Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB
Page 2 of 2 1 2
Show 40 post(s) from this thread on one page

Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB (https://www.ft86club.com/forums/index.php)
-   Member's Car Journals (https://www.ft86club.com/forums/forumdisplay.php?f=40)
-   -   1Cor10:23 | Whiteout FR-S | Form Follows Function Build (https://www.ft86club.com/forums/showthread.php?t=64074)

drewbot 05-26-2014 08:58 AM
Quote:
Originally Posted by 1Cor10:23 (Post 1759395)
Was able to get -1.26 on each side. Shop said doubling up could get 1.5+ for sure. I'll run it as is for now since I'm only really doing it for closer to even wear at the track. Likely coils for next season.
That's decent enough. And I'm assuming you aren't rubbing at full lock? I have 17x8 +48 in the front, and based on your 17x9 + 35 up front, it appears I can fit 235's if you can fit 245's :thanks:

1Cor10:23 05-26-2014 10:07 AM
Quote:
Originally Posted by drewbot (Post 1759697)
That's decent enough. And I'm assuming you aren't rubbing at full lock? I have 17x8 +48 in the front, and based on your 17x9 + 35 up front, it appears I can fit 235's if you can fit 245's :thanks:
I'd double check that with others...the offset might be tight? + know that +45 RPF1's barely fit stock and people typically coil it. It's fairly well documented that 17x9+35 clears stock, lots of posts in the 17x9+35 RPF1 thread.

drewbot 05-26-2014 10:19 AM
Quote:
Originally Posted by 1Cor10:23 (Post 1759731)
I'd double check that with others...the offset might be tight? + know that +45 RPF1's barely fit stock and people typically coil it. It's fairly well documented that 17x9+35 clears stock, lots of posts in the 17x9+35 RPF1 thread.
Yeah I think I did. Not to hijack your thread, but you can use this website to check fitment against a known fitment: http://www.willtheyfit.com/index.php...et2=48#content

drewbot 09-26-2014 10:52 PM
@1Cor10:23

Just ordered Raceseng plates too. Did you DIY or get it installed elsewhere?

Sent from my OnePlus One

1Cor10:23 09-27-2014 04:07 PM
Quote:
Originally Posted by drewbot (Post 1962634)
@1Cor10:23

Just ordered Raceseng plates too. Did you DIY or get it installed elsewhere?

Sent from my OnePlus One
I got them installed at a shop, need to do alignment afterward anyway.

Ryaquinn 10-02-2014 09:21 PM
Great name! Good luck with the build. I started one also... @drifting4jesus build


Sent from my iPhone using Tapatalk

1Cor10:23 12-22-2014 04:56 PM
Ohlins R&T install - coming Spring 2015!

1Cor10:23 12-22-2014 04:57 PM
Mishimoto thermostatic oil cooler install - coming Spring 2015!

1Cor10:23 10-28-2015 10:03 PM
Bumpidy - going to actually keep this up to date for next season...

ottoyu34 01-19-2016 12:13 AM
Build looking sick, any bracing planned?

Hope to meet you soon.

BoWScotland 03-19-2017 07:16 AM
Hi
Could i ask how (what hardware and software) you used to generate the track diagram, car position, speed etc in (the bottom left hand corner) of your great YouTube video of 'September, 2014 - Open Lapping @ TMP - 126.1'
Thanks very much indeed :)

1Cor10:23 02-20-2018 03:46 PM
Quote:
Originally Posted by BoWScotland (Post 2875115)
Hi
Could i ask how (what hardware and software) you used to generate the track diagram, car position, speed etc in (the bottom left hand corner) of your great YouTube video of 'September, 2014 - Open Lapping @ TMP - 126.1'
Thanks very much indeed :)
Sorry for the late reply! It's Harry's lap timer (available on android or iOS).


All times are GMT -4. The time now is 05:02 AM.
Page 2 of 2 1 2
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
User Alert System provided by Advanced User Tagging v3.3.0 (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.


Garage vBulletin Plugins by Drive Thru Online, Inc.