Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB
Page 5 of 5 1234 5
Show 40 post(s) from this thread on one page

Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB (https://www.ft86club.com/forums/index.php)
-   Scion FR-S / Toyota 86 GT86 General Forum (https://www.ft86club.com/forums/forumdisplay.php?f=2)
-   -   FR-S Valve Spring safety recall Ħɞ|| (https://www.ft86club.com/forums/showthread.php?t=132590)

g e 02-25-2019 09:08 PM
Quote:
Originally Posted by humfrz (Post 3179622)
Well, now @Tcoat , that's just not fair, @Ultramaroon and @Sapphireho try real hard - :iono:


humfrz
Did it go faster afterwards?

humfrz 02-25-2019 09:49 PM
Quote:
Originally Posted by g e (Post 3189545)
Did it go faster afterwards?
Ya lost me there - :iono:


humfrz

g e 02-26-2019 11:02 AM
Quote:
Originally Posted by humfrz (Post 3189552)
Ya lost me there - :iono:


humfrz
Did it go faster after you finished doing whatever you were doing while standing in the engine bay? Or was that a picture of someone else?

humfrz 02-26-2019 01:11 PM
Quote:
Originally Posted by g e (Post 3189717)
Did it go faster after you finished doing whatever you were doing while standing in the engine bay? Or was that a picture of someone else?
hmmm.... must have been someone else - :iono:

(or that was a short term memory happening - and I just don't remember - :sigh:)


humfrz

Ultramaroon 02-26-2019 02:56 PM
Quote:
By adjusted I assume you mean valve clearance. I didn’t bother reshimming. They were all still within spec though. More on the loose side than tight. If it was a simple process I would have improved the clearance though. I kind of wrote it off as the valve not seating well, engine being cold and dry and the fact that I was turning it over buy hand rather than by the starter. It was a big discrepancy though and it was all leaking past one intake valve.
I missed all this on the first read. Did you lap all your valves and check them with prussian blue before final assembly?

ermax 02-26-2019 03:25 PM
Quote:
Originally Posted by Ultramaroon (Post 3189806)
I missed all this on the first read. Did you lap all your valves and check them with prussian blue before final assembly?
Nope

Ultramaroon 02-26-2019 04:22 PM
Quote:
Originally Posted by ermax (Post 3189821)
Nope
Oops

ermax 02-26-2019 04:27 PM
Quote:
Originally Posted by Ultramaroon (Post 3189853)
Oops
I didn't rebuild the heads at all. I simply replaced the short block.

Ultramaroon 02-26-2019 04:30 PM
Quote:
Originally Posted by ermax (Post 3189856)
I didn't rebuild the heads at all. I simply replaced the short block.
Oh! Hmmm... o_0

humfrz 02-27-2019 12:53 AM
1 Attachment(s)
Quote:
Originally Posted by Ultramaroon (Post 3189806)
I missed all this on the first read. Did you lap all your valves and check them with prussian blue before final assembly?
Oh, that looks so old school - ;)


humfrz


All times are GMT -4. The time now is 07:01 AM.
Page 5 of 5 1234 5
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
User Alert System provided by Advanced User Tagging v3.3.0 (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.


Garage vBulletin Plugins by Drive Thru Online, Inc.