1 Frs + 1 Bunny = No Money!!!!
 

current list of mods either installed or in my garage waiting.

Suspension:
feal coilovers
spc rear arms
wilwood fronts 4 pot
wilwood front lines
stop tech rear rotors
stop tech rear pads
stop tech rear lines
mtech shift springs
hotchkis sways
hotchkis rear end links
whiteline front endinks
White line rear subframe bushings
Whiteline rear diff mounts
Whiteline diff cradle bushings
Perrin psrs bushings in front control arms
Fr-speed brace set
Whiteline roll center kit and tierods
Radium MC brace
Stainless clutch line
Spc camber bolts
Perrin front arm braces

Drivetrain:
fx400 clutch and flywheel.
ts trans mount
ts shifter extension
kartboy ss
kartboy shifter bushing
Shift spring kit
TO delrin knob

Body:
jdl bumper bar
revo-tune japan lip
kmo activities wing
charvionia rear diffuser
trackspec motorsports vent kit
Hood shocks

motor:
ecutek tune flash n go
cusco motor mounts
JDL UEL turbo kit
JDL 3 inch over pipe
JDL 3 inch mid pipe
JDL 3 inch single exit cat back
dw 750 injectors
DW 65c pump
Radium dual can
tial wg
Tial BOV
mishimoto oil cooler
Grimspeed boost solenoid
jdl fan shroud
mishimoto radiator
Wheels:
Mach V gunmetal
255 40 maxxis vr1

Most recent pics.
http://i237.photobucket.com/albums/f...pslmv8mc5a.jpg





here is my other project: a true track car. SOLD
http://forums.vwvortex.com/showthrea...rack-car-build...

bump for a few updates...
still waiting on my coilovers to get installed, too much b.s. going on right now.
here are some better pics:
http://i237.photobucket.com/albums/f...psaecf12f8.jpg
a little more with the old/new theme outside the shop where my bunny is being built.
http://i237.photobucket.com/albums/f...psd784393f.jpg

got some more parts...
flaps are already on, but I am waiting till Wednesday to put the arms on at the same time as the coils and alignment.
http://i237.photobucket.com/albums/f...ps8045c93f.jpg

Which intake from FA20 Club were you not satisfied with?

this one... none of sections are lined up, lots of melt through.
http://i237.photobucket.com/albums/f...ps76578cac.jpg
http://i237.photobucket.com/albums/f...psd3ca8b87.jpg
http://i237.photobucket.com/albums/f...psce3773c0.jpg

Is that their COld Air Intake with the K&N filter?

the only one they make.

Coilovers are on....
[ame="http://vimeo.com/63274591"]2013 Scion FR-S Yonaka Coilover Install on Vimeo[/ame]
before:
http://i237.photobucket.com/albums/f...psaecf12f8.jpg
after:
http://i237.photobucket.com/albums/f...ps674040df.jpg

I also put a set of Spc lower arms on.... one wasn't up to snuff, but I talked to spc today and they are taking care of it.
The adjustment tabs are barely welded on, needless to say one broke off leading to a very expensive alignment.:bonk:

here are pics of the wheels as they sit. I have been getting a lot of questions on the offset and fitment.

http://i237.photobucket.com/albums/f...psda36023b.jpg
http://i237.photobucket.com/albums/f...psbbdce416.jpg
http://i237.photobucket.com/albums/f...ps3f65f493.jpg

I should probably try to fit a set of 225/45/16 or some 215/45/16 tires to avoid possible rubbing under hard driving conditions.

so what are your impressions now with the fixed SPC lower arms?

How is it driving 16's vs. 17's? It looks damn good with 16's

don't have the replacement yet.
16's feel pretty close to 17's to be honest.

You probably get better slightly better gas mileage too right? from the size difference alone

its all but the same overall diameter as stock. It is lighter, at least my back tells me it is, forgot to weigh it officially.