Few things -
Put together a quick harness for my CanChecked MCE18 expander. Pretty neat, you can plug it in to USB with the car off and it'll let you configure it as a Haltech Expander, as well as see live sensor data. Popped a hole behind the battery where some stock harness usually mounts on the inside of the car. Now I've got fuel temp and fuel pressure working, I plan on wiring in transmission temp too.
Also, the RE71RS squeezed up a bit on the car.
I finally got around to getting the rear camber up to the -3.2 area from -2.8 by lightly sanding one of the jamb nuts. Checked corner weights, adjusted a little bit, and string aligned the car back to 0 toe all around afterwards.
This is with 3/4 tank indicated and me in it.
Alright, so I went and did the math on the new motor dyno:
199whp NASA average. For the next event (AMP 1/13 and 1/14) I'm classing as follows:
201whp avg
2895lb
+1.0 tire - Bridgestone RE71RS
+0.3 for <=257mm tire size
-0.5 for double wishbone rear
-0.2 for spherical bushings - roll center correcting FLCA ball joint
-0.5 for splitter
I plan to adjust based on how AMP goes.
Current state of the car mod wise:
2015 Subaru BRZ - 37266 miles on chassis
Engine
JDM Honda K24A
OEM K20A2 50* VTC gear
Drag Cartel drop-in cams
Supertech H1021D valve springs, retainers, and valve stem seals
KPower intake manifold and intake
KPower header, ceramic coated
Bosch 74mm DBW throttle body
Winning Formula Buzzyboi throttle body adapter
Perrin 3” catback exhaust
Injector Dynamics ID1050x injectors
Haltech Elite 1500 ECU
OEM K24Z upper timing chain guide
OEM K24Z side timing chain guides
Generic aluminum lower timing chain guide
Generic aluminum timing chain tensioner cover
Doryoku shortened and baffled valve cover with top vent
Radium BRZ CCV catch can
Radium surge tank
Radium fuel pump hanger
Radium fuel filter
Radium fuel pulse damper
Verus radiator w/ Spal fans
Verus radiator duct
Deatschwerks DW300c fuel pump
Lowdoller fuel pressure / temp sensor
Drivetrain
OEM Exedy clutch and pressure plate
KPower aluminum flywheel
Verus clutch pivot
Verus clutch fork
Shortened OEM BRZ 2pc driveshaft
OSGiken 1.5 way LSD
Cusco diff cover
Suspension
949Racing Xida 500lb / 600lb
RacerX rear upper control arms
Perrin 22mm front bar
OEM 13mm rear bar
RacerX rear sway bar end links
Whiteline roll center correction kit
Superpro FLCA bushings w/ caster offset
Perrin steering rack stays
Salasko Racing solid rear subframe and diff mounts
Brakes
2020 BRZ ABS Unit
BRZ OEM PP Brembo brake calipers
Centric PP blank rotors
Stoptech braided lines
CSG C2 brake pads
Wheels
6x Apex EC7R 17x9.5 +40
2x Apex VS5RS 17x9.5 +40
4x OEM GR86 18x7.5 +48
Exterior
Verus Engineering hood vents
Verus Engineering high efficiency wing
4” flat Home Depot Racing splitter
Verus Engineering air dam
JDL front crash bar
Tom’s tail lights
OLM wide mirrors
Shark fin removed
Interior and Electronics
Cage built by TC Design
Sparco Pro Adv w/ PCI racing slider seat mount
Sparco Evo 2 w/ PCI racing slider seat mount
Schroth Profi 2 6 point harnesses
Rennscot belt wraps
Lifeline 2.25kg FIA fire suppression system
Beastronix Nanny hard wired to vehicle CAN
NMSTec EPS controller hard wired to vehicle CAN
OMP WRC steering wheel
Works Bell quick release
Cartek battery isolator
CanChecked MCE18 CAN expander
Alignment and Ride Height
132mm / 138mm
-5* front camber / -3.2* rear camber
0 toe front and rear