|
||||||
| Cosmetic Modification (Interior/Exterior/Lighting) Discussions about cosmetic mods. |
 |
|
|
Thread Tools | Search this Thread |
09-05-2018, 04:37 PM
|
#1 |
|
Banned
Join Date: Nov 2017
Drives: BRZ
Location: The Sun
Posts: 426
Thanks: 30
Thanked 230 Times in 113 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
How is OEM front badge installed at factory?
Front badge fell off.
How is it installed? A) It is taped on, and the 2 prongs just guide pins. B) The prongs are friction fit, and hold the badge in place. If A, what is good tape to stick it back on? Example from stock photo 
Last edited by GrantedTaken; 09-05-2018 at 05:24 PM. |
|
|
|
09-05-2018, 04:41 PM
|
#2 |
|
ಠ_ಠ
Join Date: Jan 2016
Drives: 860 SansOverspray
Location: CA
Posts: 214
Thanks: 166
Thanked 148 Times in 100 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
3m trim tape works wonders.
|
|
|
|
|
09-05-2018, 10:04 PM
|
#3 | |
|
Senior Member
Join Date: Jun 2013
Drives: 2023 GR SUPRA,15 FR-S (SOLD)
Location: Philadelphia, PA
Posts: 4,234
Thanks: 3,087
Thanked 2,101 Times in 1,397 Posts
Mentioned: 31 Post(s)
Tagged: 2 Thread(s)
|
Quote:
It's just it's own toyota equivalent of 3m automotive VHB, the pins are guide pins. I'd use goo gone and/or a 3m eraser wheel and heat and get that area as clean as possible first. Then proceed to reinstall, also the $8 adhesion promoter sponges from 3m make a real difference on how it applies. I've had the JDM badges on my FR-S since 2015 and they show no signs of coming off following that method.
__________________
*SOLD*OFT Stage 2 UEL E85/Nameless Performance 3 inch axleback with 5 inch mufflers/ TRD CAI / CNT UEL/ Cusco Strut BAR & LHD Brake Stop / "JDM" Toyota Badges / WinJet JDM headlights - DRL MOD from fteightysix.com - 5000K Diode Dynamics HID kit / Diode Dynamics LED interior Lights and sidemarker bulbs / JDM Clear Sidemarkers / Diode Dynamics LED switchbacks/ OLM LED rear turn signals / Tap Turn Relay*SOLD*
|
|
|
|
|
|
09-05-2018, 10:34 PM
|
#4 |
|
Senior Member
Join Date: May 2014
Drives: 2017 BRZ
Location: Chicago
Posts: 3,291
Thanks: 1,260
Thanked 2,933 Times in 1,716 Posts
Mentioned: 58 Post(s)
Tagged: 0 Thread(s)
|
I believe there are friction-fit clips over the pins on the underside of the bumper cover (can make it a bit of a pain to remove). Most people that change badges out simply use the 3m tape.
__________________
Second chance build... or whatever it is.
|
|
|
|
|
|
|
|
|
| Thread Tools | Search this Thread |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| is there a oil temp sensor installed from factory? | nEEdLzZz | BRZ First-Gen (2012+) — General Topics | 16 | 09-14-2019 06:23 PM |
| Factory BRZ Front brake calipers and brackets with speed blenders installed. | Joesurf79 | Brakes, Suspension, Chassis | 5 | 07-25-2018 10:16 PM |
| Factory Subwoofer Installed | go2brz | BRZ First-Gen (2012+) — General Topics | 0 | 07-19-2013 09:14 PM |
| BRZ limited has factory installed sound proofing | ebgs500e | BRZ First-Gen (2012+) — General Topics | 36 | 05-27-2013 09:01 AM |
| Removing the 86 badge on the front of the car | Pake1 | Cosmetic Modification (Interior/Exterior/Lighting) | 1 | 06-10-2012 08:37 AM |
