follow ft86club on our blog, twitter or facebook.
FT86CLUB
Ft86Club
Delicious Tuning
Register Garage Members List Calendar Search Today's Posts Mark Forums Read

Go Back   Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB > Search Forums


Showing results 1 to 28 of 28
Search took 0.03 seconds.
Search: Posts Made By: matt88
Forum: Engine Swaps 11-30-2021, 08:17 AM
Replies: 25
Views: 1,505
Posted By matt88
I had another play with the fuel pump PWM output...

I had another play with the fuel pump PWM output of the e38 today.

As it was putting out 128hz and my fans were also set at 128Hz I gave it a long shot that perhaps changing the fan frequency may...
Forum: Engine Swaps 11-25-2021, 09:56 AM
Replies: 25
Views: 1,505
Posted By matt88
Well I had some fun today doing fuel pump...

Well I had some fun today doing fuel pump controller tests.

Disclaimer: I'm using the canbus translator from AGT engineering. I'm not sure of what effect this translator has on the waveform that...
Forum: Engine Swaps 11-24-2021, 12:02 AM
Replies: 25
Views: 1,505
Posted By matt88
Good point! But, if I have the ability to...

Good point!

But, if I have the ability to drive it dynamically and not always slam it at full speed for its entire life, why not give that a go?
Forum: Engine Swaps 11-23-2021, 08:28 PM
Replies: 25
Views: 1,505
Posted By matt88
Great! Thanks for the tip!

Great! Thanks for the tip!
Forum: Engine Swaps 11-23-2021, 12:18 AM
Replies: 25
Views: 1,505
Posted By matt88
Hehe yeah I guess! My thinking is that if my...

Hehe yeah I guess!

My thinking is that if my pump is going to use circa 16-17 Amps at full speed and I add an extra 20% (thus my 20 amp idea) and the controller can survive this for say two hours...
Forum: Engine Swaps 11-22-2021, 10:42 PM
Replies: 25
Views: 1,505
Posted By matt88
Brilliant! Thank you. Might get one and load...

Brilliant! Thank you.

Might get one and load it up with a good 20 amp load for a few hours and see if it survives.
Forum: Engine Swaps 11-21-2021, 09:21 PM
Replies: 25
Views: 1,505
Posted By matt88
Hopefully my awesome baffles and foam setup...

Hopefully my awesome baffles and foam setup combined with the in-basket regulator doing it's supply/return function continuously with a ZL1 pump is going to be as close to a surge style solution as I...
Forum: Engine Swaps 11-21-2021, 08:02 PM
Replies: 25
Views: 1,505
Posted By matt88
Removing the stock regulator from the hanger...

Removing the stock regulator from the hanger assembly, showing it to suppliers, none of them are able to provide a replacement regulator in the same packaging that provides 58 psi and 250 lph flow.
...
Forum: Engine Swaps 11-21-2021, 11:57 AM
Replies: 25
Views: 1,505
Posted By matt88
The pump/hanger assembly is cheap and easily...

The pump/hanger assembly is cheap and easily found.
And because I'm making a completely new tank from aluminium.
And because there will be zero doubts as to whether or not it will be suitable for...
Forum: Engine Swaps 11-21-2021, 11:13 AM
Replies: 25
Views: 1,505
Posted By matt88
Stock pwm fuel pump controller capacity, max current throughput etc

Does anyone know what the limits are on the stock pwm fuel pump controller in our machines?

I'm talking maximum current throughput at 100% pwm duty cycle, or max wattage rating etc?

I'm...
Forum: Engine Swaps 09-14-2021, 12:46 AM
Replies: 17
Views: 1,543
Posted By matt88
Yeah I guess! I will have a dig around and...

Yeah I guess!

I will have a dig around and see if they are easy to find around here.

Wikipedia says it was built by Getrag?
Forum: Engine Swaps 09-13-2021, 10:17 PM
Replies: 17
Views: 1,543
Posted By matt88
Well you COULD, but then it would be auto, if...

Well you COULD, but then it would be auto, if that's your thing. I don't think there were ever any manual trans used in the ES/IS350, Mark X etc.

The Rayhall page linked above says they used the...
Forum: Engine Swaps 09-13-2021, 09:05 PM
Replies: 17
Views: 1,543
Posted By matt88
Yeah have definitely seen this one around the...

Yeah have definitely seen this one around the web. Thanks for the links!

I tried contacting Turbofast but alas no response so far. I think this is a build in North Queensland, Cairns area.

I...
Forum: Engine Swaps 09-13-2021, 05:55 AM
Replies: 17
Views: 1,543
Posted By matt88
Lucky you! I don't know exactly when, but I...

Lucky you!

I don't know exactly when, but I already know I'll be buying an Emira. I don't think it will be in the first year or two of production. Maybe a few years from now. That car is going to...
Forum: Engine Swaps 09-04-2021, 10:24 PM
Replies: 87
Views: 6,592
Posted By matt88
What pressures have you been happy with on the...

