Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB - The Exquisite 86's ML24 widebody FA20club turbo build thread

- Member's Car Journals (https://www.ft86club.com/forums/forumdisplay.php?f=40)

- - The Exquisite 86's ML24 widebody FA20club turbo build thread (https://www.ft86club.com/forums/showthread.php?t=56837)

The Exquisite 86's ML24 widebody FA20club turbo build thread

I would like to Thank all my Family and Friends for all their support threw this car build. Huge Thanks to my Sponsors ML24, FA20club, Avant Garde for their amazing customer service and their continued patience with me as i build this Out There FR-S, Special thanks to @kendalldwhite Instagram:StayMinty & Stay Minty FT86 Build Thread and @FR-S FI for their help with everything. As of now this build is kinda on hold for a couple weeks due to work, but plan to get back rolling in a few weeks.

My Build Instagram:Theexquisite86

Thanks
Chris

Current Mod list for my Garage Built 2013 Scion FR-S

I have boxes of parts to be installed just waiting till i finish the body work and vinyl wrap to install them

-Interior-
Sparco chrono seats & bases
Sparco 4 point harnesses
Sparco 325 leather steering wheel
Sparco JDM horn button
Racingspec anodized wheel hardware
NRG quick release
NRG e brake handle & drift button
Ca-Fi double din headunit
Rockford Fosgate 4" component speakers
Rockford Fosgate P3C 12" subwoofer
Rockford Fosgate 1000 watt amp
P3 tunning boost gauge
Custom interior lighting

(Interior parts waiting to be installed)
Subaru JDM rear seat delete
Subaru JDM rearview mirror
Toyota JDM arm rest
Zerg Ind. Carbon fiber dash trim
JPM coachworks gauge hood
Yospeed custom engraved door sills
Rouge Status custom shift & ebrake boots and rear deck
TRD push to start

-Engine-
FA20 turbo kit
-Garrett 60mm T3/T4 turbo
-Tial BOV & Wastegate
-Mishimoto oil cooler & radiator
-Sickspeed oil catch can
-K&N air filter
-E85 flex fuel kit
-High flow Subaru fuel pump, 550cc injector clinic injectors
-FA20 EL ceramic coated headers
-Perrin 3" overpipe
-ISIS 3" catless front pipe
-Tomei Type 80s 3" F/I cat back
Perrin crank pulley
Perrin radiator hoses
Perrin battery tie down, oil cap, oil filter cover
Tanabe engine brace
FT86 speedfactory v brace
Grimmspeed master cylinder brace
Password JDM washer kit
Downstar spike bolt kit
Optima redtop 6pack battery
Custom engine bay lighting
Hellatone supernote horns

-Suspension-
Swift racing prototype lowering springs & swaybars
Whiteline subframe bushings
Whiteline camber bolts & endlinks
Whiteline positive steering kit
Stoptech Stainless brake lines

-Extierior-
ML24 9pc. widebody kit (soon to have the other 7pc carbon
Agency power carbon brake ducts
Aerojacket duckbill trunk
Zn6 shark fin antenna
Toyota JDM badges
Subaru rear under diffuser
Raceseng front & rear towhooks
VR1 Rexspeed concave mirrors
Diode dyanmics custom multicolor led headlights & HID's
Spyder tailights

(Exterior parts waiting to be installed)
TRD carbon fender garnishes
TRD carbon rear window trunk garnish
Stillen roof spoiler
Custom vinyl wrap
Seibon FA style Carbon Fiber hood

-Rims & Tires-
(current set-up)
Enkei Kojins 18x9.5 +38 off
Nitto motiv 235x30x18
Mishimoto red open ended lug nuts

(New set-up on the way)
Avant Garde F220
Falken tires
Downstar Spike Lugs

Sorry for the low quality photos, took them all with my camera phone, will have KBW photography shoot the car when its finished

DAY 1
http://i1359.photobucket.com/albums/...psae438c1e.jpg

LETS TRY BLACK RIMS
http://i1359.photobucket.com/albums/...ps3ae75c61.jpg

NOW LETS GO LOWER
http://i1359.photobucket.com/albums/...psf37a3759.jpg

I LIKE IT ;)
http://i1359.photobucket.com/albums/...ps6e8b5237.jpg

Hmmm...
http://i1359.photobucket.com/albums/...ps5da4934a.jpg

http://i1359.photobucket.com/albums/...psdb48833c.jpg

NEW TAILS
http://i1359.photobucket.com/albums/...ps5a42fa60.jpg

[ame="https://www.youtube.com/watch?v=ycS5aTbF9I0"]3RD BRAKE LIGHT[/ame]

NEW LED'S
http://i1359.photobucket.com/albums/...psddc7ffb1.jpg

OUT WITH THE OLD...
http://i1359.photobucket.com/albums/...psfe974ec5.jpg

IN WITH THE NEW!!!
http://i1359.photobucket.com/albums/...ps659836b4.jpg

ENGINE BAY (stage 1)
http://i1359.photobucket.com/albums/...psc73b819d.jpg

http://i1359.photobucket.com/albums/...ps6e30dd6d.jpg

http://i1359.photobucket.com/albums/...psbfd2efc7.jpg

looking good man! Keep up the work!

