Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB

		Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB > Search Forums
Search Results

Showing results 1 to 12 of 12
Search took 0.01 seconds. Search: Posts Made By: Eaton PSI

Forum: Engine, Exhaust, Transmission

04-20-2024, 05:44 AM

Replies: 5

87mm High Comp Pistons

Views: 1,129

Posted By Eaton PSI

Sleeves were made by LAsleeve. They'll likely...

Sleeves were made by LAsleeve. They'll likely make you another set if you ask them. Some of the forged piston manufacturers will do custom stuff. Gaskets are trickier... I got greedy and had to...

Forum: Engine, Exhaust, Transmission

04-20-2024, 05:39 AM

Replies: 5

87mm High Comp Pistons

Views: 1,129

Posted By Eaton PSI

It is impossible, so I decided to improvise....

It is impossible, so I decided to improvise. Custom made 90mm 11.5:1 pistons and custom sleeves. Modified OEM head gaskets. Just under 2.2L on the stock crank.

Forum: Engine, Exhaust, Transmission

04-20-2024, 05:25 AM

Replies: 784

FA20 Engine Oiling, Bearings, and Starvation

Views: 377,994

Posted By Eaton PSI

Heat exchanger fitted under filter

Engine running! Oil change is about 5.5L with the sump spacer.
Pressure is good with the big pump. When cold its very high, bottoms out the 100psi gauge at about 1500rpm. I have fitted a heat...

Forum: Forced Induction

03-26-2024, 10:41 AM

Replies: 280

Sticky: FI Dyno thread

Views: 253,637

Posted By Eaton PSI

Harrop supercharged

-Rod/Eaton PSI
-Harrop SC
-98ron
-9psi
-85mm pulley, billet 90mm 11.5:1 pistons (2.2L), custom LAsleeve liners, forged rods, lightened OEM valves, lightened OEM flywheel, WRX oil pump, minor head...

Forum: Engine, Exhaust, Transmission

01-26-2024, 03:48 AM

Replies: 784

FA20 Engine Oiling, Bearings, and Starvation

Views: 377,994

Posted By Eaton PSI

Pickup, brace, baffles and spacer installed.

Pickup, brace, baffles and spacer installed.

Forum: Forced Induction

01-23-2024, 10:21 PM

Replies: 13

Harrop supercharger removed, now won't start?

Views: 4,947

Posted By Eaton PSI

OK, so it seems it was my mistake :bonk: When I...

OK, so it seems it was my mistake :bonk:
When I pulled the supercharger I left the injectors/fuel rails on it. My spare stock manifold had all of the original hardware on it. I am not sure of the...

Forum: Engine, Exhaust, Transmission

01-21-2024, 02:03 AM

Replies: 53

An FA20D failure / diagnosis & repair story...

Views: 23,641

Posted By Eaton PSI

Rod 1 is fed from 1st main bearing. Rod 4 is fed...

Rod 1 is fed from 1st main bearing. Rod 4 is fed from 5th main bearing. Rods 2 and 3 are both fed from 3rd main bearing. It will always be 2 or 3 rod that fails first as they have to share oil.
...

Forum: Engine, Exhaust, Transmission

01-20-2024, 02:01 AM

Replies: 784

FA20 Engine Oiling, Bearings, and Starvation

Views: 377,994

Posted By Eaton PSI

sump spacer and mesh screen

10mm thick sump spacer and new mesh screen in pickup. Mesh is the same pitch as OEM, but much larger area. The spacer has tabs on it that I will probably use to add a brace to the pickup. Vibrating...

Forum: Engine, Exhaust, Transmission

01-14-2024, 06:52 AM

Replies: 53

An FA20D failure / diagnosis & repair story...

Views: 23,641

Posted By Eaton PSI

There are precious few useful parts in one of...

There are precious few useful parts in one of these engines after a blow up! I had similar issues, I had to strip 3 engines to find enough usable parts to do a rebuild. Fortunately one was a crash...

Forum: Engine, Exhaust, Transmission

01-14-2024, 06:26 AM

Replies: 784

FA20 Engine Oiling, Bearings, and Starvation

Views: 377,994

Posted By Eaton PSI

Billet pickup

Change of plan. Billet pickup with 22mm ID tube and a removable/replaceable mesh screen. Tube is longer and aimed at the middle of the sump.
Next to make is a 10mm thick spacer between sump and...

Forum: Engine, Exhaust, Transmission

12-12-2023, 10:06 AM

Replies: 784

FA20 Engine Oiling, Bearings, and Starvation

Views: 377,994

Posted By Eaton PSI

Modified pickup

SRT hemi oil pickup screen with a 1" tube fitted to the stock pickup flange.
It will need a brace attached somewhere, it's a bit longer and heavier than the stock one. I'd hate for it to...

Forum: Engine, Exhaust, Transmission

11-20-2023, 03:09 AM

Replies: 784

FA20 Engine Oiling, Bearings, and Starvation

Views: 377,994

Posted By Eaton PSI

I'm leaving the relief valve stock. On a cold...

I'm leaving the relief valve stock. On a cold start it bypasses at around 110psi. When the oil is hot, the bypass shouldn't have any real influence on pressure.
The timing cover has been opened up...

Showing results 1 to 12 of 12

Forum Jump

All times are GMT -4. The time now is 09:45 AM.

User Name		Remember Me?
Password