|
Engine, Exhaust, Transmission Discuss the FR-S | 86 | BRZ engine, exhaust and drivetrain. |
|
Thread Tools | Search this Thread |
01-29-2016, 06:49 PM | #1 |
Senior Member
Join Date: Mar 2013
Drives: 2013 FRS
Location: Seattle, WA
Posts: 405
Thanks: 110
Thanked 59 Times in 51 Posts
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
|
Malperformance Catch Can install
I have the Malperformance catch can but having alittle difficulty understanding how to install. any one down to help? The install instructions are on the youtube video for their turbo kit install - [ame="https://www.youtube.com/watch?v=Jxqdb6oArIg"]Scion FR-S / Subaru BRZ MAPerformance Turbo Kit Install | Part 2 - YouTube[/ame] it starts at 4:30 thx guys!
|
01-29-2016, 07:32 PM | #2 | |
Senior Member
Join Date: Jun 2013
Drives: 2023 GR SUPRA,15 FR-S (SOLD)
Location: Philadelphia, PA
Posts: 4,235
Thanks: 3,086
Thanked 2,101 Times in 1,397 Posts
Mentioned: 31 Post(s)
Tagged: 2 Thread(s)
|
Quote:
If you need help the best bet is to contact @MAPerformance I have no doubt they can help you as there customer service is quite good
__________________
*SOLD*OFT Stage 2 UEL E85/Nameless Performance 3 inch axleback with 5 inch mufflers/ TRD CAI / CNT UEL/ Cusco Strut BAR & LHD Brake Stop / "JDM" Toyota Badges / WinJet JDM headlights - DRL MOD from fteightysix.com - 5000K Diode Dynamics HID kit / Diode Dynamics LED interior Lights and sidemarker bulbs / JDM Clear Sidemarkers / Diode Dynamics LED switchbacks/ OLM LED rear turn signals / Tap Turn Relay*SOLD*
|
|
01-29-2016, 07:39 PM | #3 |
Senior Member
Join Date: May 2013
Drives: 2013 FR-S, white, MT
Location: Puyallup, WA
Posts: 30,061
Thanks: 29,122
Thanked 32,202 Times in 16,572 Posts
Mentioned: 709 Post(s)
Tagged: 2 Thread(s)
|
YIKES ....... I see what you mean ...... they talk fast ..........
I'd give them a call and ask them to talk you through the install. humfrz PS, oh ..... I type soooo slow ...... |
01-30-2016, 12:47 AM | #4 | ||
Senior Member
Join Date: Mar 2013
Drives: 2013 FRS
Location: Seattle, WA
Posts: 405
Thanks: 110
Thanked 59 Times in 51 Posts
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Quote:
oh no i know they have awesome customer service. best I've personally seen from any shop! they forwarded me to the video, i just thought you guys would know |
||
01-30-2016, 01:10 AM | #5 | |
Senior Member
Join Date: Jun 2013
Drives: 2023 GR SUPRA,15 FR-S (SOLD)
Location: Philadelphia, PA
Posts: 4,235
Thanks: 3,086
Thanked 2,101 Times in 1,397 Posts
Mentioned: 31 Post(s)
Tagged: 2 Thread(s)
|
Quote:
All I know is that that's the trouble hose people had issues with crawford BPBs coming lose its on the top of the manifold on the left side after you remove the FA20 cover.
__________________
*SOLD*OFT Stage 2 UEL E85/Nameless Performance 3 inch axleback with 5 inch mufflers/ TRD CAI / CNT UEL/ Cusco Strut BAR & LHD Brake Stop / "JDM" Toyota Badges / WinJet JDM headlights - DRL MOD from fteightysix.com - 5000K Diode Dynamics HID kit / Diode Dynamics LED interior Lights and sidemarker bulbs / JDM Clear Sidemarkers / Diode Dynamics LED switchbacks/ OLM LED rear turn signals / Tap Turn Relay*SOLD*
|
|
01-30-2016, 10:14 AM | #6 |
...Just add nauseum
Join Date: Jan 2015
Drives: 2003 (AP1) S2000
Location: Miami, FL
Posts: 545
Thanks: 310
Thanked 784 Times in 335 Posts
Mentioned: 19 Post(s)
Tagged: 1 Thread(s)
|
I made a really sh*tty bitmap that simplifies the hose routing.
Once the MAPerformance can is installed, your PCV system no longer connects to the engine anywhere. Remove the old PCV check valve from the top of the rear passenger side of the engine, make sure to pound the check valve out of it, then reinstall it. The original PCV line runs from rear of block to rear of intake. It will now run from rear of block to the passenger side catch can, leaving the intake manifold port unused. That port needs to route to the BOV with a hose, or if you don't have the turbo, it must be capped and clamped or you will have bad running problems. The original CCV line (front of block behind A/C compressor) used to connect to the intake hose upstream of the throttle body, it will now run under the intake manifold and connect to the driver's side catch can. On the subject of lines connected to the intake manifold, Make sure you clamp the EVAP purge solenoid line (underneath the intake manifold.) in place. If you do not, it will pop off under boost, and you will have starting/idling/running issues. The video instructions say "power steering pump" when they should say "Air Conditioning compressor" but you get the point. That should clear up some location confusion. Everybody makes mistakes. This is a VTA can; it deletes the original pcv system entirely. Your tune will need to compensate for that, as the old tune accounts for airflow through the PCV into the engine under vacuum.
__________________
There are many ways to displace.
-Spartarus Last edited by Spartarus; 01-30-2016 at 10:26 AM. |
The Following User Says Thank You to Spartarus For This Useful Post: | sweetfrs (01-30-2016) |
01-30-2016, 05:03 PM | #7 | |
Senior Member
Join Date: Mar 2013
Drives: 2013 FRS
Location: Seattle, WA
Posts: 405
Thanks: 110
Thanked 59 Times in 51 Posts
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
|
Quote:
|
|
02-01-2016, 11:06 AM | #8 |
Senior Member
Join Date: Aug 2012
Drives: Asphalt FRS
Location: Cottage Grove, MN
Posts: 1,272
Thanks: 669
Thanked 981 Times in 540 Posts
Mentioned: 84 Post(s)
Tagged: 3 Thread(s)
|
Sorry! I just saw this thread now! Did you get it figured out? If not, I can get one of my techs on the phone for you. Just let me know.
|
The Following User Says Thank You to MAPerformance For This Useful Post: | sweetfrs (02-03-2016) |
|
|
Thread Tools | Search this Thread |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Cusco catch can install diagram | wbradley | DIY (Do-It-Yourself) Guides | 52 | 03-02-2016 12:01 AM |
Mishimoto oil catch can install / review | Craig | Engine, Exhaust, Transmission | 0 | 04-11-2014 02:51 PM |
catch can and install day from 11am to 2pm at my place | stockysnail | Northwest | 1 | 03-16-2014 01:27 AM |
Cusco Oil Catch Can Install Help (horizontal type) | Juurian | Engine, Exhaust, Transmission | 2 | 04-29-2013 12:24 PM |
Cusco catch can install | wbradley | Engine, Exhaust, Transmission | 2 | 01-11-2013 12:11 AM |