follow ft86club on our blog, twitter or facebook.
FT86CLUB
Ft86Club
Delicious Tuning
Register Garage Members List Calendar Search Today's Posts Mark Forums Read

Go Back   Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB > Search Forums
Reload this Page Search Results


Showing results 1 to 13 of 13
Search took 0.00 seconds. Search: Posts Made By: Racecomp Engineering
Forum: Suspension | Chassis | Brakes -- Sponsored by 949 Racing 03-25-2024, 10:52 AM
Replies: 45
Views: 14,750
Posted By Racecomp Engineering
You could do that but I would verify your...

You could do that but I would verify your installation first. I'll take a picture of where I'm at tomorrow with the same springs and OEM mounts (if I get over this cold).

Any coilover and...
Forum: Suspension | Chassis | Brakes -- Sponsored by 949 Racing 03-20-2024, 04:01 PM
Replies: 45
Views: 14,750
Posted By Racecomp Engineering
Ahhh okay...I thought those were RCE T2 settings!...

Ahhh okay...I thought those were RCE T2 settings! My bad. Though I think KW V3s have gone through a slight update since then (2012) .

They might be useful as a starting point, though I think you...
Forum: Suspension | Chassis | Brakes -- Sponsored by 949 Racing 03-19-2024, 09:07 PM
Replies: 45
Views: 14,750
Posted By Racecomp Engineering
Our recommended settings won't really have any...

Our recommended settings won't really have any relevance to your KW V3s...they're valved differently and with different spring rates so I don't think I can give you anything to go on.

That...
Forum: Suspension | Chassis | Brakes -- Sponsored by 949 Racing 03-12-2024, 01:57 PM
Replies: 45
Views: 14,750
Posted By Racecomp Engineering
That's an odd mix up from KW, but if he got the...

That's an odd mix up from KW, but if he got the measurements right then it's okay.

I'm using the exact same springs as you but with OEM top mounts and I'm about 25mm lower than OEM with room to go...
Forum: Suspension | Chassis | Brakes -- Sponsored by 949 Racing 03-11-2024, 12:55 PM
Replies: 45
Views: 14,750
Posted By Racecomp Engineering
Do you have a picture of the coilovers assembled...

Do you have a picture of the coilovers assembled with the camber plates but not on the car?

- Andrew
Forum: Suspension | Chassis | Brakes -- Sponsored by 949 Racing 03-10-2024, 01:09 PM
Replies: 45
Views: 14,750
Posted By Racecomp Engineering
It's probably the way he put the camber plates on...

It's probably the way he put the camber plates on the front. You should not use the purple cone piece if you're using the camber plates.

- Andrew
Forum: Suspension | Chassis | Brakes -- Sponsored by 949 Racing 03-09-2024, 10:34 PM
Replies: 45
Views: 14,750
Posted By Racecomp Engineering
Do you have a pic of the coilover assembly before...

Do you have a pic of the coilover assembly before it was installed on the car?

- Andrew
Forum: Suspension | Chassis | Brakes -- Sponsored by 949 Racing 12-24-2023, 12:32 PM
Replies: 45
Views: 14,750
Posted By Racecomp Engineering
I think you'll be plenty happy with the V3s with...

I think you'll be plenty happy with the V3s with the 5/6 springs for an all around fun set up. You could add swaybars later if you feel like you need it.

- Andrew
Forum: Suspension | Chassis | Brakes -- Sponsored by 949 Racing 12-23-2023, 05:50 PM
Replies: 45
Views: 14,750
Posted By Racecomp Engineering
It doesn't matter too much to be honest, both...

It doesn't matter too much to be honest, both will work. The 170 is a tiny bit lighter. Especially in the rear, you have a lot of thread on the coilover and the longer spring won't limit the ride...
Forum: Suspension | Chassis | Brakes -- Sponsored by 949 Racing 12-22-2023, 01:17 PM
Replies: 45
Views: 14,750
Posted By Racecomp Engineering
Right different valving for V3 and CS. ...

Right different valving for V3 and CS.

50-200 front and 60-170 rear is exactly what I run on my car. It'll be good. :)

- Andrew
Forum: Suspension | Chassis | Brakes -- Sponsored by 949 Racing 12-21-2023, 03:28 PM
Replies: 45
Views: 14,750
Posted By Racecomp Engineering
Apologies, earlier I said 60-200 but 60-170 is a...

Apologies, earlier I said 60-200 but 60-170 is a better choice for the rear. I'm using 60-170 in rear with OEM top mounts

- Andrew
Forum: Suspension | Chassis | Brakes -- Sponsored by 949 Racing 11-01-2023, 02:26 PM
Replies: 45
Views: 14,750
Posted By Racecomp Engineering
OEM top mounts just improve comfort and will be...

OEM top mounts just improve comfort and will be quiet. The KW camber plates are pretty good in that regard, but nothing will be as good as OEM.

You could also use the Pedders top mounts that are...
Forum: Suspension | Chassis | Brakes -- Sponsored by 949 Racing 10-31-2023, 10:08 AM
Replies: 45
Views: 14,750
Posted By Racecomp Engineering
KW V3 with 5k/6k rates and OEM top mounts would...

KW V3 with 5k/6k rates and OEM top mounts would be my recommendation. Or just the front camber plates if you want more than -2.2 degrees camber in front.

I'm on a similar set up right now with KW...
Showing results 1 to 13 of 13

 
Forum Jump

All times are GMT -4. The time now is 02:03 PM.

Contact Us - Toyota GR86, 86, FR-S and Subaru BRZ Forum - FT86CLUB - Archive - Privacy Statement - Terms of Service/DMCA Policy - Top

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
User Alert System provided by Advanced User Tagging v3.3.0 (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.

Garage vBulletin Plugins by Drive Thru Online, Inc.