Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB

		Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB > Search Forums
Search Results

Showing results 1 to 13 of 13
Search took 0.00 seconds. Search: Posts Made By: j123ic

Forum: Forced Induction

03-25-2016, 12:54 PM

Replies: 4,960

Edelbrock E-force Owner's thread and FAQs (Frequently Asked Questions)

Views: 1,474,342

Posted By j123ic

For those of you with idle / drivability issues,...

For those of you with idle / drivability issues, check your fuel injectors. They are directional and should only be installed at a fixed clocked position. There's a tab on the fuel rail that aligns...

Forum: Forced Induction

03-03-2016, 01:00 PM

Replies: 4,960

Edelbrock E-force Owner's thread and FAQs (Frequently Asked Questions)

Views: 1,474,342

Posted By j123ic

Just to be clear. Do you perhaps mean the "EVAP"...

Just to be clear. Do you perhaps mean the "EVAP" solenoid? It is located located underneath the supercharger and has two ports that require hose clamps. Additionally clamps are required on each hose...

Forum: Forced Induction

02-22-2016, 08:19 PM

Replies: 4,960

Edelbrock E-force Owner's thread and FAQs (Frequently Asked Questions)

Views: 1,474,342

Posted By j123ic

NotSoJDM are you still on the factory 3.25"...

NotSoJDM are you still on the factory 3.25" supercharger pulley?

Forum: Forced Induction

02-21-2016, 01:31 PM

Replies: 4,960

Edelbrock E-force Owner's thread and FAQs (Frequently Asked Questions)

Views: 1,474,342

Posted By j123ic

Might want to liberally apply o-ring lube to ALL...

Might want to liberally apply o-ring lube to ALL of your O-rings to avoid tears. Going in DRY might have caused them to stick on flat surfaces and fold over. When that happens, I suppose the gaskets...

Forum: Forced Induction

02-13-2016, 04:11 PM

Replies: 4,960

Edelbrock E-force Owner's thread and FAQs (Frequently Asked Questions)

Views: 1,474,342

Posted By j123ic

86fun inspect your front o2 sensor for fouling or...

86fun inspect your front o2 sensor for fouling or damage. If you have a buddy with a BRZ and FR-S, ask if you can swap o2 sensor really quick and log.

This o2 sensor is easy enough to access...

Forum: Forced Induction

02-07-2016, 02:02 PM

Replies: 4,960

Edelbrock E-force Owner's thread and FAQs (Frequently Asked Questions)

Views: 1,474,342

Posted By j123ic

Thanks for the update. I hope that you share this...

Thanks for the update. I hope that you share this information with the Edelbrock calibration engineer assisting you so that they can document this problem. I'm sure they will make an effort to revise...

Forum: Forced Induction

02-06-2016, 01:40 PM

Replies: 4,960

Edelbrock E-force Owner's thread and FAQs (Frequently Asked Questions)

Views: 1,474,342

Posted By j123ic

Please also check the square injector o-rings....

Please also check the square injector o-rings. These also have a tendency to leak with higher vacuum or pressure yet hold at atmosphere. I would also suggest temporarily using distilled water if you...

Forum: Forced Induction

02-06-2016, 01:12 AM

Replies: 4,960

Edelbrock E-force Owner's thread and FAQs (Frequently Asked Questions)

Views: 1,474,342

Posted By j123ic

Making smoke in your situation may be a little...

Making smoke in your situation may be a little more complex than you think. Diagnosing leaks of this nature requires a special type of smoke that can be seen with ultra violet light. Smoke machines...

Forum: Forced Induction

02-05-2016, 04:43 PM

Replies: 4,960

Edelbrock E-force Owner's thread and FAQs (Frequently Asked Questions)

Views: 1,474,342

Posted By j123ic

^ sorry I might have missed it. But I have a ton...

^ sorry I might have missed it. But I have a ton of experience searching for vacuum leaks on superchargers. Can you explain in detail what procedure you are using when using a smoke tester? Also what...

Forum: Forced Induction

01-21-2016, 11:00 AM

Replies: 4,960

Edelbrock E-force Owner's thread and FAQs (Frequently Asked Questions)

Views: 1,474,342

Posted By j123ic

Honestly there's a whole lot more than 9 owners...

Honestly there's a whole lot more than 9 owners now.

And if anyone ever has an issue with missing parts, just call Edelbrock tech support directly. They will more than likely send you what's...

Forum: Forced Induction

10-03-2015, 12:43 PM

Replies: 4,960

Edelbrock E-force Owner's thread and FAQs (Frequently Asked Questions)

Views: 1,474,342

Posted By j123ic

Nitro22, do you think some spacers to move the...

Nitro22, do you think some spacers to move the crash beam forward would've worked?
Perhaps trimming the foam attached to the front may be required after doing this, but I recall that foam being...

Forum: Forced Induction

09-06-2015, 11:26 PM

Replies: 4,960

Edelbrock E-force Owner's thread and FAQs (Frequently Asked Questions)

Views: 1,474,342

Posted By j123ic

Hate to beat this horse to death even more. But...

Hate to beat this horse to death even more. But if you can't understand why it's so important to have it installed at a shop, it's a good thing you went with another kit. Others have already given...

Forum: Forced Induction

09-02-2015, 10:18 PM

Replies: 4,960

Edelbrock E-force Owner's thread and FAQs (Frequently Asked Questions)

Views: 1,474,342

Posted By j123ic

This only applies to people running day time...

This only applies to people running day time running lights as well. Just to be clear, the hole is already there. It's just enlarged to accept a rivet nut.

The instructions can be a bit...

Showing results 1 to 13 of 13

Forum Jump

All times are GMT -4. The time now is 07:01 AM.

User Name		Remember Me?
Password