TheHapaOne's CBS BRZ Limited
 

Current Mod List:
Interior
-JPM Coachworks Dash/Gauge Hood/Knee Pads/Speaker Panels
-JDM Black Interior pieces http://www.ft86club.com/forums/showp...3&postcount=46
-Anarchy Motive California Gold Shift Knob
-Diode Dynamics RGB footwell lighting
-Yospeed Heated Seat Switch Surround
-Perrin Drift Button/Reverse Lockout
-Full interior LED conversion

Exterior/Engine Bay
-Miro 398 18x8.5 +35 Matte Black
-Driveway Labs Version 1 Diffuser Prototype
-Rally Armor Mudflaps
-Perrin Short Antenna
-Perrin Brake Reservoir Coozy
-Tinted Windows
-Yellow Tinted Headlights and Foglights
-Cut and Blacked out Taillights
-Diode Dynamics LED Front/Rear Blinkers and Boomerang Always On Module
-LED Sidemarkers
-Password:JDM Gold Engine Dress-up
-Password:JDM Gold Battery Tie Down
-Debadged Trunk

Performance
-Perrin 2.75" CAI Powder coated Gold
-Perrin Black Inlet Hose
-Perrin 3" Resonated Catback
-Perrin Master Cylinder Brace
-Perrin Oil Cooler
-Nameless Catted FP/OP Prototype
-Tomei UEL Header
-HKS Hipermax SP Coilovers
-Password:JDM Gold Strut Bar/Diagonal Braces
-ATE Type 200 Dot 4 Brake Fluid
-DBA T2t Front/Rear Rotors
-Project Mu HC-800 Front Pads
-Hawk HPS Rear Pads



Dated Change Log:
7/18/2013 - Swapped side markers with smoked ones
7/19/2013 - Windows Tinted 25% all around
7/27/2013 - Perrin Front License Plate Relocation & Shorty Antenna
CF Vinyl covering on drill holes & Subaru letters debadged
8/5/2013 - Perrin Inlet Tube, Master Cylinder Brace, Drop in Filter
8/6/2013 - Apexi RS Extreme Catback Exhaust
http://i.imgur.com/vzdMzAM.jpg
That 4.8" really fills out the diffuser
8/12/2013 - Installed Perrin Oil Cap/Filter Cover and Master Cylinder Fluid Coozy
Installed OEM Black Shifter boot Bezel and Sport/TSC Buttons
8/13/2013 - Installed JPM Coachworks dash panels & had Eibach springs installed at Derrin's
9/16/2013 - Password:JDM strut kit and dress up kit installed
9/18/2013 - TOM'S USDM taillights installed - swapped to clear lens with @BRZPDX
11/3/2013 - installed nameless catted front/over pipe
11/23/2013 - tinted Headlights & Foglights Yellow Guys at Tommy's Tint did a good job
12/2/2013 - forgestars came in forgot to get Lug Nuts to fit them though :/ size is 18x9 +36 all around
2/22/2014 - after a while of no real mods decided to finish my interior black out
3/26/2014 - Perrin Cold Air intake and Oil Cooler installed
4/4/2014 - Springtime review http://www.ft86club.com/forums/showp...9&postcount=60
4/5/2014 - Drift Office tune
http://i.imgur.com/Ah6SPJP.jpg
Some time in April - Installed DBA rotors and Hawk Pads
11/9/2015 - Installed HKS Hipermax SP Coilovers
2/8/2015- Swapped Perrin 2.5" Catback to Perrin 3" Catback

4/17/2015 - Tomei UEL installed and FT86SF Catted Header Removed...Tuned In Eugene by VitTuned
http://i.imgur.com/4uqniPK.jpg
http://i.imgur.com/3XI1zlZ.jpg
http://i.imgur.com/5LP2Y2J.png
[ame="https://www.youtube.com/watch?v=FSvhSUpCThs"]2013 BRZ Dyno pull/Exhaust Video - YouTube[/ame]
Video Clip for your viewing pleasure

7/21/15 - Forgestars removed Miros installed
7/22/15 - Stickers removed
COMING SOON: Turbo?

Awesome i also have a black brz

Never seen one with a gas cover, and how do you like the diffuser?

Looking good

Diffuser is nice...but not sure it actually does anything just looks good

I honestly hate the gas cover just not willing to pull it off I am planning on getting the JDM trunk applique that matches it if I can find it

I highly recommend installing the clear side markers, they are a must (especially on black)

Have smoked ones they look much better than clear IMO

Good point they probably would look better!

I'll take some pictures of it this weekend and post them up

With the OEM diffuser, will the Perrin tips fit? I haven't seen the diffuser in person, not sure if it would be worth while to install the diffuser if I am planning on installing a Perrin exhaust further down the road. :iono:

I certainly like the look of the OEM diffuser and would definitely install it if it will work with my future mods.

I'll let you know after I install my exhaust which is 123mm

more parts added to the purchased list will be putting all the perrin stuff on today and will take pictures

Installed all the perrin stuff was going to take pictures but my toolbox decided to dump its contents all over the parking lot and I had somewhere to be will be taking pictures tomorrow and posting them up. Car has a noticeably different sound with the drop in filter and inlet tube as well as being quieter in the cabin since the resonator was deleted. Like it so far still making sure I installed it all correctly had some weird sounds but probably just due to increased air flow

Welcome from a fellow Hapa!

added new pictures of exhaust taking pics of engine bay and side markers right now will be posted soon

The Apexi exhaust really filled out the diffuser and gave the car a nice deep voice. Install took about 1 1/2 hours done on some ramps in my carport. I may have to get a torque wrench and torque the front bolts but the fitment seemed good and didn't feel overtighted and I tried to make both bolts even we will see.