What pressures have you been happy with on the Federal RS-R's? You said 25% lower than the Michelin but not sure what pressure you started with.

Just had a quick look online. RS-R's not available...
Forum: Engine Swaps 09-02-2021, 11:06 PM
Replies: 17
Views: 1,543
Posted By matt88
Yeah that GR is close to me, so I'm sure they'd...

Yeah that GR is close to me, so I'm sure they'd be a good source of info. I'll try sending them a message and see what comes back.

Yeah 1UZ could be fun. Might be a little harder to find though....
Forum: Engine Swaps 09-02-2021, 08:19 PM
Replies: 17
Views: 1,543
Posted By matt88
I haven't really thought about that one much. But...

I haven't really thought about that one much. But yes, the LY7 could be a good candidate. There are LFX engines available brand new here, also. You can get a brand new crate LFX and 6L50 auto for...
Forum: Engine Swaps 09-01-2021, 02:12 PM
Replies: 17
Views: 1,543
Posted By matt88
Ashikabi, thank you for responding. Yes,...

Ashikabi, thank you for responding.

Yes, understood the logic/reasoning of an LS swap will likely give more bang for buck. Actually I'm about 70 to 80% complete on my current LS3 swap. Pretty...
Forum: Engine Swaps 09-01-2021, 05:13 AM
Replies: 3
Views: 728
Posted By matt88
Hmmm you might be onto something there!

Hmmm you might be onto something there!
Forum: Engine Swaps 09-01-2021, 05:13 AM
Replies: 17
Views: 1,543
Posted By matt88
Toyota 2GR & 1GR Engines: Truck/Torque/low redline Vs Car/Power/race/high redline

As I'm new to understanding engines I'm trying to understand more what makes an engine an engine, particularly in the Toyota 2GR/1GR world.

Here in Australia there is an abundance of 1GR and 2GR...
Forum: Engine Swaps 08-30-2021, 08:09 PM
Replies: 3
Views: 728
Posted By matt88
K24 + A760 E trans ?

Anyone considered a force fed k24 with an A760E trans?

Thinking outside the box for next project. Maybe a force fed K24 and I'd like it to be auto so wonderwife is more happy. Don't think the...
Forum: Engine Swaps 08-30-2021, 07:59 PM
Replies: 2
Views: 382
Posted By matt88
Brilliant! Thank you!

Brilliant! Thank you!
Forum: Engine Swaps 08-30-2021, 01:03 AM
Replies: 2
Views: 382
Posted By matt88
Heater core connections, inlet and outlet

Silly/simple question, however which is the inlet and which is the outlet on the heater core? I'm at the "connect heater to LS3" stage.

Can I assume the small markings on the hoses tell the...
Forum: Engine Swaps 08-06-2021, 08:37 AM
Replies: 10
Views: 1,092
Posted By matt88
Why not keep it simple (and relatively cheap). A...

Why not keep it simple (and relatively cheap). A 3 inch steel shaft with 1350 joints from Denny's for 700 bucks. From the issues I hear from aluminium and carbon shafts maybe its just easier to go...
Forum: Engine Swaps 12-21-2019, 05:33 AM
Replies: 20
Views: 10,412
Posted By matt88
What would you think if I said I was considering...

What would you think if I said I was considering going for an LT1 instead? Do you think you would be able to provide a harness and able to get your interface to work? I am guessing it would be an E67...
Forum: Engine Swaps 12-03-2019, 05:06 AM
Replies: 20
Views: 10,412
Posted By matt88
I probably won't use Holmart now. No matter how...

I probably won't use Holmart now. No matter how much I ask Mick nicely he seems stubbornly stuck on the fact that he doesn't want to tell me when his engines were manufactured. Even telling him one...
Forum: Engine Swaps 11-20-2019, 07:03 AM
Replies: 20
Views: 10,412
Posted By matt88
Thanks for the response toddy101. Yes, it's a...

Thanks for the response toddy101. Yes, it's a shame the fires up this way at the moment.

It's good to know you also used Holmart. It gives me peace of mind I'm going in the right direction.
...
Forum: Engine Swaps 11-19-2019, 02:39 PM
Replies: 20
Views: 10,412
Posted By matt88
Newb questions... If this translator...

Newb questions...

If this translator replaces the stock ecu, how/where does traditional "engine tuning" get performed? That is, if I take the car to a tuner to perform a tuning service to squeeze...
Showing results 1 to 28 of 28

 
Forum Jump

All times are GMT -4. The time now is 07:41 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2022, vBulletin Solutions Inc.
User Alert System provided by Advanced User Tagging v3.3.0 (Lite) - vBulletin Mods & Addons Copyright © 2022 DragonByte Technologies Ltd.

Garage vBulletin Plugins by Drive Thru Online, Inc.