Exhaust tips
 

Besides the JDM GT86 exhaust tips, what other options are out there?

[ame="http://www.youtube.com/watch?v=2EjCbsaHSPk"]Acura Integra Duck call exhaust - YouTube[/ame] get one of these.

I have the Perrin tips. They are pretty expensive but honestly the best looking "tip only" option IMHO

Yep, I agree .... they are well made and look great ..... :thumbsup:

http://perrinperformance.com/i-13324...-fr-s-brz.html


humfrz

For a few hundred dollars more...you can get a full exhaust.... pretty expensive tips.

[ame="http://www.amazon.com/DC-EX-1013-Stainless-Resonated-Exhaust/dp/B003D4KA32"]DC Sport EX-1013 Stainless Steel Resonated Slant Cut Bolt-on Exhaust Tip : Amazon.com : Automotive[/ame]

anyone got experience with this set?

I agree a bit on the expensive side but they do look the best out of all the exhaust tips for the stock exhaust.

Here are the DC tips. They looked very nice and I used them until I got my cat-back.

Attachment 68789

Picked them up at Advanced Auto but I'm not sure if they're still selling them.

I agree, but, if one has no intention of changing the exhaust, they look like one did .... ;)


humfrz

THIS! We have a local guy here who is too loud to run autox. He's recently swapped back to the stock muffler and still has the rest of his exhaust. He's going to run the perrin tips for this exact reason. Looks like he still has an exhaust :thumbup:

I got the Perrin and they look a lot better than stock. I just wish I could shove them on a little further as they stick out a bit much for my liking.

I got them because I'd like to go to Borla catback + diffuser, but that's the difference between under $200 for tips or $1000 for what I really want. I'll keep these until I can do the full thing, then sell the tips. Likely they will look just about new at that point too. They are well made.

^ +1 couldn't agree more. I didn't want loud as our cars aren't quiet anyway. But didn't want cheesy either which is what stock is.

hmmmm.......you must like them tucked way back. When I had them on my stock muffler, they could have gone back another 1/2" ... :)


humfrz

When I get my header I'm pretty sure my track pipe will be unbearable. I'll probably have to revert to stock to get it quiet enough. If the sound is acceptable at that point I will be wanting some tips.

Wonder how pilot pm583 will look. Think the straight cut could look good if set to the right depth. Hope so.

How's the rust?

I did a quick DIY a while back to make my own tips using a set of weld on magnaflows that I turned into clamp-ons. Was about $90 all said and done.
http://www.ft86club.com/forums/showt...hlight=exhaust

Link doesn't lead to the DIY.

Scroll down. It was an addition to an old DIY. The original OP deleted it for some reason, but my write up is a few posts down.

I just added an edit so that you get the basic content of the original post.

No problem with rust during the period of time I had them on. They're stainless.

Duck call exhaust are the new whistle tips! WOOOWOOOO!! QUACK!

Here's the link without the context :)
http://www.ft86club.com/forums/showp...1&postcount=11

Gotcha lol didn't see the update at the bottom of your post. Looks sharp

That's only in da mornin'. You 'posed to be up cookin brefas fo somebody and so that's like an alarm clock. Woo WOO

http://tailgunnerexhaust.com
Lol

/thread

What is this fuckery?!

are the screws stainless too?

also, what is the taper like from the outside edge to the inside tube wall? Is it a straight line or curve.

They stick out about an inch to inch and a half. I'd like them a bit closer to even w/ the rear fascia. 1/2 to 1 inch in from where they are would be great.

My favorite tips, being a cyclist, is the bike inner tube:

[ame]http://youtu.be/ieJUP9O9RG8[/ame]

It's a pain, but you can get them to go further in. Mine sat out too far at first as well. Use both hands and twist. They all still sit out further than the perrin catback, but they won't poke out like they probably are now.

http://i62.photobucket.com/albums/h8...pswuonfv6t.jpg

....... :lol: ....... you guys got waaaaaaay too much free time on your hands ..... :D


humfrz

can you post some more side shots?

Let me know if you need more :cheers:

http://i62.photobucket.com/albums/h8...psu80crsrm.jpg

http://i62.photobucket.com/albums/h8...ps7rdwmes4.jpg

I can't claim this one, but I may try it sometime.

That's probably a half inch less stick out than mine. I gave them a good shove, but perhaps when this rain stops I'll try a little harder.

Just remember to twist. Just pushing didn't help. When I started twisting, I was golden. But this is as far as they would go

they stick out way too much. how far do the oem jdm toyota gt86 tips stick out?

lol, mine? They stick out about 1/2 inch…that's about a 1/4 inch further than the perrin catback.

JDM tips

Looks like they stick out about the same

I did that, and I put a small amount of bike grease on them to help them go on. They are sort of butted up against the small detent that is there on the bottom of the exhaust exit pipe. I may still see if they'll go a little more. They've been on for a bit over a month I think.

^ you got a close 3/4 shot?

How is this? 3/4 of my car in Silver, and a friend's whiteout with standard tips
http://s18.postimg.org/bi773k289/photo_7.jpg