Quote:
Originally Posted by StormTrooper
Meaning flkc, iam, afr targets, Load, fueling, pulse widths ect????
Are they still in beta or alpha stage?
|
If you make a text file containing the text below the ******* and call it "logcfg.txt" and have it in root directory of SD card in tactrix it will log the parameters this is for C series USA ROM
anything with a ; at start of line is comment or commented out
It will create a csv file on the sd card , new one each time logging starts
Starts when rpm not 0 and stops when rpm goes to 0.
Mate don't know about alpha beta, its open source. no guarantees its use at your own risk stuff.
If you want something more user friendly with safeguards to stop writing wrong ROM,s and with support and backup I would suggest you look at OFT, Ecutek or a tuner.
not being nasty it just the way it is.
If you want more parameters you will have to beg/borrow/ask on here and or Romraider/ecuflash forums. only the guru's dissassembling code can dig these out.
I personally have OFT and use tactrix as a backup device and for faster logging/flashing but if it all goes pear shaped I have the oft as a fallback or comparision device.
***************************************
type = obd
protocolid = 6 ; ISO15765
mode23txaddrwidth = 4 ; mode23 req format info
mode23txlenwidth = 1 ; mode23 req format info
mode23rxaddrwidth = 0 ; mode23 req format info
mode23uds = 1 ; lets OBD channels know you are using mode23 UDS
sortpids = 1 ; sort these PIDs by value to potentially make for fewer requests (=faster)
calcsampinterval = 1000 ; timing parameter - leave as is - will make default for release version
; here are some known RAM addresses for ROM ZA1JA00C
; addresses are likely different for other ROMs
; you can comment out ones you don't need, but keep in mind that with
; the block read nature of UDS, reading extra parameters that have
; adjacent addresses comes at very little bandwidth (=sample rate) cost
paramname = RPM
paramid = 0xFFF8DB80
isfloat = 1
paramname = accel_pedal_angle
paramid = 0xFFF8922C
isfloat = 1
paramname = throttleplate_angle
paramid = 0xFFF89030
isfloat = 1
;Colby
paramname = MAF_default
paramid = 0xFFF8DB90
isfloat = 1
;TD-d
paramname = MAF_Tdd
paramid = 0xFFF89114
isfloat = 1
paramname = load
paramid = 0xFFF8DB6C
isfloat = 1
paramname = IAT
paramid = 0xFFF8DB8C
isfloat = 1
paramname = advance
paramid = 0xFFF8DB88
isfloat = 1
paramname = KC_learned_value
paramid = 0xFFF8B0AC
isfloat = 1
paramname = fine_knock_correct
paramid = 0xFFF8B14C
isfloat = 1
paramname = feedback_knock_correction
paramid = 0xFFF8B0B0
isfloat = 1
paramname = AFR
paramid = 0xFFF8932C
isfloat = 1
scalingrpn = x,14.7,*
paramname = STFT
paramid = 0xFFF8DB74
isfloat = 1
paramname = LTFT
paramid = 0xFFF8DB78
isfloat = 1
paramname = MAP
paramid = 0xFFF8DB7C
isfloat = 1
paramname = IAM
paramid = 0xFFF816F4
isfloat = 1
paramname = speed_KMH
paramid = 0xFFF8DB84
isfloat = 1
paramname = cool_temp
paramid = 0xFFF8DB70
isfloat = 1
paramname = fuel_press
paramid = 0xFFF8DBA0
isfloat = 1
paramname = lambda
paramid = 0xFFF8DBA4
isfloat = 1
paramname = O2_volt
paramid = 0xFFF8DBA8
isfloat = 1
paramname = O2_curr
paramid = 0xFFF8DBB8
isfloat = 1
paramname = cat_temp
paramid = 0xFFF8DBBC
isfloat = 1
;paramname = ECU_volt
;paramid = 0xFFF8DBC0
;isfloat = 1
paramname = abs_load
paramid = 0xFFF8DBC4
isfloat = 1
paramname = requested_torque
paramid = 0xFFF8B490
isfloat = 1
paramname = engine_load
paramid = 0xFFF89148
isfloat = 1
paramname = ignition_total_timing
paramid = 0xFFF8ADF8
isfloat = 1
paramname = requested_torque
paramid = 0xFFF8B490
isfloat = 1
paramname = gear
paramid = 0xFFF895D9
databits = 8
; experimental parameters below this line
;E_AF_Learning_1_A_StoredExt_E44 FFF815C4
paramname = AF_Learning_1_A
paramid = 0xFFF815C4
isfloat = 1
scalingrpn = x,100,*
;E_AF_Learning_1_B_StoredExt_E45 FFF815CC
paramname = AF_Learning_1_B
paramid = 0xFFF815CC
isfloat = 1
scalingrpn = x,100,*
;E_AF_Learning_1_C_StoredExt_E46 FFF815D4
paramname = AF_Learning_1_C
paramid = 0xFFF815D4
isfloat = 1
scalingrpn = x,100,*
;E_AF_Learning_1_D_StoredExt_E47 FFF815DC
paramname = AF_Learning_1_D
paramid = 0xFFF815DC
isfloat = 1
scalingrpn = x,100,*
;E_AF_Learning_Airflow_Range_CurrentExt_E61 FFF8A788
paramname = AF_Learning_Range_Current
paramid = 0xFFF8A788
databits = 8
scalingrpn = x,100,*
;paramname = evap
;paramid = 0xFFF8DBAC
;isfloat = 1
;broken
;paramname = fuel_level
;paramid = 0xFFF8DBB0
;isfloat = 1
;broken
;paramname = amb_press
;paramid = 0xFFF8DBB4
;isfloat = 1
;-------------triggers---------------
conditionrpn = RPM,0,>
action = start
conditionrpn = RPM,0,==
action = stop