Very Nice, but all I could think about is how those ladies needed to get the fuck off the car..

Subscribed. Loving this build!

Quote:

Originally Posted by Khazzy (Post 1485530)

looking good man! Keep up the work!

Thanks man, your car looks great!

Quote:

Originally Posted by RZ86 (Post 1485569)

Subscribed. Loving this build!

Thanks, stay tuned it only gets crazier ;)

Quote:

Originally Posted by samisons (Post 1485565)

Very Nice, but all I could think about is how those ladies needed to get the fuck off the car..

Thanks

It was for a charity car wash at hooters, they were placed on top of the car and stayed still. Car was perfectly fine after they got off, no dents or scratches. Just fake tan and makeup. lol

Quote:

Originally Posted by chris's fr-s (Post 1485574)

Thanks man, your car looks great!

Finally u make a build book! Lol

Sub'd. In for updates.

Out of curiosity, where did those fasteners you're using for your flares come from? Haven't seen those before.

nice build so far! are this sparco seats roughly the same width at the bottom as the OEM ones? I'm looking for a set that are just a little bit wider and these look perfect

I concur with someone above. Chics look sexy, but on top of my hood and roof...hell nah...lol. Looking good thus far though on the build.

Where can I get those fender fasteners/bolts from?

Quote:

Originally Posted by SnapOv3st3r (Post 1546093)

I concur with someone above. Chics look sexy, but on top of my hood and roof...hell nah...lol. Looking good thus far though on the build.

Where can I get those fender fasteners/bolts from?

Quote:

Originally Posted by sirsol66 (Post 1546065)

Out of curiosity, where did those fasteners you're using for your flares come from? Haven't seen those before.

I ordered them from my local hardware speciality store, the are aicraft grade stainless and so easy to use, makes a perfect threaded hole. I just used three stainless rivets a nut and used a 2 ton epoxy between the nut and car.

There called "Brad Hole Tee Nut" and there not usually used on cars but because of how picky I am with my car I wanted the strongest quick threaded fastners I could get vs. the "rivet threaded inserts" (wich are some what the same just IMO not as strong)

I am only using them because I want to remove the fenders for track use (why damage them for no reason, right) and to remove my front or rear bumpers if I want and not have to worry about drilling the rivets out

Quote:

Originally Posted by hotpanda1 (Post 1546084)

nice build so far! are this sparco seats roughly the same width at the bottom as the OEM ones? I'm looking for a set that are just a little bit wider and these look perfect

Oh man they are perfect they are a little bit wider at the base but the back is so much comfotable to us bigger guys, these are fully reclineable and paired with sparco bases and sliders it is full functional (minus airbags). These are "Sparco Chronos" that i ordered from @ft86 speedfactory and they fit perfectly in the car, you would need the bases and sliders and a hardware kiy to use these seats but its worth it.

Quote:

Originally Posted by chris's fr-s (Post 1546603)

Awesome thanks a lot man, i know where my tax return is going to lol

nice build! its looking great

cant wait to see the results

Gunna look so sick! Subbed for final results

INTERIOR SHOT
http://i1359.photobucket.com/albums/...psb6e51e9b.jpg[/QUOTE]

What floor mats are those??

@chris's fr-s - how much lower (if any) did those seats lower the sitting position/height?

I love that this is an auto, I have a lot i wanna do to mine but it's auto too. Thanks for the build updates!

What ever happened to this build?!?

Is ml24 even still in business? They wont get back to me on the led frs fender vents which were supposed to be out like 2 years ago :iono:

Quote:

Originally Posted by FutureFrsOwner (Post 2504545)

I love that this is an auto, I have a lot i wanna do to mine but it's auto too. Thanks for the build updates!

Great build. Auto as well concerned about running aftermarket steering wheel. Doesn't seem to be an issue minus loosing paddle shifters and cruise. I wish the paddles where mounted on the colum .

Saw the girls on the car and immediately thought omg they might dent it!