[No Limit Motorsport]

Originally Posted by King Tut

1. Ability to cut boost in case of an overboost or other conditions via the ECU. IMO this is much safer than a stand-a-lone controller.

My GFB EBC does this as well.

2. Ability to raise boost level via cruise control stalk. I have two maps that I can select. Low boost, wastegate spring 6psi, and high boost 11psi. Super easy to change on the fly, takes about 1.5 seconds.

I can raise the boost to any level I want from a touch screen display in the car. I have 6 presets that only take a single button press to cycle through while I have the cruise control turned on.

3. Cost, only $100

Cost was $300, but I get a display that also works as a vacuum/boost gauge and the ability to tune the duty cycle, gain, and sensativity without the need of an EcuTek tuner.

4. Simplicity of use, just have the tuner set it, and forget it. If you were going to raise you boost more than you were tuned for originally, you were going to need a re-tune anyway...

A tune should not just fall apart if you decide to turn up the boost, but I agree that simplicity is probably better for some people.

Can we talk negatives? In order to use EcuTek boost control you have to eliminate the OEM fuel tank vent setup. How about the fact that very few solenoids will work for this setup because you are limited by the fact you are using the OEM fuel tank vent setup to control the EBCS. How about the fact that only a few tuners have actually gotten this to work successfully.

Why do you always take such a defensive stance of every mod you do, even when posts aren't directed at you at all? Its good you like your GFB controller and it works for you. I just fear for the many people who have little automotive knowledge, who than turbo their cars, which is somewhat risky in itself if you don't understand the system, than you throw a user adjusted boost controller into the mix....





1. Ability to cut boost in case of an overboost or other conditions via the ECU. IMO this is much safer than a stand-a-lone controller.

My GFB EBC does this as well.

Not every electronic controller has this feature, and no manual controllers do.

2. Ability to raise boost level via cruise control stalk. I have two maps that I can select. Low boost, wastegate spring 6psi, and high boost 11psi. Super easy to change on the fly, takes about 1.5 seconds.

I can raise the boost to any level I want from a touch screen display in the car. I have 6 presets that only take a single button press to cycle through while I have the cruise control turned on.

You change you boost while your using cruise control? Why do you need 6 boost levels? High, med-high, med, med-low, low?

3. Cost, only $100

Cost was $300, but I get a display that also works as a vacuum/boost gauge and the ability to tune the duty cycle, gain, and sensitivity without the need of an EcuTek tuner.

Cool. I guess this is about the cost of a boost gauge + EBCS. Once the boost is set right you shouldn't need to adjust any of those settings though.

4. Simplicity of use, just have the tuner set it, and forget it. If you were going to raise you boost more than you were tuned for originally, you were going to need a re-tune anyway...

A tune should not just fall apart if you decide to turn up the boost, but I agree that simplicity is probably better for some people.

There are a lot of people out there who don't have the know how to use an electronic controller, who don't care to know, and will screw there car up by using it improperly. After 10 years in this industry I have seen my fair share blown motors due to lack of knowledge.

--------------------------

Can we talk negatives?

In order to use EcuTek boost control you have to eliminate the OEM fuel tank vent setup.

This would negatively effect emissions somewhat. Just like removing a catalytic converter. There is something to be said about a plug-n-play installation though.


How about the fact that very few solenoids will work for this setup because you are limited by the fact you are using the OEM fuel tank vent setup to control the EBCS.

What electronic MAC solenoid doesn't work with this?

Ones that do... Grimmspeed, Perrin, Cobb, AEM, universal MAC valves. I suggest Grimmspeed, Perrin or Cobb since it has the proper connector already on it.

How about the fact that only a few tuners have actually gotten this to work successfully.

Who can't get it to work? If they can't, I suggest finding a competent tuner. My tuner had it setup and working with no issues in minutes. It works PERFECT.

----------------------

One last issue with some (all?) stand-a-lone electronic controllers is they do not have a stored memory built into them, therefore if your battery dies, or you have to disconnect your battery for something, you have to setup your boost controller all over again, more than likely on public roads. With the ECU controlled EBCS the ECU always stores the settings. Than if you throw into the mix an uneducated user who doesn't understand gain and duty cycle %'s it is a recipe for disaster or a trip to someone who knows how to use it.