hahahahahaha.. It was nice meeting you. Your car looks great, the stance is awesome..

I had a bolt rolling around in my door sill when it was brand new. Brought it back, they tore it apart, pulled it out, reassembled it. The next day I heard another bolt rolling around. This one was harder to find, it was under the carpet, by the seat base. They got that one out too. Turns out that neither had fallen out, both were lost during assembly.. My dash has a very slight rattle, and there is a slight one from the right rear of the passenger compartment. I wasn't expecting it, but it's not horrible. I HATE rattles, but I'd rather drive it than fiddle with it anymore. Odd my 2013 Ram 3500 Diesel is the one with the quiet interior....

I have the same rattle(It happens when you're in neutral slowing to a stop and the rpm is around 1000). It stops if I step on the clutch or move the shifter.

FYI, my CE28N 17x7.5 +50 wheels are for sale. Will include the tires free of charge since they're pretty much done. They're 215/45/17 Dunlop Direzza II.

$1,200 without lug nuts.
$1,300 with Evasive extended open ended lug nuts.

http://i.imgur.com/5w2UhI7.jpg

I'm the black one if you see me in saint paul, mpls, eden prarie areas.

I've seen you around EP, I work there.

There's also a Firestorm FR-S nearby I've seen.

Thank you! I happened to peek as I was driving past and saw your car the other day. How long ago did you purchase yours? I should have wheels on in a month or so, so you'll have to take a look again!

I work there also where are you working? I work for Nexxt Technologies we sell 3D printers.

I got it in March from Carlson Toyota. I will check your car out for sure, what wheels are you getting? I'll check it out for sure!!!

I work at Arrow Electronics, the division I'm in distributes EMC equipment. I'm over near the Wells Fargo and Home Depot.

@neutron256, do you know how to check ECU calibration file with your Tech Stream device?

It looks like calibration ZA1JA01C fixes the DI seals issue. Pretty sure our cars will have the older file, but I'm just curious what our numbers are.

See this page for more info.

http://www.ft86club.com/forums/showt...=40951&page=18

i don't know how but I'm pretty sure I can figure it out. Techstream is pretty user friendly once you get the hang of it. I'll try an check mine this weekend and see which version I have. Then I can start worrying knowing I have the old version. :bonk:

I just realized that you had a tune done, didn't you? Not sure if that changes the file name or not.

Mine is reflashed back to stock because I got sick of dealing with Visconti. Which version of stock I'm not sure though.

I guess I'll find out. I wonder if I can get the latest version by getting an updated tune from Visconti.

That's where I originally went to possibly purchase a car but they low balled me on my trade in and insisted I buy their ultramarine 6speed when I told them I wanted whiteout.. Otherwise it would've taken two weeks to get a whiteout 6speed... So I contacted the guy I bought my tC from at the St. Cloud dealership and went up there two days later... He gave me a better deal on the trade in and I left with the car that day!

Anyway that was a little off topic haha... I'm not 100% sure what I'm getting but I'm looking at some Rotiforms this guy is selling for pretty cheap or some 3sdm wheels. I'm sort of still indecisive still but we'll see in the next month! :)

Well I was planning on going to RK tonight since I haven't been in a couple weeks, but I think this heat is going to be way too much for me.

Anyone planning on going?

I was planning on it but I'm a little afraid of the heat as well...

I'll go if you guys do. Heat doesn't bother me any..

I think I can handle it for a little while. Anyone else?? New people?

Probably not this week. A lil busy at work, and an exam tomorrow. ;)

I don't have anything else to do. Where is RK?

Screw it I'll go for a little while at least.

It's in Brooklyn park just off I94.

-Take exit 31 CR81/ Bottineau Blvd.

-Head north and take the first left onto West Broadway.

-It will curve around and head south. It will be maybe 1/4 mile on your right. If you see the drive in diner on your left where there is a classic car meet you went too far.

It starts at 6pm I'll probably be there by about 6:30

I need to remember to bring a lawn chair with me this time.

Might have to work late hours today so probably not gonna make it :(. I'll be there next week if there are people going.

Brooklyn Park? That's a bit of a long drive. 50/50.

I'm heading out shortly. Hopefully I'll see at least some of you there.

On my way. Save me a spot.

Did you guys melt last night at RKC?

Also, just a friendly heads-up in case you aren't on MNSubaru!

http://www.ft86club.com/forums/showthread.php?t=45364

http://mnsubaru.com/attachments/image-jpg.8804/

It actually wasn't as bad as I expected. Got there early and staked out one of the few spots in the shade. Plus there was a bit of a breeze.

Of course there weren't many cars there to look at. @M3GH4N , @JohnJuan and I all happened to be going the same direction leaving and a fun unplanned cruise down I94.

As for the Open House thanks for the heads up I've marked it on my calendar.:thumbsup:

Spotted a blue FRS on Phalen yesterday, anybody on here?

I was in my white FRS going to ve to climb, made the turn a little sharp/late as I was looking in my rearview mirror thinking how good the car looked! lol

Alright, does anyone know a good place to get dent repairs? I have three I need to get rid of on my BRZ!

Dent Kraft in golden valley.

starting to spot a few frs now. stock white frs on mcknight with asian guy driving. i was the guy who drove up :thumbup: also on white bear ave, asian guy in blue frs. good to see them out! thinking about paying off the 2012 corolla s and getting another frs:party0030:

One for DD, one for the track? That's a good idea!

Okay who's all attending Proving Grounds next weekend?!?

Minnesota Check In
 

Meeeeee!!!!!! And a bunch of other fast Canuck imports

I'm going to try to get up there Saturday morning. Can't promise though. My front pipe will be here Wednesday and *hopefully* the header will be here before Friday. I would like to have those installed before. Ugh!

I'll be there as well, with the same setup as before with the add-on of the GrimmSpeed strut tower brace. Still patiently waiting on the Nameless Header before I decide to purchase their downpipe. Who else is going to compete in the AutoX event?

I know the white sti and maybe the m3 from my group. I'm sticking with the straight stuff this year due to my lack of tires.

Anyone have an inexpensive set of stock wheels?
 

As the title says, I may be interested in a another stock set of wheels for my car for a project. Wheels only. Pm me if u have some that you want to let go of!! I'm in the twin cities. Thanks!