did u get yours, and wont ask you how its hooked up u dont even have an engine!

i got mine from tactrix

http://www.tactrix.com/index.php?pag...mart&Itemid=53

Sportsguy83 · 07-04-2013, 11:38 PM

Quote:

Originally Posted by Frs300

i got mine from tactrix

http://www.tactrix.com/index.php?pag...mart&Itemid=53

Awesome to know!! Might have to use yours and buy you a new one if I cant get it by next Friday...

Frs300 · 07-04-2013, 11:40 PM

Quote:

Originally Posted by Sportsguy83

Awesome to know!! Might have to use yours and buy you a new one if I cant get it by next Friday...

thats fine with me. order it and have it sent to tony lol

Sportsguy83 · 07-05-2013, 12:15 AM

Quote:

Originally Posted by Frs300

thats fine with me. order it and have it sent to tony lol

Thanks. I'll check up with him tomorrow.

07-04-2013, 10:29 PM	#1
Silverdub Boostin' Join Date: Jun 2012 Drives: FRS-T Location: Montreal Posts: 1,042 Thanks: 337 Thanked 489 Times in 241 Posts Mentioned: 4 Post(s) Tagged: 0 Thread(s)	Visconti EBC I received my electronic boost controller today. I know how to rig up my hoses but where do i plug it in? I know i need to disconect something but what? Edit: i believe i dont need to hook up the intake pipe but just the wastegate and compressor, am i wrong? edit: , here is a picture installed.. I did not want to drill any holes in the car just like the rest of the setup, everything is reversible fairly easily.. I will also add a video pretty soon __________________ My custom turbo build up thread! Last edited by Silverdub; 07-13-2013 at 08:57 AM.

07-04-2013, 10:39 PM	#3
Silverdub Boostin' Join Date: Jun 2012 Drives: FRS-T Location: Montreal Posts: 1,042 Thanks: 337 Thanked 489 Times in 241 Posts Mentioned: 4 Post(s) Tagged: 0 Thread(s)	Damn i was wondering where u were! What took you so long to reply?? thanks brahhhh __________________ My custom turbo build up thread!

07-04-2013, 11:00 PM	#6
Silverdub Boostin' Join Date: Jun 2012 Drives: FRS-T Location: Montreal Posts: 1,042 Thanks: 337 Thanked 489 Times in 241 Posts Mentioned: 4 Post(s) Tagged: 0 Thread(s)	I asked the wife to blow in that port, cuz i aint blowin nothin, but its sealed and compressor and wastegate are open! __________________ My custom turbo build up thread!

07-04-2013, 11:09 PM	#10
Silverdub Boostin' Join Date: Jun 2012 Drives: FRS-T Location: Montreal Posts: 1,042 Thanks: 337 Thanked 489 Times in 241 Posts Mentioned: 4 Post(s) Tagged: 0 Thread(s)	Where did u get yours, and wont ask you how its hooked up u dont even have an engine! __________________ My custom turbo build up thread!

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

07-04-2013, 11:05 PM	#9
Frs300 Senior Member Join Date: Oct 2012 Drives: Pile of junk Location: florida Posts: 1,190 Thanks: 264 Thanked 968 Times in 413 Posts Mentioned: 232 Post(s) Tagged: 1 Thread(s)	same ebc i have. how much was it?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Visconti	Ryan86	AFRICA	25	06-04-2013 02:39 PM
@Visconti	Silverdub	Forced Induction	4	04-27-2013 10:38 PM
Visconti	Calum	User/Vendor/Sponsor Reviews, Feedback, Comments	7	03-11-2013 07:02 PM
CEL with Visconti tune	tjdiz92	Issues \| Warranty \| Recalls / TSB	44	09-16-2012 05:04 AM
Visconti stg 1	Hawaiian	Great Lakes	18	08-23-2012 03:11 PM

User Name		Remember Me?
Password