Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB - View Single Post - How to install Crawford Performance Billet Power Blocks (video?)

Mr. · 04-14-2014, 01:51 AM

New Video. BC audio was messed up. [ame="https://www.youtube.com/watch?v=jcsOr1RlfMw&list=UUOo7XX5p4bbt5L5hAW0R73A"]How to Install Crawford Performace Power Blocks BRZ FRS GT86 - YouTube[/ame]

Stuff you needs.

remove engine cover.

Remove PVC line. It pops right off.

Passenger side

remove these 3 bolts.

remove clips.

more clips.

remove things that could be in your way. I removed my sound generator all ready. You might have to as well. Do whatever it takes to give you more slack to move the manifold.

Remove the two bolts holding down the fuel rail guard.

Couldn't get a good pix because wires were in the way. Anyhow, it is the bolt that I am pointing to.
[IMG]https://scontent-a-ord.xx.fbcdn.net/hphotos-ash3/t1.0-9/10153122_10202017379095817_7403278889224711536_n.j pg[/IMG

After take off the bolts, remove the fuel rail guard.

Driver side.
Remove this bolt.

Remove two bolts holding the fuel rail guard.

remove fuel rail guard.

I had to cut bottom clip to give me more slack to move the manifold.

Remove the 6 bolts holding down the manifold.

Prepare the blocks by putting the gaskets in. Note, the gasket is faced down when they are installed in the car.

A trick for sliding them in is to move manifold left and right. If you cannot move the manifold left and right see what other clips or wires that are in the way and loosen them.

After the blocks are installed. Set up the PVC line. The top and bottom can be pulled. The line will become longer. Pull and make sure it is long enough to fit in. Next zip tie both ends.

Final steps reverse the remove and steps. Install the the new hardware and spacers.

[ame="https://www.youtube.com/watch?v=Y__zfaBT7G8"]How to install Crawford Performance Billet Power Blocks BRZ FRS GT86 - YouTube[/ame]

Sorry about the music. I like to listen to something when I work.

Review:It works well with the tune from Shiv. unequal length headers + Blocks on octane 93. 2nd and 3rd gear pulls feels great. MPG I have not noticed any drop. Sound I think it has cleared up my Borla headers and N1 But I could be crazy

Enjoy.

04-14-2014, 01:51 AM	#1
Mr. Supra Senior Member Join Date: Oct 2012 Drives: AE86 & BRZ Location: Merica maryland Posts: 877 Thanks: 717 Thanked 491 Times in 288 Posts Mentioned: 38 Post(s) Tagged: 2 Thread(s)	How to install Crawford Performance Billet Power Blocks (video?) New Video. BC audio was messed up. [ame="https://www.youtube.com/watch?v=jcsOr1RlfMw&list=UUOo7XX5p4bbt5L5hAW0R73A"]How to Install Crawford Performace Power Blocks BRZ FRS GT86 - YouTube[/ame] Stuff you needs. remove engine cover. Remove PVC line. It pops right off. Passenger side remove these 3 bolts. remove clips. more clips. remove things that could be in your way. I removed my sound generator all ready. You might have to as well. Do whatever it takes to give you more slack to move the manifold. Remove the two bolts holding down the fuel rail guard. Couldn't get a good pix because wires were in the way. Anyhow, it is the bolt that I am pointing to. [IMG]https://scontent-a-ord.xx.fbcdn.net/hphotos-ash3/t1.0-9/10153122_10202017379095817_7403278889224711536_n.j pg[/IMG After take off the bolts, remove the fuel rail guard. Driver side. Remove this bolt. Remove two bolts holding the fuel rail guard. remove fuel rail guard. I had to cut bottom clip to give me more slack to move the manifold. Remove the 6 bolts holding down the manifold. Prepare the blocks by putting the gaskets in. Note, the gasket is faced down when they are installed in the car. A trick for sliding them in is to move manifold left and right. If you cannot move the manifold left and right see what other clips or wires that are in the way and loosen them. After the blocks are installed. Set up the PVC line. The top and bottom can be pulled. The line will become longer. Pull and make sure it is long enough to fit in. Next zip tie both ends. Final steps reverse the remove and steps. Install the the new hardware and spacers. [ame="https://www.youtube.com/watch?v=Y__zfaBT7G8"]How to install Crawford Performance Billet Power Blocks BRZ FRS GT86 - YouTube[/ame] Sorry about the music. I like to listen to something when I work. Review:It works well with the tune from Shiv. unequal length headers + Blocks on octane 93. 2nd and 3rd gear pulls feels great. MPG I have not noticed any drop. Sound I think it has cleared up my Borla headers and N1 But I could be crazy Enjoy. __________________ Build Thread YouTube Channel IG - Fwankyhong Subscribe Last edited by Mr.; 10-15-2014 at 01:17 AM.