Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB - View Single Post

sirhc · 11-26-2012, 12:34 AM

This is a very simple thing to do took maybe 10 mins and that was with taking pictures. This will cover the basic LED installation and the Swithback LED's

Tools needed. your keys, Philips head, and small flathead screwdriver, zipties
1 move seat all the way back and look under your dash you are going to find relay circled in red and remove the plug circled in blue, you will attach this to the supplied relay, ( ziptied the new relay under the dash)

2.get in your car, put your key in and turn to accessory. you do not need to actually park your car

3.. take your steering wheel and turn your wheels either all the way left or right depending on which side you want to start on.Turn off car remove keys

4.. get out and remove the three screws that hold the bottom of the wheel liner in. you may need to use your small flathead screwdriver behind the head of the screw

5. then you can pry the fender liner back and get to the bulb assy.

6. put your hand in the opening and grab the light assy and turn left and pull it out from the liner

7. put in the bulb you got to replace the your stock ones, before you put it back in your might turn on your park lights to be sure it lights up you can put these in backward and they wont work.

8. put the bulb assy back in turn to the right to lock it back in, put the screws back and repeat steps 2-8 for the other side, and your done

Stock orange

LED orange

LED white

and a video of the swithback working both turn signal and hazard

[ame="http://www.youtube.com/watch?v=RBG_7EtSWyY&feature=g-crec-u"]JWMotoring 2013 FR-S switchback Led turn signals - YouTube[/ame]

yes I changed my rims with in this also.

Thanks
Chris

11-26-2012, 12:34 AM	#1
sirhc Senior Member Join Date: Jun 2012 Drives: fr-s Location: okc,ok Posts: 99 Thanks: 0 Thanked 45 Times in 20 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	DIY JWMotoring LED turn signals This is a very simple thing to do took maybe 10 mins and that was with taking pictures. This will cover the basic LED installation and the Swithback LED's Tools needed. your keys, Philips head, and small flathead screwdriver, zipties 1 move seat all the way back and look under your dash you are going to find relay circled in red and remove the plug circled in blue, you will attach this to the supplied relay, ( ziptied the new relay under the dash) 2.get in your car, put your key in and turn to accessory. you do not need to actually park your car 3.. take your steering wheel and turn your wheels either all the way left or right depending on which side you want to start on.Turn off car remove keys 4.. get out and remove the three screws that hold the bottom of the wheel liner in. you may need to use your small flathead screwdriver behind the head of the screw 5. then you can pry the fender liner back and get to the bulb assy. 6. put your hand in the opening and grab the light assy and turn left and pull it out from the liner 7. put in the bulb you got to replace the your stock ones, before you put it back in your might turn on your park lights to be sure it lights up you can put these in backward and they wont work. 8. put the bulb assy back in turn to the right to lock it back in, put the screws back and repeat steps 2-8 for the other side, and your done Stock orange LED orange LED white and a video of the swithback working both turn signal and hazard [ame="http://www.youtube.com/watch?v=RBG_7EtSWyY&feature=g-crec-u"]JWMotoring 2013 FR-S switchback Led turn signals - YouTube[/ame] yes I changed my rims with in this also. Thanks Chris Last edited by sirhc; 12-04-2012 at 11:01 PM.