Nameless Performance Axleback w/ 4" Mufflers
 

Does anyone with the Nameless Performance Axleback exhaust with the 4" mufflers have any sound clips? Youtube isn't really helpful atm as most videos don't even state what muffler size they went with.

Thanks!

Not sure if you're still looking but I'm installing my Namless Axleback on Monday with the 4" mufflers. I'm installing the downpipe/overpipe combo as well with it so it might not be a 100% what you're looking for but I'll upload a sound clip of the system.

I have a fresh one but with 5" mufflers, sorry! :bonk:

I'm looking for some sound clips as well or someone local to Austin TX who has the nameless axle-back 4" muffler, and at this point I would take a listen to the 5" realizing that the 4" will be louder. FWIW my endgame is the nameless down/over and somebody's catted header, either ft86speedfactory or the Nameless, not sure which right now.

Really would like to hear someone's 4" Nameless axle-back in person.

Here is a clip of 5" mufflers at start up and idle.

[ame]http://youtu.be/WX0XJIJQ4xs[/ame]


humfrz

Excellent. Thanks for that vid. now...anybody with 4"? anyone?

also is that the 3" axleback or the 2.5"?

The piping is 2.5".

I don't plan on any other exhaust modifications, so no reason to go larger....;)


humfrz

4" would be loud!!

I wanted a good loud exhaust and was afraid 5" would be to quiet. After talkin to the awesome guys at nameless I went 5". It's perfect. Cold starts are orgasmic, very loud and throaty. It's already almost to loud on cold starts so 4" would be to loud in my opinion. sounds plenty loud when your on the throttle, cruising with partial throttle you don't even hear it. I Can't stress enough how quality this thing is, the sound is perfect, the welds are amazing compared to similar priced exhausts. DO IT, you'll love it.

I have the 5" and it was loud but has mellowed out. It is still rumbles when you press the peddle at low rpms and screams at high rpms. However, I went and ordered UEL catless headers for the ultimate rumble ;-)

Question! How does the Nameless 5" muffler 2.5 axleback sound compared to the 2.5" Perrin? I guess resonated or unresonated, either or. Considering this, but still in a pickle. Leaning more towards the Perrin... but doesn't hurt the shop around!

This was my exact same debate for the longest time. I remember reading that someone heard both of these in person and said the nameless 5" mufflers with downpipe was slightly louder than the perrin unresonated. So I decided to buy a perrin nonresonated catback. I'll post more when it comes in to describe the sound.

Also the nameless was full 2.5" and perrin was also 2.5"

Thats great then this was the exhaust that I was considering whenever I got my twin. My plan was to keep it NA and go with the whole Nameless exhaust, overpipe, and headers.

So again, thanks for the sound clip

Didn't you have a TRD exhaust before?

The Perrin resonated is a lot quieter than the nameless 2.5 w/ 5" mufflers. A local hear switched from one to the other to prepare for the uncatted header he ordered.

it's not too loud whoever said that. it really depends on personal determination how loud is really loud.
I have 4" but havent record anything. if i have a chance i will record it but i have OP,Catted FP as well

I had Perrin exhaust tips before ..... but not TRD.

I was trying to fool myself ...... :D


humfrz

Just wait til you swap out the stock header. I absolutely loved the sound with their front/over pipe. After I installed a header, I lasted 24 hours before putting the stock muffler on.

OP did not mentioned header.

Go for this with nameless.

[ame="https://www.youtube.com/watch?v=XrxfZmRVILY"]https://www.youtube.com/watch?v=XrxfZmRVILY[/ame]

This is what I did...
 

I went full Nameless. Header, down/overpipe catted w/resonator, 5" muffler axleback. All 2.5".

I am quite happy with it.

[ame="https://www.youtube.com/watch?v=HJqbpbZ5L7E"]YouTube[/ame]