DIY: FR-S/BRZ Illuminated Door Speakers - Page 2 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

Vanga · 03-03-2013, 10:40 PM

Quote:

Originally Posted by infinite012

You didn't have to cut the moisture barrier... it has that black goop/gummy stuff that will allow you to pull off the moisture barrier and stick it back on.

I'm sure you could definitely take a heat gun to undo that black silicone, do whatever work you need to do and then use the heat gun again to re seal it, I just didn't think about that at the time. Either way it will work.

infinite012 · 03-04-2013, 08:58 AM

You can pull it off without a heat gun. In fact, using a heat gun will just make it a terrible mess.

But yeah, I'm not going to comment on the lights in the door speaker grill since it's not my cup of tea.

Vanga · 03-04-2013, 02:29 PM

Quote:

Originally Posted by infinite012

You can pull it off without a heat gun. In fact, using a heat gun will just make it a terrible mess.

But yeah, I'm not going to comment on the lights in the door speaker grill since it's not my cup of tea.

To each their own!

Imperius · 09-02-2013, 08:11 PM

Can you connect this controller to Acc
so every time you switch the ignition the leds will go on with the rest of the lights ?
OR
do you have to use the remote every time ?

sirisvirus · 03-15-2014, 10:40 AM

👍

Sent from my iPhone using Tapatalk

SixthElement · 03-15-2014, 03:05 PM

Quote:

Originally Posted by infinite012

You didn't have to cut the moisture barrier... it has that black goop/gummy stuff that will allow you to pull off the moisture barrier and stick it back on.

You're correct sir. It would be much better for others who try this to not cut the plastic.

If you simply pull the plastic a little so the black "tar" starts to stretch you can cut it apart with a razor blade and when you are done it sticks right back to itself with no need for a heat gun at all.

Looks cool, good write up!

ojuniour · 05-29-2021, 04:33 AM

and better yet.. you could have just tapped into one of those wires for power instead of running the wires for power source back ..

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
door speakers not working	number1Tango	Electronics \| Audio \| NAV \| Infotainment	23	04-03-2022 08:03 PM
wire routing for door speakers	derka-derka	Electronics \| Audio \| NAV \| Infotainment	6	12-13-2012 10:49 PM
Front door speakers.	Calum	Electronics \| Audio \| NAV \| Infotainment	5	08-11-2012 05:49 PM
Just replace door speakers?	industrial	Electronics \| Audio \| NAV \| Infotainment	0	08-02-2012 03:57 PM
Installed new in-dash, lost sound from door speakers	Nitro	Electronics \| Audio \| NAV \| Infotainment	2	06-04-2012 09:53 PM

03-04-2013, 08:58 AM	#16
infinite012 Banned Join Date: Jan 2013 Drives: 13 DGM BRZ Ltd Location: Williamsburg, VA Posts: 974 Thanks: 294 Thanked 470 Times in 255 Posts Mentioned: 17 Post(s) Tagged: 4 Thread(s)	You can pull it off without a heat gun. In fact, using a heat gun will just make it a terrible mess. But yeah, I'm not going to comment on the lights in the door speaker grill since it's not my cup of tea.

09-02-2013, 08:11 PM	#18
Imperius Member Join Date: Aug 2013 Drives: Subaru BRZ Location: NY Posts: 45 Thanks: 50 Thanked 3 Times in 3 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Can you connect this controller to Acc so every time you switch the ignition the leds will go on with the rest of the lights ? OR do you have to use the remote every time ?

05-29-2021, 04:33 AM	#21
ojuniour Senior Member Join Date: Nov 2018 Drives: Subaru BRZ 2017 Location: New Jersey Posts: 205 Thanks: 3 Thanked 43 Times in 29 Posts Mentioned: 6 Post(s) Tagged: 0 Thread(s)	and better yet.. you could have just tapped into one of those wires for power instead of running the wires for power source back ..

User Name		Remember Me?
Password