follow ft86club on our blog, twitter or facebook.
FT86CLUB
Ft86Club
Delicious Tuning
Register Garage Community Calendar Today's Posts Search

Go Back   Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB > Search Forums
Reload this Page Search Results


Showing results 1 to 12 of 12
Search took 1.65 seconds. Search: Posts Made By: FreshFRS
Forum: Forced Induction 04-03-2014, 02:36 AM
Replies: 697
Views: 273,246
Posted By FreshFRS
that can be slightly mis-leading, the c38 at the...

that can be slightly mis-leading, the c38 at the same boost level, say 9psi for instance, flows more air requiring more fuel and producing the more power because of it. the difference here is some...
Forum: Forced Induction 10-23-2013, 03:53 PM
Replies: 697
Views: 273,246
Posted By FreshFRS
martin82 you could have just let it go, ya,...

martin82 you could have just let it go, ya, vendors shouldn't jump to conclusions the way Gmsii did, but, breaking it down and trolling every part of it is just childish. :thumbdown:
Forum: Forced Induction 10-22-2013, 07:06 PM
Replies: 697
Views: 273,246
Posted By FreshFRS
i have to agree with Calum here, cogged belts on...

i have to agree with Calum here, cogged belts on a separate drive loop should not be breaking belts, unless it was an extremely weak (off brand cheap stuff) or defective belt(s) but that is unlikely...
Forum: Forced Induction 10-19-2013, 01:56 PM
Replies: 697
Views: 273,246
Posted By FreshFRS
i did the math a little while ago and at 13psi...

i did the math a little while ago and at 13psi the C30-94 was spinning at 89krpms, at 9psi the charger should be spinning at 72ish krpm. it's a few pages back in the thread.

CSG Mike,

i...
Forum: Forced Induction 10-12-2013, 01:51 AM
Replies: 697
Views: 273,246
Posted By FreshFRS
:word: that is so true, the guy with the dyno...

:word: that is so true, the guy with the dyno jet said it was a heartbreaker, it reads lowish for the turbo i was running (PTE6262 should be ~470 at the boost i was running), and so did the shop...
Forum: Forced Induction 10-12-2013, 01:40 AM
Replies: 697
Views: 273,246
Posted By FreshFRS
:laughabove: this guy.. any dyno can read high...

:laughabove: this guy.. any dyno can read high or low, it really depends on the settings so either of those dynos could produce the same number depending a variety of conditions and factors, temp,...
Forum: Forced Induction 10-12-2013, 01:32 AM
Replies: 697
Views: 273,246
Posted By FreshFRS
its a much more complicated looking dyna-pak....

its a much more complicated looking dyna-pak. Oem's use flywheel dynos for engine development but they also have chassis dyno's to test drivetrain loss and develop more efficiency that way.
Forum: Forced Induction 10-11-2013, 07:00 PM
Replies: 697
Views: 273,246
Posted By FreshFRS
i've heard of roto-test dynos before, they are...

i've heard of roto-test dynos before, they are pretty rare but we had one up in the area i'm originally from. it read about 15% lower than the dyno-jet. for example i made 440whp in my s2k on a...
Forum: Forced Induction 10-11-2013, 02:31 PM
Replies: 697
Views: 273,246
Posted By FreshFRS
its still not really apples to apples, despite...

its still not really apples to apples, despite borla's shitty collector its still going to be better than the factory catted header that kraftwerks used in testing on pump gas (no cat restrictions)....
Forum: Forced Induction 10-10-2013, 06:06 PM
Replies: 697
Views: 273,246
Posted By FreshFRS
looking at the compressor map on the rotrex site...

looking at the compressor map on the rotrex site .253kg/s at 2.16 would be spinning about 89k and be in the 68-70 thermal efficiency range at that PR the vortech is slightly more efficient, but you...
Forum: Forced Induction 10-08-2013, 04:44 PM
Replies: 697
Views: 273,246
Posted By FreshFRS
i am thinking about doing the same with a C38-71,...

i am thinking about doing the same with a C38-71, Kraftwerks definitely gets my vote thanks to it's offset design. An innovate intake manifold with a plenum in top would shorten the piping route by...
Forum: Forced Induction 10-07-2013, 05:55 PM
Replies: 697
Views: 273,246
Posted By FreshFRS
i agree, you could have it sent to Swaintech and...

i agree, you could have it sent to Swaintech and get them to coat it in BBE which is a semi-gloss black heat radiating coating which could help to a minor degree with cooling. functional and more...
Showing results 1 to 12 of 12

 
Forum Jump

All times are GMT -4. The time now is 04:48 PM.

Contact Us - Toyota GR86, 86, FR-S and Subaru BRZ Forum - FT86CLUB - Archive - Privacy Statement - Terms of Service/DMCA Policy - Top

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
User Alert System provided by Advanced User Tagging v3.3.0 (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.

Garage vBulletin Plugins by Drive Thru Online, Inc.