Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB
Page 2 of 4 1 2 34
Show 40 post(s) from this thread on one page

Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB (https://www.ft86club.com/forums/index.php)
-   Cosmetic Modification (Interior/Exterior/Lighting) (https://www.ft86club.com/forums/forumdisplay.php?f=36)
-   -   DIY/Post Your Spec-D Headlamp Pics (https://www.ft86club.com/forums/showthread.php?t=63774)

Chen 07-18-2014 05:53 AM
My question, which nut do I use to adjust the height of the light output?

STS-V 07-18-2014 09:58 AM
Why exactly are these not FI friendly?

ecko04 07-19-2014 12:41 PM
Quote:
Originally Posted by STS-V (Post 1853034)
Why exactly are these not FI friendly?

See post #5

aznknightz17 07-23-2014 06:45 PM
Did you guys use harness for the D2S? @ecko04? Cold start my driver didnt turn on, had to turn off and turn it back on again to let them ignite.

Also like @Chen Im curious which knob is it to aim the headlight up/down

Chen 07-23-2014 09:33 PM
Quote:
Originally Posted by aznknightz17 (Post 1862076)
Did you guys use harness for the D2S? @ecko04? Cold start my driver didnt turn on, had to turn off and turn it back on again to let them ignite.

Also like @Chen Im curious which knob is it to aim the headlight up/down
I figured it out. It's the only 8mm bolt that's back there. Counter clock wise for up and clock wise for down.

My advise do it whole the headlight is off the car. It's a pain while it's on the car


Edit- clock wise for up and counter clock wide for down.

weederr33 10-16-2014 02:07 PM
Sorry to bumb this thread, but I installed these earlier and hadn't seen this mentioned in any of the other threads on them. Do these not have Hi/Lo beams? I'll look to see if I see it in any other threads, but figured I'd start here. Thanks!

jonzhuxD 10-16-2014 02:29 PM
Quote:
Originally Posted by weederr33 (Post 1986383)
Sorry to bumb this thread, but I installed these earlier and hadn't seen this mentioned in any of the other threads on them. Do these not have Hi/Lo beams? I'll look to see if I see it in any other threads, but figured I'd start here. Thanks!
Yes, there is a high/low beam but it's a bit different than stock.

It's a bi-xenon projector setup. The projector inside has a shield that blocks off light above a certain threshold so you don't blind other drivers. When you turn on your high beam, this shield moves down to let all the light shine out of the projector.

There's much more to it but that's a general description.

kennyd8606 08-17-2016 10:53 AM
hi I just got these light install on my frs today but I was wondering how do you wire the led drl strip to stay on without turn on the light switch on in the daytime?!

Chen 08-17-2016 06:30 PM
Quote:
Originally Posted by kennyd8606 (Post 2731137)
hi I just got these light install on my frs today but I was wondering how do you wire the led drl strip to stay on without turn on the light switch on in the daytime?!




DRL like when you put down your e-break and the lights come on? If I remember right, you can't because you take the harness out when you install the new headlights.

FR-S Runner 10-14-2016 09:52 AM
Quote:
Originally Posted by aznknightz17 (Post 1852800)
Kinda need help with this guys, please bare with me. I got the headlights same time as you all but now i just had the chance to installed it on Wed. Long story short got the HID H1 in and after couple mins of messing with the washer, i got it to fit. The long "rod" was upward and the bulb itself on on the bottom if you know what I mean. The output and coverage was quite disappointing, please check and see. Is that what you guys are getting also?

As you can see since the "rod" is above the actual bulb, there is a reflection of it on the wall and also on the ground. Hard to miss it. Should I go get D2S instead?

http://i.imgur.com/8upjjBI.jpg
http://i.imgur.com/8yw2DGO.jpg
How exactly did you fix this? My body shop put these lights on and got the same results.

continuecrushing 10-15-2016 02:46 PM
Quote:
Originally Posted by FR-S Runner (Post 2774750)
How exactly did you fix this? My body shop put these lights on and got the same results.
Are you guys using D2S bulbs? I know with that bulb there is also a D2R that has the rod thing of the bulb in a different spot.
@Diode Dynamics for someone who actually knows lol

Diode Dynamics 10-17-2016 11:28 AM
Quote:
Originally Posted by continuecrushing (Post 2775652)
Are you guys using D2S bulbs? I know with that bulb there is also a D2R that has the rod thing of the bulb in a different spot.
@Diode Dynamics for someone who actually knows lol
D2S is designed for use in OEM projector style housings, D2R is designed for reflector style applications.

Those output shots with the keyholes look like OP is running an H11 in an H11B housing or H11B in H11 housing etc etc

That keyhole is caused by the position of the leadwire on the HID bulb.

Nick C.

FR-S Runner 10-17-2016 07:56 PM
Quote:
Originally Posted by continuecrushing (Post 2775652)
Are you guys using D2S bulbs? I know with that bulb there is also a D2R that has the rod thing of the bulb in a different spot.
@Diode Dynamics for someone who actually knows lol
I was told that there is an h1 bulb in there.

go_a_way1 10-17-2016 08:12 PM
Quote:
Originally Posted by FR-S Runner (Post 2777102)
I was told that there is an h1 bulb in there.
factory is h1

I run D2S in mine they fit fine (there is a adapter to fit the h1)


All times are GMT -4. The time now is 08:59 AM.
Page 2 of 4 1 2 34
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
User Alert System provided by Advanced User Tagging v3.3.0 (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.


Garage vBulletin Plugins by Drive Thru Online, Inc.