Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB
Page 1 of 9 1 2345 Last »
Show 40 post(s) from this thread on one page

Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB (https://www.ft86club.com/forums/index.php)
-   Engine Swaps (https://www.ft86club.com/forums/forumdisplay.php?f=92)
-   -   K24 swap pics, It runs off the BRZ brain!!! Video on page 4&7. VVT enabled now! (https://www.ft86club.com/forums/showthread.php?t=138819)

solidsnake11 02-02-2020 07:08 PM
K24 swap pics, It runs off the BRZ brain!!! Video on page 4&7. VVT enabled now!
 
This thread has been Censored

DarkPira7e 02-02-2020 07:21 PM
I'm super excited to see this!

ML 02-02-2020 07:46 PM
Finally got tired of the fa20 piling issues?

Irace86.2.0 02-04-2020 08:29 PM
So you didn't prepare the surfaces by removing paint? Did you remove the oil at least? Did you use a shielding gas on the inside of the pan? Considering the pan isn't structural and doesn't see high forces or pressures, you might be fine. Pics of the inside of the pan?

Irace86.2.0 02-04-2020 11:16 PM
I would just be concerned with porosity on an oil container, but like I said, there is minimal risk of weld fracture from load, pressure, heat cycles, etc, so I’m sure your pressure test will work out.

Grawlix 02-08-2020 04:21 PM
Quote:
Originally Posted by solidsnake11 (Post 3297661)
Two intake cams. The BRZ computer needs both intake signals before it will fire and the exhaust signal can run from the crank since it pulses once every crank revolution.
What's your plan for the wiring/ecu(s)/CAN bus?

Calum 02-08-2020 09:13 PM
Quote:
Originally Posted by solidsnake11 (Post 3297706)
Stock,stock and stock.

Going to use the brz computer, switch some coils, do some wiring, swap some sensors, 8 port injectors and my 76mm throttle body.

Look familiar?

Attachment 184657

Attachment 184658
Ok, that's fucking incredible. Are you doing the tuning yourself?

DIY 02-09-2020 03:04 AM
Great work!

Grawlix 02-09-2020 12:01 PM
Quote:
Originally Posted by solidsnake11 (Post 3297706)
...8 port injectors...
8 functional port injectors or 8 port injectors in the eyes of the BRZ computer?

ML 02-09-2020 12:14 PM
So will you pass inspection if you get it working with the stock ecu? Or are you just track only these days? NC sucks for engine swaps on newer cars.

fika84 02-11-2020 11:02 AM
You're a mad man. Keep up the good work! FOR SCIENCE!

Grawlix 02-11-2020 12:15 PM
Quote:
Originally Posted by solidsnake11 (Post 3297861)
4 port injectors ran by port injection drivers and 4 port injectors ran by the direct injection drivers.
Where will the 4 extras be installed?

wparsons 02-14-2020 10:10 AM
Quote:
Originally Posted by solidsnake11 (Post 3297706)
Stock,stock and stock.
Going to use the brz computer, switch some coils, do some wiring, swap some sensors, 8 port injectors and my 76mm throttle body.

Giving up VTEC? I can't imagine the stock BRZ ECU can handle swapping cam profiles.

Ashikabi 02-14-2020 10:41 AM
Quote:
Originally Posted by wparsons (Post 3298940)
Giving up VTEC? I can't imagine the stock BRZ ECU can handle swapping cam profiles.
Just use a vtec killer setup. Then you're always in vtec

Sent from my ONEPLUS A5010 using Tapatalk


All times are GMT -4. The time now is 09:05 AM.
Page 1 of 9 1 2345 Last »
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
User Alert System provided by Advanced User Tagging v3.3.0 (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.


Garage vBulletin Plugins by Drive Thru Online, Inc.